Question about Ford E-150

1 Answer

On a 1995 Ford E150, how do I replace the key lock cylinder for the ignition.

Posted by on

  • lmitchell734 Jul 12, 2010

    That did the job! Thanks

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 17,970 Answers

Check this procedure...
1. Insert the key and turn it to the RUN position. Do not start.
2. Insert a 1/8" drill in a hole in the trim shroud below the ignition
key.
3.There is a retaining pin in the hole. Push upward and you will depress
the retaining pin.
4. As you push on the retaining pin, pull out the ignition key switch
from the steering column.
5. When reinstalling, turn the ignition key switch to the RUN position
and depress the retaining pin with your finger.
6. Insert the ignition key switch into the steering column.
7. Make sure the ignition key switch is seated and aligned before you
turn the key to OFF. This will let the retaining pin extend into the
hole.
8. Test to make sure the key goes to all the positions.

For parts replacement, can visit partsgeek and, ebaymotors

Hope helps.

Posted on Jul 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1995 lincoln towncar the radio changes one its own - bell dings even with the key out of the ignition - the ignition switch does wiggle - the battery is drained dead if the sets more then one day.


The problem is the ignition lock cylinder, and the small clip (switch) which detects the key being inserted. The lock cylinder should be replaced and most like the ignition switch too, but it is located on the right side of the steering column about 10 inches below the lock cylinder. Not an easy repair, but not brain surgery either. I suggest a professional mechanic or at least someone who has done the repair before on another FORD vehicle. Your radio changes stations because of the electrical "noise" caused by the key "clip".

Aug 18, 2014 | 1995 Lincoln Town Car

1 Answer

How do i fix this problem with my 1995 taurus ignition lock cylinder. it will turn the car on but will not shut it off?


The replacement ignition lock cylinder could be defective. This happens sometimes with electrical components.

Jul 06, 2014 | 1995 Ford Taurus

1 Answer

I cant cut it off with the ignition cylinder but i can start it an i just replaced it


the key lock cylinder is only that.the actual ignition switch is on the side of the steering column under the dash.the rod going to it from the lock may have come off. or the switch is bad.

Feb 17, 2010 | 1995 Ford Taurus

3 Answers

How to remove ignition lock cylinder without the key


How to remone 1998 windstar GL (3.8 L) Ignition Locl.

Oct 06, 2009 | 1998 Ford Windstar

1 Answer

1995 f-150 4.9L WILL START WITH THE IGNITION KET,


The lock rod is broken inside the column.You have to disassemble it to replace the lock rod actuator.

Aug 11, 2009 | 1995 Ford F150 Styleside Regular Cab

2 Answers

1995 Ford Mustang Engine Won't Turn Off


the ign switch should take care of it i agree with you

shack

Apr 18, 2009 | 1995 Ford Mustang

1 Answer

New Ignition Cylinder doesnt click in?


Lock Cylinder Functional
Removal
  1. NOTE: The following procedure applies to vehicles that have functional ignition switch lock cylinders (11582), lock cylinder keys are available for these vehicles or the lock cylinder key numbers are known and the proper key can be made.

    Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Turn ignition switch lock cylinder to RUN position.
  1. Place a 3.17 mm (1/8-inch) diameter wire pin or small drift punch in hole in lower steering column shroud (3530) under ignition switch (11572). Press retaining pin while pulling out on ignition switch lock cylinder to remove it from steering column lock cylinder housing (3511).
Installation
  1. Install ignition switch lock cylinder by turning it to RUN position. Insert ignition switch lock cylinder into steering column lock cylinder housing. Make sure ignition switch lock cylinder is fully seated and aligned in interlocking washer before turning ignition switch lock cylinder to OFF position. This will permit cylinder retaining pin to extend into steering column tube flange hole.
  1. Rotate ignition switch lock cylinder, using lock cylinder key, to ensure correct mechanical operation in all positions.
  1. Connect battery ground cable.

