Question about 1995 Ford F350

1 Answer

Where is the egr valve & position sensor located on a 1995 ford f-350 with a 460

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Contributor
  • 478 Answers

The egr valve is located on the valve cover and has a 1/2 hose connected to it going to air cleaner.
The position sensor is located at the front bottom of motor it is looking at the harmonic balancer at the front bottom pulley under the fan blade pully.

Posted on Jul 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the probable cause(s) of DTC P1406?


Definition of Diagnostic Trouble Code P1406 Audi: EGR Temperature Sensor Range/Performance BMW: Heated Catalyst Internal Control Module Checksum/ROM Error Buick: EGR Valve Pintle Position Circuit Cadillac: EGR Valve Pintle Position Circuit Chevrolet: EGR Valve Pintle Position Circuit Ford: Differential Pressure Feedback Sensor Downstream Hose Off Or Plugged GMC: EGR Valve Pintle Position Circuit Isuzu: EGR Valve Pintle Position Circuit Lincoln: Differential Pressure Feedback Sensor Downstream Hose Off Or Plugged Mazda: DPFE Sensor Downstream Hose Off Or Plugged Mercury: Differential Pressure Feedback Sensor Downstream Hose Off Or Plugged Oldsmobile: EGR Valve Pintle Position Circuit Pontiac: EGR Valve Pintle Position Circuit Saturn: EGR Valve Pintle Position Circuit Toyota: Turbo Pressure Sensor Range/Performance Problem Volkswagen: EGR Temperature Sensor Range/Performance Volvo: Termperature Warning > 100 degrees C

Jun 18, 2015 | Cars & Trucks

1 Answer

EGR SYSTEM PROBLEM ON 1999 EXPLORER


sounds like a job for a Chilton's guide..

Jun 04, 2008 | 1999 Ford Explorer

1 Answer

I need a list of all emission control devices on a 96 ford explorer for a paper im writing for my apprenticeship


1996 Ford Explorer 2WD 5.0L


Canister Purge Valve
Catalytic Converter

EGR Position Sensor

EGR Vacuum Solenoid

EGR Valve

EGR Valve Gasket

EGR Valve Pressure Sensor

Exhaust Manifold

Exhaust Manifold Gasket

Fuel Cap

Muffler - Performance

Oxygen Sensor

PCV Valve

Sensor - Ambient Air Temperature

Smog Pump

Jan 15, 2011 | 1996 Ford Explorer

4 Answers

Have a 1995 ford contour and took it to pepboys and they got multiple codes. One of the codes came up twice code 332 says egr valve not opening could this cause all the other codes? My husband has checked...


DTC P0332 is for a knock sensor, not egr valve. That's not to say one of the multiple codes you've mentioned wasn't for the egr valve.

What are some of the characteristics the vehicle is showing. By the way, what is the vehicle? In one place it says 1995 contour, in another it says 1995 explorer.

Jan 03, 2011 | 1994 Ford Explorer Limited

1 Answer

Where is the egr valve position sensor located on a 2002 Ford Taurus SE?


I dont think it has one... there is a sensor on the egr pipe that telsl the computer if the egr is operating or not. Its the PDFE sensor, it looks like a little box with 2 hoses on the egr pipe.

Dec 03, 2010 | 2002 Ford Taurus

2 Answers

PO402 trouble code....how is this repaired


Exhaust gas recirculation flow excessive. First things to check is your vacuum hoses to egr position sensor (Dpfe sensor) Egr solenoid & egr valve. If they are off, melted or sucked in they need to be replaced. Usually a specific code will be set for that but not always. Of the three the dpfe sensor also known as egr position sensor is the most common & easiest to replace. Next in order is the egr solenoid. Lastly if it comes to changing egr valve make sure to clean all carbon build up in cavity that egr mounts to. They commonly plug up.

Sep 24, 2010 | 2002 Ford Explorer Sport

1 Answer

How to replace egr valve on 1995 crown vic 4.6. Valve is in hard place to get to.


