Question about 1994 Toyota Corolla

1 Answer

Timing belt crankshft postioning

I want to find the exact position for the crankshft to replace the timing belt

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 97 Answers

The little dot on the crankshaft sprocket has to be aiming staight up and you will also need to remove the #1 spark plug to make sure the piston is at top dead center.you can check if it is all the way up by using a long,thin screwdriver and putting it in the spark plug hole.if the piston is not all the way up.you will need to turn the crankshaft 1 whole turn clockwise and stop when the dot on the sprocket is aiming up agin.the piston should now be at top dead center.i hope this information helps.take care and good luck, manny

Posted on Jul 11, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

97 honda accord changed timing belt and crank case sensors replaced them now car turnes over fires gets gas but wont crank


check to make sure that the crankshft and cam gears were lined up correctly with # 1 cyl at top dead center.

Jul 08, 2012 | 1997 Honda Accord

1 Answer

How to install timing belt


One way to do it, is to make a mark on the tooth wheels the timing belts is running over, and a correspondig mark on somewhere on the engine.
Another way is to turn the tooth wheels around, until the factory made position marks on the tooth wheels correspond with the factory made position marks on the engine (normally upper part).
What is important is that the tooth wheels are in exactly same postion when you put on the new timing belt, as when you removed the old timing belt.
It's also recommended to replace the unit used for tightening the timing belt at the same time.
This is only a short description of the most important things. For a more detailed describtion, one can get a repair manual from Haynes: http://www.haynes.com/products/productID/208

Aug 18, 2010 | 1990 Volvo 740

1 Answer

The timing belt on my 86 Civic will not turn, what could be a few causes for this?


if engine turns but belt does not the teeth on the belt will probably be stripped at crankshft gear, remove belt to inspect. most likely this will have caused engine damage

Apr 26, 2010 | 1986 Honda Civic

2 Answers

How do i get slack in timing belt on 2.4 plymouth


if you are going to replace the belt ,there is a tention pully that yiu needs to be loosend spend the 20.00 dollors for a manuel at tour local parts stor becouse you need to make sure to keep the cam and crankshft alined when re installing belt

Jan 07, 2010 | 1996 Plymouth Voyager

1 Answer

2003 hynudia accent timingbelt replacement


yes those are the marks and it sounds like its not in timing

Jan 25, 2009 | 2000 Hyundai Accent

1 Answer

Camshaft


Most likely yes. It's not that the cam is out of position (that's controlled by the timing belt, so as long as the belt hasn't slipped, the cam is where it should be). What's more likely is that the cam sensor has gone bad, as you're suggesting, and it's not able to tell the computer the position of the cam, or it's telling the computer that the cam is in a position that the computer knows it can't be.

Replace the cam sensor and you'll be fine.

Aug 30, 2008 | 1999 Hyundai Sonata

2 Answers

Won't start


try changing out the crankshft positioning sensor it get fire to everything.your starter could also have gone out

Aug 20, 2008 | 1997 Nissan Quest

1 Answer

How to time a dohc 3.4 1995 monte had broken belt thanks


HI...
TO set timing belt. on a 3.4 95 chevy.
you need to remove the VALVE Covers.
at the and of the camshafts, you will see grove.
In the grove you need to put a metal flat piece croosing both of the cams. to lock on position.
and put the timing mark on the crankshft pulley ore sproket.

OK.. I hope this help on your question.
Thank you for use fixya.

Jul 30, 2008 | Chevrolet Monte Carlo Cars & Trucks

Not finding what you are looking for?
1994 Toyota Corolla Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...