Question about 2006 Cadillac CTS

1 Answer

06 cts when you turn wipers on windshield washer pump runs continually if you turn the wipers off the water shuts off. I have replaced the (D01 D6377D -) Windshield Wiper & Windshield Washer switch cross Reference for gm Part Number: 1999309 Still doing the same thing any ideas what the problem might be?

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Cadillac Master
  • 2,509 Answers

-I believe the switch is bad. The line to the pump might stuck at the wipe position. So every time it on. It turn both
devices on.
Check it out.

Good luck


Mai

Posted on Dec 21, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 81424 Answers

SOURCE: Windshield Wiper Arm

Pull up on the wiper arm, you will see a tiny little blade on the side of the wiper arm where it goes over the post, take a little screwdriver and pry that out board, this will release the arm from the post, it will be tight, wiggle the arm and pull straight out away from the post.

Posted on Oct 19, 2008

jetwash
  • 43 Answers

SOURCE: windshield wiper

1) listen if windshield wiper motor is turning when switched on. The motor is under hood up near firewall.
If no noise and fuses are OK, motor may need replacement.

2) If motor can be heard whirring, then maybe the plastic link between the motor shaft and the wiper arm assy has worn or broken. (A very cheap part). This can be accessed by removing cowling or vents in front of windshield. This is a common failure.

Posted on Oct 26, 2008

  • 22 Answers

SOURCE: 98 camry windshield wiper

You will have to change the swich that control the wiper blades cause sometimes they go bad

Posted on Dec 17, 2008

  • 1 Answer

SOURCE: windshield wiper on driver's side of Hyuandi doesn't work -

I recently had the same problem of the drivers side wiper not working. My boyfriend (a mechanic) took the windshield cowl off and looked to see what was going on. He originally thought that maybe something had slipped off. I'm going to describe what he found in layman's terms. When you take off the wiper blade arms from the wiper transmission assembly unit there are these silver colored nubs with grooves on them (one for each wiper). What he found was that on mine the grooves were stripped so that the wiper on the drivers side wouldn't catch and go across the windshield while the other wiper worked fine. What we think that happened is that I left the wipers on when I shut off the car and since we had a huge snowstorm the wiper transmission bound up and stripped the nubs when I turned on the vehicle the next day and let it warm up. I had tried for the past week to find a used replacement wiper transmissions assembly but was not successful. I just ordered the part from my local Hyundai dealer at a cost of $180. I will at least save on the labor, as my boyfriend can handle that part. If you try to get the part used, be careful. There was a product change mid-year. Prior to June 2004 (If I remember correctly) is one part number and Santa Fe's manufactured after that date is a different part. I needed the earlier Santa Fe part. You can look at the body panel between the front and back doors on the driver's side for the production date of your vehicle there is a metal decal with the vin, your color codes, and other information.

Posted on Mar 19, 2009

  • 58 Answers

SOURCE: Windshield wiper fluid won't squirt

When you pull the lever to activate the windshield washers, do you hear any type of sound coming from under the hood?  A whirring sound should be heard from the little electric pump that feds the washers.
If you can hear the whir, then you should look for a possible clog in the washer hoses (there is more than one...).
If you cannot hear the whirr, then you should check the fuse that protects the windshield washer circuit.  Check your owner's manual for the location and correct amperage for this circuit.
Good luck!

Posted on Jun 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When I turn the switch to my 2006 Cadillac DeVille CTS windshield wiper it does nothing no sound no movement what is wrong


Hard to say what's wrong without testing thing's . Is there B+ voltage to the wiper switch ? B + voltage to the wiper motor ? Do you know how to use a voltmeter ? How to test electrical circuits ?
Here is a factory service manual list of componets involved .
Wiper/Washer System Components
The Wiper/Washer System consists of the following electrical components:
• Accessory relay
• Heated washer nozzles w/XA7
• WASH NOZ 10A fuse
• Windshield washer fluid level switch
• Windshield washer pump motor
• Windshield wiper motor
• Windshield wiper motor module
• Windshield wiper/washer switch
• Wiper/washer switch 10A fuse
• Wiper motor 30A fuse

Do you know how the wipers work ?
Windshield Wiper Motor Wiring Tutorial
Wipers Inoperative - All Modes ?????
Wiper Motor Switch Troubleshooting

Sep 05, 2017 | Cadillac Cars & Trucks

1 Answer

Windshield wipers won't turn off on 2005 cadillac cts. Pulled the fuse and they did not stop.What could be the issue?


