Question about 1997 GMC Sierra

1 Answer

Need to find relay censor convertor torque

Having some problems with transmission. I have changed everything. Looks like one sensor is missing but cant find it. Has to do with relay censor torque converter. Not sure where it is so i can change it.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,669 Answers

What kind of problem are you having with the transmission? I'm asking because there is no relay sensor for the torque converter clutch.

Posted on Jul 12, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

98 jeep codes p0743,p0740


Go here - www.jeepforum.com/forum/f11/tech-faq-links-tsbs-89273/ - and find the AW-4 Service and Diagnostic Manual. Looks like you need to test some solenoids.

P0740 (M)Torq Con Clutch, No RPM Drop at Lockup. Relationship between engineicon1.png and vehicleicon1.png speeds indicated failure of torqueicon1.png convertor clutch lock-up system (TCC/PTU solenoid)
P0743 (M)Torque Converter Clutch Solenoid/ Trans Relay Circuits. An open or shorted condition detected in the torque convertor clutch (part throttle unlock) solenoid control circuit. Shift solenoid C electrical fault - Asin transmissionicon1.png
P0743 (M)Torque Converter Clutch Solenoid/ Trans Relay Circuits. An open or shorted condition detected in the torque convertor part throttle unlock solenoid control circuit (3 or 4-speedicon1.png autoicon1.png. trans. only).__________________
.
Rather than banning scary looking black semi-automatic sporting firearms, why don't we
identify and treat the nut jobs pulling the triggers, and put the criminals in jail ?

Feb 11, 2013 | 1996 Plymouth Voyager

1 Answer

I have a 1990 chevy beretta which is hesitating to start & also as you are going down the road you can feel it missing or cutting out. then it also dies when you stop at a redlight. the crank sensor...


transmission torque convertor solenoid is bad locking the transmission and stahling the engineout unplug the harness on the transmission ull be fine ... 4 the stahling and missing while in park u might have faulty fuel injectors

Sep 19, 2011 | 1990 Chevrolet Beretta

1 Answer

I can't seem to get my motor and transmission to bolt back together theirs about a half inch between them what am I doing wrong please help anyone Its a 95 Pontiac bonneville I'm having the problem...


When you get ready to bolt the transmission back to the engine, you have to make sure that the torque convertor is seated all the way into the transmission. With the transmission and engine put together there should be about 1/2 inch between the flywheel (flexplate) and the torque convertor. It should also spin freely. If not then you might not have the convertor all the way in the trans.

Jun 28, 2011 | 1992 Cadillac Eldorado

1 Answer

I was driving today in my 2004 Ford Freestar van when all of a sudden the transmission stopped being engaged. I pulled over, no problem with the moter, but it would not slip back into drive reverse etc. No...


I have seen a problem with torque convertors on these vehicles, they will just all the sudden neutral out and that is it no noise no codes nothing... alot of times depending on the failure of the convertor just the convertor can be changed.... what usually happens is the splines inside of the convertor sheer off and once a new convertor is put in everything is back to normal.

May 27, 2011 | Ford Freestar Cars & Trucks

2 Answers

98 SW wagon starts fine but stalls out when put into drive or reverse. Code P0743 comes up after diagnostic check. Says Torque Converter Circuit is open. How do I go about fixing this?


I was definitely gonna say your torque converter. The fix is to replace your torque converter. The convertor basically transfers the moving motion from the engine to the non moving motion of your transmission smoothly. When it goes bad it will usually make the motor run rough in gear or stall the motor when it's completely bad. It will be a fairly expensive cost since the torque convertor sits between the engine and transmission. It also could be faulty wiring as well. You would have to have it physically diagnosed by a mechanic to confirm if its electrical or the actual torque convertor.

May 14, 2011 | 1998 Saturn SW

1 Answer

What causes the car to be unable to switch gear, and how can I resolve that problem?


Fluid, transmission fluid,especially the right type,For a electronic controlled transmission, youll need to check the engine control and engine computer for proper operation there are many sensor that provide input to the transmission control. Heres some mechanical the torque convertor,must be able to push fluid out, the transmission oil pump must be able to supply the torque convertor and give proper pressure,for valves to operate,then there are the gears,that has to transfer power.Okay lets keep it simple there is a PRNDL switch that can fail and it wont allow a gear change, Then there is TPS throttle position sensor that allows the gear change,then and output speed sensor that allows a gear change.There are factor that contribute to proper gear change and there all simple, First and foremost it fluid check fluid condition is it foaming, its a seal problem, is it pink its contaminated,is it burnt, (black) the clutches are worn.

Apr 23, 2011 | Chrysler 300 Cars & Trucks

1 Answer

I'm having trouble getting my transmission to go back flush with the engine.


torque convertor is not in all the way there is one little half inch thats hard to get the convertor to set in, best bet take break have a beer, go back at it and the torque convertor will slip right on

Oct 29, 2010 | 1997 Ford Explorer AWD

1 Answer

Wont start i put crank sensor on


If the crank sensor gets its signal from the torque convertor,the convertor has to go in the same way it came out,as the pickup for sensor is on the convertor...good luck...lee

Nov 06, 2009 | 2000 Saturn SL

2 Answers

1998 Chevrolet Cavalier, automatic transmission. Engine light comes on and then when car shifts gears, it shifts very rough. Took it to a mechanic and it wasn't reading any codes. Had car serviced and...


A vacuum leak somewhere, or a tranny modulator, or both. Mechanic can do a vacuum test, or you can buy the vacuum meter and do it yourself. transmissin modulator (if your car uses one, that is) is located on the outside of the tranny and looks like a frisbee-shaped disk about the size of the base of a water glass, made of aluminum, and has a vacuum hose attached. buy at a parts store. (I'm betting on a vacuum leak, though)

Aug 06, 2009 | 2005 Chevrolet Monte Carlo

Not finding what you are looking for?
1997 GMC Sierra Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...