Question about 1998 Buick Skylark

1 Answer

I need to installe a thermostat. - 1998 Buick Skylark

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 57 Answers

IF YOU FOLLOW THE RADIATER HOSE TO THE ENGINE BLOCK THERE ARE 2 SCREWS IT IS THERE

Posted on Jul 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 chevy camaro z28 turns over wont start


It needs a kick start installled in it,

Nov 02, 2012 | Chevrolet Cars & Trucks

1 Answer

How do I change a thermostat in a 2003 chrysler sebring?


Parts Approx...... $70
Labour ...............2 hour. May take up to 8 Hours. It Depends on your experience how fast you get the job done.

Location. its located somewhere behind the alternater. so you must romove alternator. (Ac Compressor removal is optional)

1. Disconnect Battery Cable,
2. Raise the car on Hoist Or Jack up
3. Drain Coolant from Radiator
4. Remove Right Front Wheel and Splash Shields
5. Remove Belt and Tensioner
6.Remove Dip Stick Bolt + remove Dip Stick tube. ( cover dip stick hole so that coolant dosunt get in to oil pan) or (Do an oil change if coolant gets in to oil pan)
7. Remove Lower Alternator Bolt
8. Remove Uper Alternator Bolts (Access from the Hood).
9. Remove All the Connections to the Alternator and Ac.
11. Remove Thermostat housing bolts
12. Remove thermostat

to installl Reverse the procedure and at the end open the bleeder valve and pour in coolant slowly in to the reservoir

Start Engine

add coolant and bleed the air out.
let the thermostat valve open and cerculate coolant untill Rad cooling fan cycles.

thats it you are done!!

Oct 23, 2010 | 2003 Chrysler Sebring

1 Answer

I NEED FACTORY CAR STEREO WIRING DIAGRAM FOR 2007 FORD RANGER


check on installer doctor installl dr
or just ask a specific question about what wire you are looking for

Feb 23, 2010 | 2007 Ford Ranger FX4 Off-Road

1 Answer

Oil leak from right side of engine


sounds to me like a valve cover gasket need to be installled, very cheap an easy to do. Try to see if the bolts are loose, if so that can also cause a oil leak.

Jan 14, 2010 | 1997 Buick LeSabre

1 Answer

How do I remove the front headlight to replace the bulb


there are two 7mm long bolts on top of headlamp assambly of course need to open hood to be able to see them and have to be carefull when removing and installling headlamp assambly

Nov 17, 2009 | 2002 Chrysler Concorde

1 Answer

Serpantin belt replacement? I need a manual!!!


You need a 14mm socket on a extended breaker bar,
place on automatic tensioner center pulley bolt which is the dumpy pulley located above the alternator.
Move the nut to tighten which will move spring loaded tensioner to low side which will allow you to slip belt off.....installlation is the reverse
~KS

Nov 14, 2009 | 2002 Isuzu Axiom

1 Answer

Is replacing the waterpump and thermo hard


NO. the top radiator hose is where the thermostat is,r&r the bolts set the hose and the goose neck to the side remove the gasket and the thermostat,replace the new one in the reverse order.(pay attention to the direction of the thermostat when you install it.
The water pump loosen the belts, drain the radiator using the pet **** under the radiator,or you may use the bottom radiator hose,take it off the water pump and drain into your pan.r&r the bolts from your pump and remove the pump.Clean your gasket area and installl new one in reverse order.

Aug 01, 2009 | 1985 Cadillac Eldorado

1 Answer

I have a 1999 dodge 1500 4x4 i replaced the rad and heater core and now thermostat and water pump 2 months ago/it is over heating and not putting out any heat in the cab antifrezze is comming out the over...


it will be one of two things air is in the system or the thermostate is wrong or installe wrong. to get air out remove rad cap when cold turn heat on floor and run vehicle while watching fluid level in rad, sometimes you have to run at 1500 rpms for a while to get engine temp up but be careful when you let off throttle the water will come right at you so cap it off before you let off throttle

Jan 16, 2009 | 1999 Dodge Intrepid

2 Answers

200 gmc jimmy st heater


Had similar problem in my 2000 Jimmy. No hot air from heater. Had the shop (Midas) disconnect heater hoses at the fire wall and blow out the heater core with air hose. Got rust and junk blown out. Hooked up and flushed system with new anti freeze. Got lots of heat now.

Oct 25, 2008 | 2000 GMC Jimmy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...