There could be a defect in the windshield wiper/washer module or the wiper switch.

Oct 09, 2016 | 2005 Cadillac CTS

1 Answer

Why is my windshield wipers running in the off position, it's like they are running in the intermittent position, but it's in the off position.


When the windshield wiper / washer switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the wiper motor module will continue to operate the wiper motor until the wipers reach the park position. If the ignition is turned off while the wipers are in mid-cycle, the wipers will stop immediately where they are. The wipers will park the next time the ignition is cycled to the ON position.

Schematic Reference: Wiper/Washer Schematics


1

Did you review the Wiper/Washer System Description and Operation and perform the necessary inspections?
Go to Step 2
Go to Symptoms - Wiper/Washer Systems

2

  1. Turn the ignition ON.
  2. Turn the windshield wiper/washer switch OFF.
Are the windshield wipers always on?
Go to Step 3
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

3

Disconnect the windshield wiper/washer switch connector.
Are the windshield wipers always on?
Go to Step 4 if yes
Go to Step 7 if no

4

  1. Disconnect the windshield wiper motor connector.
  2. Test the windshield wiper switch signal 1 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 5

5

Test the windshield wiper switch signal 2 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 6

6

Test the windshield wiper motor high speed circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 9

7

Inspect for poor connections at the windshield wiper/washer switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 8

8

Replace the windshield wiper/washer switch. Refer to Windshield Wiper and Washer Switch Replacement - On Vehicle in Steering Wheel and Column.
Is the repair complete?
Go to Step 11
--

9

Inspect for poor connections at the windshield wiper motor. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 10

10

Replace the windshield wiper motor. Refer to Windshield Wiper Motor Replacement .
Is the repair complete?
Go to Step 11
--

11

Operate the system in order to verify the repair.
Did you correct the condition?
The Wiper / Washer System consists of the following components:
?€¢
Windshield wiper / washer switch


?€¢
Windshield wiper system module / motor


?€¢
Windshield washer fluid pump


?€¢
Windshield washer fluid level switch


?€¢
Instrument panel cluster (IPC)


?€¢
ACC 15-amp fuse


?€¢
WSW 30-amp fuse

Jan 04, 2016 | 2002 Pontiac Bonneville

2 Answers

Why when i push the button for my winshield my wipers work but no washer fluid comes out and i dont hear the sound like the motor is not running...can anyone help me?


If you have washer fluid in the contaner under your hood, then have someone listen with the hood up to see if the motor on the pump runs. If it does not run you have a loose connection usually at the washer motor or a bad fuze to the water pump. Fuse is in the fuse cluster, usually under the dash.

Nov 17, 2015 | Cars & Trucks

2 Answers

I have a 2007 mustang an the wipers wont turn off I had 2 pull the fuse to turn them off can u help me


The windshield wiper motor is a smart wiper motor with an integrated electronics module. The internal components of the motor are the high/low relay, washer pump relay, and the run/park relay and associated electronics.
The windshield wiper motor receives its inputs from the windshield wiper/washer switch. These signals are ground reference signals. When the switch is placed in different positions, various input signals are selected and sent through circuits to the motor. The windshield wiper motor module identifies these selected input signals and activates the motor to the selected function.!
Your probably going to need a new wiper motor ! ! ! But you should always test before replacing parts !
Visual Inspection Chart Mechanical Electrical
  • Windshield washer pump hoses
  • Windshield wiper mounting arm and pivot shaft
  • Bussed electrical center (BEC) fuse 10 (30A)
  • Smart junction box (SJB) fuse 3 (10A)
  • Circuitry
  • Windshield wiper motor
  • Windshield washer pump
  • Windshield wiper/washer switch
  • The wipers stay on continuously
  • Circuitry
  • Windshield wiper motor
  • Windshield wiper/washer switch
  • Go To Pinpoint Test C .
PINPOINT TEST C: THE WIPERS STAY ON CONTINUOUSLY s6b~tr~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use the correct probe adaptor(s) when making measurements. Failure to use the correct probe adaptor(s) may damage the connector.
Test Step Result / Action to Take C1 CHECK THE WINDSHIELD WIPER/WASHER SWITCH
  • Key in OFF position.
  • Disconnect: Windshield Wiper/Washer Switch C2137.
  • Carry out the windshield wiper/washer switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
  • Does the windshield wiper/washer switch pass the component test?
Yes
GO to C2 .

