Question about 2002 Hyundai Santa Fe

Open Question

I need the torque settings for the dual mass flywheel on a santa fe crdt

Posted by on

6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 1263 Answers

SOURCE: correct wheel torque to apply after rotating tires

100 ft pounds of torque is required

Posted on Nov 07, 2008

  • 122 Answers

SOURCE: need torque specs for intake plenium on a 2004 v6

Check on

Posted on Feb 21, 2010

  • 1857 Answers

SOURCE: i can't figure out how to set the timing on my 05

Thats beacause you cant. The timing is computer controlled. If the timing was an issue you would havea code indicating it.

Posted on Apr 06, 2010

  • 2187 Answers

SOURCE: I replaced the clutch assy. in a 2003 santa fe 2wd

Check if there is air in the system. You need to bleed out the clutch. Inspect the pedal linkages for binding or anything out of the ordinary. If bleeding the clutch did not resolve the issue, you need to go back to the transmission and inspect the fork or pivot ball. It could be possible that the conversion kit did not match the model that you have. It is possible that bad seals causing debris may have caused the issue and it was just coincidence that after replacing the flywheel did this happen.

You may also need to replace transmission fluid.

Posted on May 12, 2011

  • 1280 Answers

SOURCE: need head bolt torque for

Go to and register your vehicle by VIN #.. you'll then have access to wiring diagrams, shop & owner manuals, service bulletins, campaigns, illustrations and procedures, etc

Posted on Sep 12, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Torque bolts for flywheel 2003 Hyundai Santa Fe

94 -101 ft/lbs- dip the bolts in clean engine oil or use never-seize on threads. use new bolts

Feb 06, 2015 | 2003 Hyundai Santa Fe

1 Answer

How do I remove the intercooler from my 2007 Santa Fe 2.2CRDT?

maybe the radiator? the thing that sits in front of the engine with the fan aimed at it? in that case, youll probably have to take off the fan housing, drain it via the drain plug at the bottom left or bottom right of it (dont do that if you have had the engine running recently itll burn) let it drain. take off all of the hoses connected to it, then it will be secured somehow around the edges, undo those points and it should come out. id suggest taking another approach at getting the 4th screw out however. smaller/different angled tools often do the trick

Oct 20, 2012 | 2007 Hyundai Santa Fe Limited

1 Answer

Dual mass flywheels

for light vehicle, recommended torque is 45 newton meter and an additional 3/4 turn of the wrench and for 6 bolts tightening sequence should be 3 by 3 as star delta.

Feb 22, 2012 | 2005 Renault Laguna II

1 Answer

How do I change the fuel filter on a 2006/7 Hyundai Santa Fe 2.2 CRDT CDX safely?

There is no external type fuel filter on the Santa Fe. It is built into the fuel pump module in the tank,you rould have to remove your rear seat bottom cushions and get to the access plate and remove the pump module. Can be very time consuming if you have never done this before.

Oct 20, 2011 | 2007 Hyundai Santa Fe Limited

1 Answer

Just had clutch need replaceing for the 3rd time in 18months. Been told driver error. Have driven hyundi for 10 years and never had problem before

if it was worn out then it could be driver error,but if you suffered a very bad vibration from the clutch the it is the dual mass flywheel that is the problem...may need replacing.

May 14, 2010 | 2003 Hyundai Santa Fe

1 Answer

Need torque settings for dual mass flywheel in 3.0 isuzu trooper

diesel 4JX1 engine
apply engine oil to threads
1st- 59Nm(43lb ft)
2nd- 60-90deg.
3rd- 60-90deg.

Jan 03, 2009 | 2001 Isuzu Trooper

1 Answer

2003 Tiburon 6 spd clutch replacement now tranny won't respond

Possibility, you may have intalled the clutch disk backwards.... if so, the disk hub is torqued against the crankshaft hub preventing engagement of the clutch. 2003 TIBUORN DUAL MASS FLYWHEEL AND CLUTCH DISC ASSEMBLY INSTALLATION PROCEDURE DESCRIPTION: The 2003 MY 2.7L Tiburon vehicle equipped with the 6-speed manual transaxle employs a dual mass flywheel system. The 2003 Tiburon Shop Manual does not show the clutch disc assembly with the dual mass flywheel. This bulletin provides information about how to assemble these components. NOTE Although it is possible to assemble the clutch disc with either side facing the flywheel surface, only the assembly of these two parts shown in this bulletin is correct.
  1. Attach the dual mass flywheel to the engine crankshaft assembly.
  2. Identify the clutch disc flange side and the collar side as shown. 0240025a.gif
  3. Install the collar side of the clutch disc on the dual mass flywheel surface so that the flange side is facing the pressure plate side as shown. 0240025b.gif
  4. Attach the pressure plate to the dual mass flywheel and complete assembly of the remaining components per the Shop Manual procedures. 0240025c.gif

Dec 14, 2008 | 2004 Hyundai Tiburon

Not finding what you are looking for?
2002 Hyundai Santa Fe Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts


Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides