Question about 1987 Ford Econoline

1 Answer

Have 1987 ford cutvan don't have manual to figure which fuses go to what have a couple of lights out and directional only works on right

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 22,219 Answers

You have a bad earth on the light units by the sound of it ,check for a feed with a meter and run another earth wire from the light clusters ,the indicators could be the switch so test using the hazards

Posted on Jul 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1987 ford ranger turn signals keep blowing fuses. have changed flasher fuse and switch on column. just keeps blowing?


first thing i guess to understand what is going on here ,is a little back to basics on how turnsignals work , first item you have is power fuse then it's off to flasher module than it goes to the turnsignal switch on colum ,of course anywhere on it way to there the power could got to ground and cause the fuse to trip, now the power depending on Left or right selection , is directed to lights on both front and back of truck,thankfully rangers don't have em on the side) now any place in this pathway the wire could go to ground and blow the fuse, now to troubleshoot and narrow down the area that fault is located , (1) replace fuse with correct size and ck for proper fit in fusebox and start and operate truck for a few minutes DO not use turnsignals, ck fuse is it still good if so go to step 2 if not stop and ck wire conditions in steering colum and switch(2) start truck and try right hand turn signal only verify lights working ,Ok yes/no if not replace fuse and try left side same way, Ok yes /no if right or left side only blows fuses take ALL bulbS OUT of lights and try again , if fuse still blows then look for wire fault on that side of truck if fuse is still good then look carefull at light bulb sockets for rust and powered corrosion (ill bet an 87 has some ) you may need to replace bulb sockets , they do sell em in autoparts stores .

Jun 30, 2014 | 1987 Ford Ranger

2 Answers

I have 89 bronco 2 my brake lights turn signals both work my tail lights don't work have check fuse n blubs what might be the problem


The turn signals and brake lights use the same circuit and filament in the bulbs. The tail lights are on the other circuit which comes from the headlight switch.
Do you have power on the tail light fuse ?

Feb 25, 2013 | 1987 Ford Bronco II

1 Answer

Where are the tail light fuses located on a 1998 ford expedition?


what fuse controls the right taillight in a 98 ford expedition xlt

Jun 09, 2012 | 1998 Ford Expedition

1 Answer

The headlights and high-beam search lights on my 1987 Toyota land cruiser wont turn on. Is this a fuse problem? If so where is the corresponding fuse/fuse-box located? I've already look on the und


The left and right headlights are on different fuses. If both are not working, you need to check the fusible link, headlight relay, and the switch itself. See diagram below.
0900c1528004d7e2-dwbgzyjx1s1bj3innjxcfx0i-3-0.gif

Jun 15, 2017 | 1987 Toyota Land Cruiser

1 Answer

I have an 01 ford Powerstroke and the dash lights and tail lights dont work. i just replaced the headlight switch today. Still have the problem


Dash lights and tail lights are commonly on the same circuit. When your dash lights go out, you know you don't have any tail lights. Pull out the owner's manual and figure out which fuse (or fuses) are for the tail lights.

Sep 19, 2011 | 2001 Ford F350 Super Duty SuperCab

1 Answer

My name is Dave, any help would be much appreciated! When I turn on the left or right directional indicator from the lever on the steering column it makes a rapid blinking on the control panel, the front...


Hi, I have a couple of questions.
1. were the signals working before you replaced the brake light bulbs, and did you use the recommended bulbs?
2. Do the brake lights work now?

The brakes and signals use the same filaments, so these things are tied together.

Jul 31, 2011 | Volvo 240 Cars & Trucks

1 Answer

1987 Ford Escort GT tail and brake lights not working.


It is the light box. You know the pulley you use to turn lights on and off??? that goes bad all the time. Replace that and your gold.

Mar 03, 2010 | 1987 Ford Escort

1 Answer

1987 ford escort will not start has power?


have you noticed anything else stop working on the car/van ie heating cigaretter lighter etc, if so it could be the fuse box, ford escorts are renowned for the fuse boxes to go. also another suggestion is to check all of the earth straps, mine used to cut out when i used to turn right because of a dodgy earth, then the fuse box packed in

Jan 24, 2009 | 1987 Ford EXP

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...