Question about 1994 Isuzu Rodeo

1 Answer

1996 isuzu rodeo- flasher and signals not working- need to locate wher the flasher relay goes (fuse?)

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 57 Answers

SHOULD BE IN THE FUSE BOX

Posted on Jul 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the dash light fuse for a 1996 Isuzu


The flasher or dash light fuses are under the dash next to the drivers left knee above the side panel. Hope this helps.

Oct 16, 2014 | 1996 Isuzu Rodeo

1 Answer

Locating flasher relay on a 2000 isuzu rodeo 4wd


under the hood in fuse box or under the dash on firewall. if not there take the drivers side kick panel off

Aug 17, 2012 | Isuzu Rodeo Cars & Trucks

1 Answer

Where is the hazard and flasher relay in the 1996 isuzu rodeo? Hazards and signals are not working, all new bulbs and fuses, still nothing, can't find the relay


The relay should be located inside the vehicle on the drivers side, under the dash right above the kick panel. below is a picture of what it will look like but yours may be a different color but the shape should be the same. I hope this helps and good luck.


clifford224_236.jpg

May 22, 2011 | 1996 Isuzu Rodeo

2 Answers

1993 rodeo not running no power to fuel pump


if there is no power to the fuel pump check relays and fuses....UNDERHOOD FUSE & RELAY PANEL IDENTIFICATION Fig. 2: Underhood Fuse & Relay Panel Identification Courtesy of ISUZU MOTOR CO. Fusible Link Identification ? A - 80 Amp (1991-92 3.1L) ? A - 60 Amp Main-1 ? B - 30 Amp Main-2 ? C - 30 Amp (1993-94) ECM (3.2L) ? D - 30 Amp Condenser Fan (A/T Models) Relay Identification ? 1 - Headlight Relay ? 2 - A/C - Heater Relay ? 3 - Starter Relay ? 4 - A/C Compressor Relay ? 5 - Charge Relay ? 6 - Fuel Pump Relay ? 7 - ECM Relay ? 8 - Wiper Relay Fuse & Circuit Breaker Identification ? 1 - 15 Amp (1991) ECM, Fuel Injection System ? 1 - 15 Amp (1992-94 2.6L) ECM, Fuel Injection System ? 1 - 10 Amp (1992-94 3.1 & 3.2L) Heated Oxygen Sensor, Fuel Injection System ? 2 - 20 Amp (1991-92) Fuel Pump ? 2 - 20 Amp (1993-94 2.6L) Fuel Pump ? 2 - 15 Amp (1993-94 3.2L) Fuel Pump ? 3 - 10 Amp (1991) ? 3 - 15 Amp (1992-94) Turn Signal Lights, Hazard Warning Flasher Lights ? 4 - 10 Amp Horn, Door Locks ? 5 - Not Used (1991 3.1L) ? 5 - 10 Amp Charging System, Charge Warning Light WARNING: Always disconnect battery ground cable before servicing "high- current fuses. It is recommended that "high-current" fuses be replaced by a qualified technician. Page 1 of 2 FUSES & CIRCUIT BREAKERS -1994 Isuzu Rodeo LS? 6 - Not Used (1991) (1992-93 2.6L) ? 6 - 10 Amp (1992-94 3.1L & 3.2L) A/T Interlock System ? 6 - 10 Amp (1994 2.6L) Heated Oxygen Sensor, Fuel Injection System ? 7 - 20 Amp Heater/Air Conditioning Blower Controls ? 8 - 10 Amp Air Conditioner Compressor Controls ? 9 - 10 Amp Right Headlight ? 10 - 10 Amp Left Headlight © 2008 Mitchell Repair Information Co., LLC.
62217_isuzfuse_1.jpg
Underhood fuse block swap out relay #7 thats the ECM relay.
Ground Circuits Using a DVOM, touch negative voltmeter lead to a good ground. Touch positive voltmeter lead to each ground terminal. With vehicle running, voltmeter should indicate less than one volt. If reading is greater than one volt, check for open, corrosion and loose connection on ground lead. See ECM GROUND LOCATION table for ECM ground location.
Page 1 of 1 SYSTEM/COMPONENT TESTS - 2.6L EFI -1994 Isuzu Rodeo

Mar 28, 2010 | 1993 Isuzu Rodeo

1 Answer

'94 Rodeo right turn signals not working unless using hazards


sounds like a switch problem in the steering colum, could be a bad switch could be a loose connection. my advice would be to purchase a auto repair manual for you vehicle for detailed instruction on testing and/or replacing the switch.

Feb 14, 2010 | 1996 Isuzu Rodeo

1 Answer

I want to replace the turn signal relay.


the flasher for the signals is under the dash by drivers right foot, also look at the fuse panel on left end of the dash......

Jun 15, 2009 | 1996 Isuzu Rodeo

1 Answer

Turn signals/ flasher don't work


it's called a flasher relay and is either round and silver or black and square, you can pick it up for a couple of bucks at your local auto parts store. please rate this thanks

Sep 30, 2008 | 1993 Isuzu Rodeo

Not finding what you are looking for?
1994 Isuzu Rodeo Logo

Related Topics:

379 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...