Question about Cars & Trucks

1 Answer

Tried to to change brake pad in rear brake piston came out will not go in.

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

If it will not go in with the use of a c clamp replace the caliper then

Posted on Jul 12, 2010

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
alicantecoli
  • 22156 Answers

SOURCE: How do you change rear brake pads on 06 Malibu ?

get a nice pair of snap on water pump pliers and a G clamp .place G clamp on piston and apply slight pressure then turn piston with the water pump pliers ,better getting er indoors to tighten clamp very slowly whilst you support the caliper and wind the piston in at the same time.

Posted on Feb 08, 2009

morse008
  • 1111 Answers

SOURCE: reset piston on rear disc brakes 2008 Grand Caravan

they should screw in not compress

Posted on Aug 24, 2009

Testimonial: "Thanks--very helpful---fast response!"

alicantecoli
  • 22156 Answers

SOURCE: got an 05 smart forfour..having problems with the rear brake pads

both ,push in and turn at the same time ,difficult single handed but with a G clamp?? and snap on water pump pliers to turn it with its a fiddly job but not too difficult ,have you found your chassis number yet??? took me ages to find ---in the boot on the cross member under the floor

Posted on Sep 01, 2009

  • 1 Answer

SOURCE: changing the rear brakes on a 97 oldsmobile cutlass supreme

use a pair of pliers.put each side of the jaws of the pliers in one of the V-grooves of the piston and turn clockwise whle pushing it in

Posted on Nov 04, 2009

tneubauer
  • 437 Answers

SOURCE: changed frt and rear brake

The piston must be rotated as it is pushed into the caliper. There is a special tool for this that is sold at just about all parts houses. The tool looks like a small square with various pins for various applications that goes on the end of your 3/8 drive ratchet.

Posted on Feb 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I removed the rotor and brake pads. but when going to change the pads I can not get the piston to go back far enough to put the new ones in. How do you get the piston to push back in order to put the brake...


You will have to use a c-clamp or brake piston compressing tool to get that piston back in, while you have the brake master cylinder fluid reservoir cap off.

Sep 14, 2011 | 1999 Ford Taurus

1 Answer

I want to change my front brake pads How do I remove the old ones


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!!
For front brake pads. You should buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Apr 12, 2011 | Volkswagen Polo Cars & Trucks

1 Answer

Anything special about changing front pads on audi a3? I've done honda, acura and toyota's.


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!! For front brake pads. For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow: 1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose! 2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper. 3. Now you must thoroughly clean the brake calipers (free of grease). 4. Remove outer brake pad from brake carrier. 5. Pull inner brake pad out of brake caliper piston. 6. Check up the brake fluid level on the reservor, and emptying if neccessary! 7. Push piston back into brake caliper housing. 8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward). 9. Install outer brake pad into brake carrier. 10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm. 11. Install both caps. 12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Aug 25, 2010 | 2007 Audi A3

3 Answers

How do i change the brake pads on a 2005 grand prix pontiac


remove the caliper, by removing the two holding bolts, then use a old brake pad against the pistons and a c clamp and push piston all the way in, next is to clean and lube pad mounting surface and the caliper slide pin, then install new pads on bracket then caliper and tighten caliper bolts, heres a diagram to help you,98c6b31.jpg150490f.jpg

Apr 16, 2010 | 2005 Pontiac Grand Prix

1 Answer

Changing rear brake pads


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also.
But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!!
For front brake pads. First you must verify yours front brake disc diameter: 280 mm or 288 mm. (On my car y have 288 mm). After that you can buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Please rate my response. Thanks!

Apr 09, 2010 | 1999 Volkswagen Passat

1 Answer

I changed rear brake pads now breaks are sticking in the rear of my 2000 jimmy


strip them out again clean the claibers so the new pads slide freely grees with copper grees the pins and stick a spot on the back of the brake pads that sit on the brake pistons,,,not the disk!!! and check the brake pistons are free to move,,you should be able to just push the brake pistons back into the cylinders with your thum only,,,

Feb 08, 2010 | 2000 GMC Jimmy

2 Answers

Rear brakes pistons not retracting


try screwing it in turn a set of pliers around put handle in, in the piston there are indents in the bottom

hope2help shack

Apr 18, 2009 | Mitsubishi Mirage Cars & Trucks

1 Answer

Changing the rear brake pads on 91 mu


Chalk the front wheels, car is on jackstands i hope, release the handbrake, use the old pad with a c- clamp to compress the pistion on the caliper, install new pads. may have to take the cap off the master cylinder, if none of this works, open the bleeder valve, and compress the piston, rebleed the caliper.

Feb 24, 2009 | 1995 Isuzu Rodeo

1 Answer

Rear brake calipers


A big pair of channel locks will collaspe the caliper but it does take some muscle or you can release the brake line nut and releave the pressure but then you would have to bleed the brakes.

Aug 03, 2008 | 1990 Honda Prelude

1 Answer

Mitsubishi Montereo - Rear Brake pads


you must spread the pads out....do this with a wedge-shaped tool and use lever action to push the caliper pistons back to the fully-retracted positions in the cylinders. The pistons are currently in the position where the last pads had allowed them to extend to. It is good practice to (excercise) the pistons at pad change time by moving the pistons back and forth slowly to remove any oxidation at the cylinder walls, but never allow pistons to fully extend...prevent this by using a piece of wood to act as the thickness of one rotor and 2 pads. You extend the pistons by using the car's brake pedal, then retract them with the wedge.

Jun 07, 2008 | 2000 Mitsubishi Montero

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...