No
INSTALL a new windshield wiper/washer switch. REFER to Wiper/Washer Switch in this section. C2 CHECK CIRCUITS 56 (DB/OG), 58 (WH), 61 (YE/RD), AND 63 (RD) FOR A SHORT TO GROUND
  • Disconnect: Windshield Wiper Motor C125.
  • Measure the resistance between the windshield wiper motor C125, harness side and ground as follows:

    Windshield Wiper Motor C125 Pin Circuit C125-10 56 (DB/OG) C125-11 58 (WH) C125-1 63 (RD) C125-9 61 (YE/RD)

    s6b~tr~en~file=n0011980.gif~gen~ref.gif
  • Are the resistances greater than 10,000 ohms?
Yes
GO to C3 .

No
REPAIR the circuit(s). TEST the system for normal operation. C3 CHECK FOR CORRECT WINDSHIELD WIPER MOTOR OPERATION
  • Disconnect all the windshield wiper motor connectors.
  • Check for:
    • corrosion.
    • pushed-out pins.
  • Connect all the windshield wiper motor connectors and make sure they seat correctly.
  • Operate the system and verify the concern is still present.
  • Is the concern still present?
Yes
INSTALL a new windshield wiper motor. REFER to Wiper Motor in this section. TEST the system for normal operation.

No
The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.
You

Feb 20, 2015 | 2007 Ford Mustang Coupe

1 Answer

How do i get to the washer pump on a 1994 toyota camry?


I don't think any Camrys that year had rain sensing wipers so you could be right. Anyway to get at the pump you have to unscrew fixings and lift up the washer reservoir to disconnect the wiring, then remove the reservoir.

Jun 15, 2017 | 1994 Toyota Camry

1 Answer

Washer comes on when wipers are turned on. Is replacing the switch gonna fix it? 06 cts


Should. It sounds like wiper switch w/delays/squirters, etc has a short in it and it's activating your washer pump in all positions.

Jan 07, 2011 | 2006 Cadillac CTS

3 Answers

I have a 2003 Chevy Trailblazer Windshield Wiper problem.


As it turns out, there is a recall On 2002-2003 Chevy Trail Blazer's
Windshield Wiper/washer
NHTSA No. 04V046000
Recall Date: Feb, 4th, 2004
Call your dealer to see if this is still under the recall to be fixed.
RECALL: 2002 - 2003 Chevrolet Trailblazer NHTSA Campaign Number: 04V046000 www.nhtsa.dot.gov
Manufacturer GENERAL MOTORS CORP. Recall Date: FEB 02, 2004 Potential Number Of Units Affected: 581394 Description VISIBILITY:WINDSHIELD WIPER/WASHER Summary CERTAIN SPORT UTILITY VEHICLES HAVE WINDSHIELD WIPER SYSTEMS THAT WILL NOT TURN ON, CEASE OPERATION WHILE IN USE, FAIL TO TURN OFF/ON BY THEMSELVES (MOISTURE SENSITIVE WIPER SYSTEM), OR HAVE CONTINUOUS WINDSHIELD WASHER PUMP OPERATION BECAUSE THE PRESENCE OF WATER WITHIN THE WIPER MODULES CAN EITHER CAUSE A SHORT CIRCUIT OR CAN LEAD TO THE CORROSION OF COMPONENTS WITHIN THE MODULE. Consequence DEPENDING ON THE OCCURRENCE AND WEATHER SITUATION, DRIVER VISIBILITY COULD BE REDUCED, WHICH COULD RESULT IN A CRASH. Remedy DEALERS WILL COVER THE WINDSHIELD WIPER MODULE VENT HOLE WITH A PATCH. ALSO, THE WIPER MOTOR, CIRCUIT BOARD, AND ELECTRICAL CONNECTOR WILL BE INSPECTED TO SIGNS OF WATER INTRUSION AND/OR CORROSION AND BE REPLACED AS REQUIRED. THE RECALL BEGAN JULY 6, 2004. OWNERS SHOULD CONTACT CHEVROLET AT 1-800-630-2438; OLDSMOBILE AT 1-800-630-6537; OR GMC AT 1-866-996-9463.

Nov 25, 2008 | 2003 Chevrolet TrailBlazer

Not finding what you are looking for?
2006 Cadillac CTS Logo

Related Topics:

527 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

Marvin
Marvin

Level 3 Expert

81424 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...