Apr 03, 2009 | 1995 Ford Taurus

2 Answers

Ignition switch in a 1995 ford taurus


Ignition Lock Cylinder
Ford Taurus/Sable 1986-1995 Repair Information grey_line.gif

clearpixel_002.gif clearpixel_002.gif lower_right.gif

clearpixel_002.gif

REMOVAL & INSTALLATION

Functional Lock


The following procedure applies to vehicles that have functional lock cylinders. Such cylinders either have a key available or known key numbers from which a key can be made.
  1. Disconnect the negative battery cable.
  2. Turn the lock cylinder key to the RUN position.
  3. Using a 1/8 in. (3mm) diameter wire pin or a small drift, depress the lock cylinder retaining pin through the access hole in the upper steering column shroud (under the ignition lock cylinder) while pulling out on the lock cylinder. Remove the lock cylinder from the column.

Using the key, turn the ignition lock cylinder to the RUN position, then depress the retaining pin using a wire pin or small drift

To install:
  1. Install the lock cylinder by turning it to the RUN position and depressing the retaining pin. Insert the lock cylinder into its housing. Make sure the cylinder is fully seated and aligned in the interlocking washer before turning the key to the OFF position. This will permit the cylinder retaining pin to extend into the cylinder housing.
  2. Rotate the lock cylinder using the lock cylinder key, to ensure correct mechanical operation in all positions.
  3. Connect the negative battery cable.

Non-Functional Lock
The following procedure applies to vehicles in which the ignition lock is inoperative and the lock cylinder cannot be rotated due to a lost or broken key, unknown key number or a lock cylinder cap that has been damaged and/or broken to the extent that the lock cylinder cannot be rotated.

Jan 27, 2009 | 1995 Ford Taurus

1 Answer

Ignition Lock Cylinder


There is a small button that can be pushed near the lock cylinder when the key is in the ignition and turned, the cylinder can be pulled out then.

Dec 10, 2008 | 1995 Ford Bronco

1 Answer

1997 ford contour


this is for 98, but may apply if yours is late 97 build.

Article No.
98-21-14
  • IGNITION SWITCH - HIGH EFFORT IGNITION KEY INSERTION/REMOVAL AND/OR KEY CHIMES SOUND WITH DOOR OPEN AND IGNITION KEY REMOVED
Publication Date: OCTOBER 15, 1998
FORD: 1998 CONTOUR LINCOLN-MERCURY: 1998 MYSTIQUE
1999 COUGAR
This TSB article is being republished in its entirety to include the 1999 Cougar . ISSUE: The ignition key may be difficult to insert or remove and/or key chimes may sound with the ignition key removed and driver's door open on some vehicles. This may be caused by internal design characteristics in the ignition lock cylinder increasing insertion/removal efforts which may allow the lock cylinder to stick.
ACTION: Install a revised ignition lock cylinder. The revised ignition lock cylinder should reduce the possibility of high insertion/removal efforts and ensure proper chime function. Refer to the following Service Procedure for details.
SERVICE PROCEDURE
  1. Verify customer concern.
  2. Observe the ignition lock cylinder as the key is removed. If the lock cylinder snaps outward to the non-depressed position and the chimes stop sounding, continue to Step 3. If it does not snap outward, replace the ignition lock cylinder with the appropriate cylinder by referring to the Parts Block in this article.
  3. Insert and remove the ignition key from the lock cylinder. If binding or high efforts are encountered, replace the ignition lock cylinder.
  4. From the Parts Block, select a lock cylinder with a part number suffix identical to the center character of the key code of the vehicle. The suffix must match the center key code character to maintain a single key system.
  5. Install the replacement lock cylinder, by referring to the 1998 Contour/Mystique Workshop Manual, Section 211-05 or the 1999 Cougar Workshop Manual, Section 211-04. NOTE: KEYS INCLUDED WITH NEW IGNITION LOCK CYLINDERS ARE CUT FOR THE IGNITION ONLY. IN ORDER FOR THE KEYS TO FUNCTION IN THE DOOR LOCKS, THE KEYS MUST BE CUT TO THE DOOR CODE OF THE ORIGINAL LOCKSET. THE KEY CODE WILL CHANGE UPON INSTALLATION OF THE REPLACEMENT LOCK CYLINDER (FIGURE 1).

