Question about 1996 Ford Explorer

1 Answer

1996 FORD EXPLORER , MISS FIRE ON CYL # 2, 1ST REPLACED PLUGS AND WIRES, THEN THE COIL PACK AND LAST THE FUEL INJECTOR BUT PROBLEM STILL THERE, ANY HELP WOULD BE GREAT

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,826 Answers

OK,
Have you tried the following:


Ignition Control Module (ICM) REMOVAL & INSTALLATION NOTE: Only the EEC-IV ignition systems use an external ICM. EEC-V systems have incorperated the ICM into the Power Control Module (PCM).

  1. Disconnect the negative battery cable.
  2. Detach the wiring harness connector(s) from the ICM.
  3. Remove the mounting bolts, then remove the ICM. To install:
  4. Position the ICM onto the inner fender apron and install the mounting bolts. Tighten the bolts to 22–31 inch lbs (2.5–3.5 Nm).
  5. Attach the wiring harness connector(s) to the ICM.
  6. Connect the negative battery cable. Fig. 1: Ignition control module and mounting location on the 2.3L, 2.5L engine 1996 FORD EXPLORER , MISS - 89682g32.gif
    Fig. 2: Ignition control module used on all EEC-IV systems except the 2.3L engine 89682g33.gif
    Fig. 3: Ignition control module mounting on all EEC-IV systems except the 2.3L engine 89682g34.gif
prev.gif next.gif

Posted on Jul 11, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 honda civic EXcheck engine light code miss fire cyl 1 new fuel pump new plugs coil packs running lean need help mike


Change the #1 fuel injector to #2 and #2 to #1 position.If the miss fire code changes to #2 cyl that fuel injector may need to be changed.I would try that first before spending $$$

Apr 20, 2017 | Honda Cars & Trucks

1 Answer

Misfire coil


coil pack voltage may be good but coil may not be putting out voltage check with spark checker.also fuel injector may be bad if all good do compresson test on cyl

Apr 16, 2014 | 1998 Ford Expedition

2 Answers

92 explorer sport missing at idol and acceleration


The 1st thing to replace is the plugs and plug wires, they are goood for about 100,000 miles, then if that doesn't do it you may have more serious concern. issues

Feb 11, 2012 | 1992 Ford Explorer

2 Answers

Blinking engine light,cylinder 6 misfiring,sputtering , changed w


i would deffently try the carburator cleaner trick then odds are its a vacum problem. also just asking before having replaced the fuel injector on that cyl. did you or the shop use a noide light to make sure it had injector pluse on that fuel injector wiring plug.

Mar 11, 2010 | 1998 Ford Windstar

4 Answers

I have a ford explorer 99 but it's giving a error code PO306 what do u think it is


It sounds like a misfire. Check spark plugs 5 and 6. It could be bad fuel, bad plug wire, or weak coil. Check the fuel injectors as well. Other possible causes could be an egr valve stuck open, vacuum leaks, low fuel pressure.

Feb 17, 2010 | 1999 Ford Explorer

3 Answers

99 dodge caravan #4 cylinder misfires, i replaced spark plug wires and spark plugs. Scanner showed #4 still misfiring, could this be the coil?


It could very well be a bad coil pack,or you have low compression in that cylinder.If the compression is good then go with the coil pack,if not you may need a head gasket or an intake manifold gasket.

Nov 07, 2009 | 1999 Dodge Grand Caravan

2 Answers

2002 Ford Tarus intermittant missing cyl #3 after tuneup


I would remove one plug at a time, plug it back in wire and lay on top of engine block. Have some one crank and look for spark. Do this for each plug. If 1 is missing. You have bad wire. If two sparks are missing, then you have bad coil pack, if 3 is missing, you have two bad packs or bad module, if all cylinders are missing, then module or cranks sensor is faulty. Dont forge to change those plug wires just as often as plugs. They may look good still, but they get weak

Sep 11, 2009 | 2002 Ford Taurus

2 Answers

2001 ford taurus p0301 and p0303


You are mis fireing on cyl 1 and 3 if you replaced plugs and wires and coil this is going to be a fuel injector issue or valve issue. See if you can swap the injectors with known good cyl. and see if it changes. Or have a shop do a fuel injector service on it to see if it helps. It may be to late for the fuel injector service.

Mar 01, 2009 | 2001 Ford Taurus

1 Answer

04 explorer running bad


If this is a coil pack ignition system (no spark plug wires, just a coil pack on each plug), this sounds like you may have a coil pack that is going bad. Do you have a check engine light on? You might also think about having someone take a look at your fuel injectors, if one or more isn't firing this will cause a miss that will sometimes seem like a faulty spark plug. Hope this helps.

Feb 19, 2009 | 2004 Ford Explorer

Not finding what you are looking for?
1996 Ford Explorer Logo

438 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...