On 1995 Crown Victoria the EGR valve is located at the rear of the engine compartment. While the attaching bolts can be gotten out with a little bit of a problem the egr tube that atteches the EGR valve to the right exhaust manifold is a pain. It is possible to do though. Here are the removal and installation instructions. If you are sure that the EGR valve is the reason for any check engine light then you can remove the battery cable for about five minutes to reset the light, but if the light is on for a differant reason then you just got rid of the code plus any freeze frame data that a shop could have used to diagnose the problem.

Check this procedure about REMOVAL & INSTALLATION...

PFED Sensor
See Figures 9, 10, 11 and 12


bcc2045.jpg
Fig. 9: Detach the connector for the DPFE sensor


78e8250.jpg
Fig. 10: Matchmark and remove the vacuum hoses for the DPFE sensor and ...


daae4e4.jpg
Fig. 11: ... remove the retaining nuts from the DPFE sensor and ...


b6fd561.jpg
Fig. 12: ... remove the DPFE sensor from the intake manifold
  1. Disconnect the negative battery cable.
  2. Label and disconnect the wiring harness from the DPFE sensor.
  3. Label and disconnect the vacuum hoses.
  4. Remove the mounting screws and remove the DPFE sensor.
To install:
  1. Position the DPFE sensor and tighten the mounting screws.
  2. Attach all necessary hoses and wiring to the sensor.
  3. Connect the negative battery cable.

EGR Valve Control Solenoid
See Figures 13 through 17


bb3e162.jpg
Fig. 13: Detach the connector for the EVR solenoid


a9fc1b4.jpg
Fig. 14: Match mark the vacuum hoses for the EVR solenoid and ...


57ba344.jpg
Fig. 15: ... remove the vacuum hoses from the EVR solenoid


f5d5cc2.jpg
Fig. 16: Remove the retaining nut for the solenoid and ...


4b98f79.jpg
Fig. 17: ... remove the solenoid from the intake manifold
  1. Disconnect the negative battery cable.
  2. Label and detach the vacuum hoses from the EVR solenoid.
  3. Detach the electrical connector from the solenoid.
  4. Remove the retaining hardware, and remove the solenoid.
To install:
  1. Position the solenoid and install the retaining hardware.
  2. Attach the main emission vacuum control connector and the wiring harness connector to the EVR solenoid.
  3. Connect the negative battery cable.

continue...

Jul 16, 2010 | 1992 Ford Crown Victoria

2 Answers

1995 Ford Taurus Sho 3.2 check engine light blink 3 3 1 3 3


Code 33 is EGR opening not detected, this is caused by a plugged EGR exhaust passage in the upper intake manifold, this is a common SHO engine fault, the valve works but the engine does nothing that the computer can sense, since no gas flows, to verify this is the problem open the egr at idle, the engine should almost die, if nothing happens or only a tiny change in idle speed or quality the passages are plugged, if it does stall or get real rough the egr position sensor (usual code for sensor is 32) may be faulty or the valve is sticking. I was a ford dealer tech for 30 years and did quite a few of these, there is a TSB (technical service bulletin) about this problem

Oct 12, 2009 | 1995 Ford Taurus

2 Answers

Need location of the erg sensor 2000 ford ranger


The egr valve has two sensors. One is an EGR position sensor which is physically attached to the EGR valve. The other sensor is the DPFE (Delta Pressure Feedback EGR) sensor, commonly called the EGR pressure sensor. It's location varies depending on the engine you have. You can fine this sensor by following the vacuum hose on the EGR valve. It will be with in inches of the EGR valve. The sensor will be black (plastic) or silver (metal), have two or three vacuum ports and an electrical connection on it.

The vacuum pressure sensor is a high failure item on fords. Any Ford parts department will have one in stock, as well as some aftermarket parts stores.

The new sensor may not look exactly the same as the old part, but will have all the hook ups as the old one. You may also need to replace the vacuum hose to the sensor as well

Feb 24, 2009 | 2000 Ford Ranger SuperCab

2 Answers

Location of the egr sensor on 2000 ford ranger


The EGR pressure sensor is located within inches of the EGR valve. The exact location varies depending on the engine (2.5L, 3.0L or 4.0L). It is usually attached to the upper intake manifold with two small bolts.

Feb 24, 2009 | 2000 Ford Ranger SuperCab

Not finding what you are looking for?
1995 Ford F350 Logo

Related Topics:

441 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...