Question about 1992 Ford Ranger

1 Answer

I have a 92 ranger V6 3.0 automatic and when i drive it sometimes the check engine light will come on and while im driving, the truck will accelerate and decelerate over and over and most of the time when i push the gas pedal all the way to the floor for a second, the problem goes away. what could this be?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 469 Answers

Check to see of the tank is vented properly.

Posted on Jan 04, 2018

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 653 Answers

SOURCE: 2002 ford Ranger 3.0 v6 (auto) rear end noise when accelerating on curves.

Grab the bed of the truck and vigorously rock the vehicle from side to side. If you hear clunking in the axle, you probably need to check the carrier bearings in the differential. I had the carrier bearings, wheel bearings, and seals replaced in my mother-in-law's 1991 Ranger for $280, and it rides like a new truck. Well, ok, it rides like an 18 year old truck with a new rear end. I provided the wheel bearings and seals to the shop, and they provided the carrier bearing, lube, and labor. While the axles are out, check the surface where the axles ride on the bearings. If they are worn, there are undersized bearing available, but it is usually cheaper and easier to just by new axles.

Posted on Feb 12, 2009

  • 1 Answer

SOURCE: 1997 Ford Ranger 3.0 Automatic Timing Belt or Chain?

both

Posted on Apr 16, 2009

co7196
  • 3433 Answers

SOURCE: how to bleed hydraulic clutch on 92 ford ranger

If there is no bleedr, the loosen the lie and get fluid to at lest that point. The bleeder, not having onwe is unlikely, no offemce, just make sure. If the bleeder is anywhere it dhould or would be at a point higher than the line on the slave cylinder down on the bell housing. Open it and let gravity takr over unti the fluid drips steasdy. Slowly depress clutch once to get fluid moving.If long term non usem The cylinders, master and slave, good luck may have leakage needing replacement.l good luc and be careful. be sure brakes are set and vehicle is in neutral when underneath. Engine need not be running.

Posted on May 14, 2009

  • 54 Answers

SOURCE: when push gas pedal, oil pressure goes up

have you oil pressure sending unit checke/replaced

Posted on May 26, 2009

  • 63 Answers

SOURCE: 1994 ford ranger 2.8 v6 engine automatic 4 wheel

That could Be caused by the TFI module Located on the side of the distributor its grey module that requires a special tool to remove the two screws

Posted on Aug 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

92 ford ranger wont start


how old is the battery get it checked and make sure the connections at the the battery and the terminal on the stsrter pos. post are tight. find the grd term on the engine and make sure every thing is good and tight

Dec 17, 2012 | 1992 Ford Ranger

1 Answer

My isuzu is 1998 bighorn.the problem is check engine light come on aand engine stops.i have to start it again


i had a similar problem with my pt cruiser, check the battery terminals sometimes its just a bad connection, you may need to buy new terminals, only ten dollars maybe

Jun 15, 2012 | 1998 Isuzu Trooper

1 Answer

92 honda accord lx auto trans has been shifting around 2,500-3,000 rpm each gear and now the D4 gear does not work at all and D3 works but accelerates slowly after a complete stop. i have to shift down...


check transmission fluid level- run/drive for about 10 min. , park car- check with engine running- add fluid if needed- ,if fluid NOT low- transmission filter needs to be changed

May 10, 2011 | 1992 Honda Accord

2 Answers

I have a 1999 ford ranger 2 wheel drive automatic


Sometimes this works, ABS light on, check engine light on, speedometer not working, and the automatics start shifting hard or not shifting at all? One bolt and the part is cheap, its weird how one part controls so much.

Mar 10, 2010 | 1999 Ford Ranger SuperCab

3 Answers

My 2004 automatic ford ranger shifts hard


The tranny problem sounds like it is out of fluid hopefully, or more likely the shift solenoid, and clutch packs are sticking and that requires a rebuild. The "almost misfire" sound like a clogged injector just pour son injector cleaner in there. I recommend using a brand called PowerService "DieselClean" you can get it almost anywhere. As for the dying , I had an 04 danger ranger and mine would shut down while I was driving and i had to pull over and push the fuel system manual override "which is a button under the passenger side dash" and then it would start again. I was never able to figure that one out.

Feb 21, 2010 | 2004 Ford Ranger

1 Answer

2002 Ford Ranger transmission slipping?


The longer you drive with that condition, the more damage you will cause. Park it until you can repair it.

Think of it as how long would you think it is okay to run your engine without oil? Zero.

Doc

Sep 14, 2009 | 2002 Ford Ranger Regular Cab

1 Answer

Sputtering while driving


try a tune up-plugs and wires-and air filter

Apr 22, 2009 | 1992 Buick Roadmaster

3 Answers

Hesitation on Acceleration or Uphill.


The knock is caused by either timing issue or a lean cylinder condition, have you checked the fuel pressure?? has the fuel filter been changed?? A bad knock sensor will not set a light unless it is open or disconnected.

Aug 19, 2008 | 1992 Buick LeSabre

Not finding what you are looking for?
1992 Ford Ranger Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

83036 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

gerry bissi

Level 3 Expert

4387 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...