    tw2114~us~en~file=tb5525a.gif~gen~ref.gif
    Figure 1 - Article 98-21-14

    NOTE: ADVISE THE CUSTOMER TO DISCARD ALL KEYS THAT WERE CUT TO THE ORIGINAL IGNITION LOCK CYLINDER.
  6. Record the new key code on the repair order and provide to the customer. Advise the customer to record the new key code in a permanent location and to discard all references to the original key code. NOTE: REPLACEMENT IGNITION LOCK CYLINDERS ARE SHIPPED WITH NON-PASSIVE ANTI-THEFT SYSTEM (PATS) KEYS. IF THE VEHICLE IS EQUIPPED WITH PATS, OBTAIN TWO (2) ROTUNDA KEY BLANKS (OR OTHER FORD AUTHORIZED BLANKS, SUCH AS: ILCO, STRATTEC, CURTIS, HUF, OR VALEO) AND CUT TO THE REVISED KEY CODE. USE OF OTHER UNAUTHORIZED KEYS MAY CAUSE ERRATIC OPERATION OF THE PATS SYSTEM.
  7. Program PATS keys using one of the two following methods:
(1) For vehicles with Integrated PATS (IPATS), function built into the Powertrain Control Module (PCM) and built beginning:
  • 2/2/98 Kansas City (Contour/Mystique)
  • 2/16/98 Mexico (Contour/Mystique)
  • All 1999 Cougars
Using the New Generation Star (NGS) Tester equipped with Service card (green) level 3.0 or higher:
  1. From NGS menu, select:
    • Service Bay Functions
    • PCM
    • Enter Security Access (10 minute delay)
    • Ignition Key-Code-Erase
  2. Disconnect Data Link Connector (DLC).
  3. Cycle the first non-programmed key in the ignition to run position for at least 3 seconds and then turn to the off position.
  4. Cycle the second non-programmed key in the ignition to run position. The theft indicator should prove out for 3 seconds.
  5. Verify the vehicle will now start using both keys.
(2) For Contours/Mystiques with Stand Alone PATS and built before:
  • 2/2/98 Kansas City
  • 2/16/98 Mexico
Using the New Generation Star (NGS) Tester equipped with Service card (green) level 1.0 or higher:
  1. From NGS menu, select:
    • Service Bay Functions
    • PATS
    • Ignition Key-Code-Erase (this process may take up to 8 minutes to complete )
  2. Disconnect DLC.
  3. Cycle first unprogrammed key in the ignition to run position. First key will program and allow vehicle to start.
  4. Again cycle first programmed key to run position. Within 15 seconds, remove original key and turn new unprogrammed key to run position. The theft indicator should prove out for 2 seconds. New key will start vehicle.
  5. Repeat this process for additional key programming. NOTE: THE FOLLOWING SHOULD BE NOTED FOR THE PART NUMBER BLOCK:
    • Part Number suffix will match center character in key code
    • Logo on key is Ford for Contour models
    • Logo on key is Mercury for Mystique and Cougar models


PART NUMBER PART NAME F5RZ-11582-A Ignition Lock Cylinder (Contour) F5RZ-11582-B Ignition Lock Cylinder (Contour) F5RZ-11582-C Ignition Lock Cylinder (Contour) F5RZ-11582-D Ignition Lock Cylinder (Contour) F5RZ-11582-E Ignition Lock Cylinder (Contour) F5RY-11582-A Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-B Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-C Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-D Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-E Ignition Lock Cylinder (Mystique, Cougar

Aug 13, 2008 | 1997 Ford Contour

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...