Question about Cars & Trucks

Open Question

How do I replace a brake light switch on a 98 Mazda 626?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 110 Answers

SOURCE: 1999 mazda 626 no brake lights

TRY BRAKE SWITCH

Posted on Nov 17, 2008

CRTN
  • 716 Answers

SOURCE: changing the tail light bulbs on a 2000 mazda 626

The Tail Lights Are Accessed From The Inside Of The Trunk There Will Either Be A Panel Immediately Behind Where The Light Is Or Carpet. Remove It And It Will Give You Access To The Rear Of The Bolts Just Grab Twist And Pull And The Light Will Come Out.

Posted on Jan 26, 2009

MNfisherman
  • 11896 Answers

SOURCE: 98 Mazda 626 Won't Crank, Won't Jumpstart, no power on anything

Either one of your cables isn't getting a good enought contact on the battery or solenoid, or the solenoid is bad, or relay for starter is bad.

Posted on Jan 29, 2009

  • 2 Answers

SOURCE: 2000 Mazda 626 brake lights

It may be the switch on the brake pedal, it should be located on top of the brake pedal arn.

Posted on Apr 08, 2009

  • 297 Answers

SOURCE: 1999 Mazda 626 no rear lights!

fuse or wire harness, checked the voltage present in the fittings? Switch on before checking.
you get 12 volts more or less?

Posted on Apr 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No stop lights 2001 626 mazda


check for a blown fuse,blown bulbs,or the brake light switch which is located behind the brake pedal.

Sep 10, 2012 | 2001 Mazda 626

1 Answer

1998 Mazda 626 How to replace Break Light Switch


The brake light switch is located behind the brake pedal. To replace the brake light switch, first disconnect wire couplink ,next unscrew the switch from behind the bracket. You will see a locknut holding it in place.Remove the lock nut and the brake light switch will come out easily. After replacing the brake light switch make sure that when the break pedal is in released position that the buton on the switch is pressed in. you may have to ajust the switch position to achieve this goal. Thanks. you can rate this solution and show your appreciation.

May 19, 2010 | 2000 Mazda 626

1 Answer

ABS brakes not working


If you can feel the pedal pulsating and the light turns on the Abs is doin its job. if you want a better stop you could try a brake pad upgrade to ceramic pads and for even more stoping power add an after market drilled and sloted rotors.

Feb 28, 2010 | 1998 Mazda 626

2 Answers

Mazda 626 1991 back brake ligths not working


Is the fuse for the brake lights OK?
Check for power to the brake light switch at the brake pedal and for power coming from it with brake pedal depressed.

Sep 06, 2009 | 1991 Mazda 626

2 Answers

My 99 Mazda Brake lights stopped working


Check the ground to the brake light socket. I had a similar problem on a 98 626 and found the ground connector corroded in the socket.(it is on the outside of the socket between the metal insert and plastic housing) Pulled the remnants of the connector out far enough to solder a piece of wire onto it and then soldered it to the metal socket. Lights started functioning normally again. It seems that a bad ground on one socket affects every light in the circuit.

Jun 06, 2009 | 1998 Mazda 626

1 Answer

No headlights when turned on


Just a thought. I have a 98 626 5 speed. When the hand brake is applied the head lights go out but the marker lights stay on. Might be a switch issue with the hand brake...worth a look. The sensor should be located at the pivot point for the brake handle.

Feb 02, 2009 | 1998 Mazda 626

1 Answer

Electrical issues


the lights are probably wired through the radio my blazer is like that you will need a wiring diagram of the radio and the lights to figure it out

Nov 17, 2008 | 1998 Mazda 626

2 Answers

2000 Mazda 626 brake lights


try brake light switch on top of brake peddle

Sep 13, 2008 | 2000 Mazda 626

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...