Question about 1999 Kia Sportage

2 Answers

Cylinderhead torque stc. - 1999 Kia Sportage

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Kia Master
  • 6,826 Answers

Cylinder Head Removal & Installation SOHC To Remove:

  1. Relieve fuel system pressure.
  2. Remove timing belt cover. Camshaft timing marks cylinderhead torque stc. - kia-03-20-7032.gif

  3. Turn crankshaft until timing mark on front housing and the arrow "2" on the camshaft pulley align.
  4. Loosen lock bolt on tensioner.
  5. Pry tensioner away from timing belt and tighten lock bolt to relieve tension on the timing belt.
  6. Remove timing belt from camshaft pulley.
  7. Disconnect battery negative cable.
  8. Remove 3 bolts that secure accelerator cable and air intake hose to cylinder head cover.
  9. Detach accelerator cable and place off to side.
  10. Remove the following;
    • Air hose
    • Air ISC air hose
    • Breather hose
    • Vacuum hose from air intake hose
  11. Disconnect mass air flow sensor electrical connector.
  12. Remove air intake hose.
  13. Remove PCV valve from cylinder head cover.
  14. Remove ISC air hose from idle speed actuator.
  15. Remove air hose from behind intake manifold.
  16. Remove 2 screws from high tension wire protectors.
  17. Detach wire loom from holder at rear of cylinder head cover.
  18. Detach vacuum tube at rear of cylinder head cover.
  19. Remove vacuum pipe. Cylinder Head Cover kia-03-20-7042.gif

  20. Remove 7 cylinder head cover bolts.
  21. Remove cylinder head cover and gasket.
  22. Disconnect 2 ignition coil electrical connectors.
  23. Disconnect 2 fuel injection electrical connectors at rear of cylinder head.
  24. Disconnect the following electrical connectors;
    • Oxygen sensor
    • Throttle position sensor
    • Idle speed actuator
    • Oil pressure switch
    • EGR vacuum solenoid valve at intake manifold
  25. Disconnect heater hose from elbow.
  26. Disconnect brake booster vacuum hose and cruise control vacuum hose from surge tank.
  27. Detach wire harness from rear of cylinder head.
  28. Disconnect purge control solenoid vacuum hose from intake manifold.
  29. Disconnect fuel hose from fuel connector assembly.
  30. Remove grounding bracket.
  31. Remove 4 bolts and intake manifold bracket.
  32. Remove starter.
  33. Detach water bypass hose from bypass pipe.
  34. Disconnect water hoses from oil cooler.
  35. Disconnect fuel hose from fuel pipe.
  36. Remove exhaust manifold heat shield.
  37. Remove exhaust flange nuts and front exhaust bracket bolt.
  38. Lower exhaust system. Cylinder head bolt loosening sequence kia-03-20-7050.gif

  39. Loosen cylinder head bolts in 3 steps in proper sequence.
  40. Remove cylinder head bolts and washers.
  41. Remove cylinder head, intake manifold and exhaust manifold as an assembly.
To Install:
  1. Install NEW cylinder head gasket.
  2. Install cylinder head, intake manifold and exhaust manifold as an assembly.
  3. Tighten cylinder head bolts in 3 steps in reverse sequence that was used during removal. Tighten bolts to 62 ft lb (84 Nm).
  4. Install front exhaust bracket bolt. Tighten bolt to 20 ft lb (27 Nm).
  5. Install NEW lower exhaust flange gasket and 3 nuts. Tighten nuts to 24 ft lb (31 Nm).
  6. Install exhaust manifold heat shield. Tighten nuts to 35 in lb (4 Nm).
  7. Connect fuel hose to pipe.
  8. Connect 2 hoses to oil cooler.
  9. Attach water bypass hose to bypass pipe.
  10. Install starter and bolts. Tighten bolts to 34 ft lb (46 Nm).
  11. Install intake manifolds bracket and 4 bolts. Tighten bolts to 32 ft lb (45 Nm).
  12. Install grounding bracket.
  13. Connect fuel hose to fuel connector assembly.
  14. Connect the following electrical connectors;
    • Oxygen sensor
    • Throttle position sensor
    • Idle speed actuator
    • Oil pressure switch
    • EGR vacuum solenoid valve at intake manifold
  15. Connect purge control solenoid vacuum hose to intake manifold.
  16. Attach wire harness from rear of cylinder head.
  17. Connect brake booster vacuum hose and cruise control vacuum hose to surge tank.
  18. Connect heater hose to elbow.
  19. Connect 2 fuel injection electrical connectors at rear of cylinder head.
  20. Connect 2 ignition coil electrical connectors.
  21. Install cylinder head cover.
  22. Install 7 cylinder head cover bolts. Tighten bolts to 60 in lb (7 Nm).
  23. Install vacuum pipe and 2 bolts at rear of cylinder head cover. Tighten bolts to 60 in lb (7 Nm).
  24. Connect vacuum tube to pipe.
  25. Connect loom holder to rear of cylinder head cover.
  26. Install 2 screws to high tension wire protectors.
  27. Install air hose to behind intake manifold.
  28. Install ISC air hose to idle speed actuator.
  29. Install PCV valve to cylinder head cover.
  30. Install air intake hose.
  31. Connect mass air flow sensor electrical connector.
  32. Install the following;
    • Air hose
    • Air ISC air hose
    • Breather hose
    • Vacuum hose from air intake hose
  33. Attach accelerator cable.
  34. Install 3 bolts that secure accelerator cable and air intake hose to cylinder head cover. Timing belt pulley timing marks

    NOTE: Timing belt pulley timing mark and timing mark must be aligned.
    Camshaft timing marks kia-03-20-7032.gif

    NOTE: The arrow at "2" on camshaft pulley must be aligned with timing mark on front housing.
  35. Install timing belt.
  36. Install timing belt cover.
  37. Pressurize fuel system.
  38. Start engine and check ignition timing.

Posted on Jul 11, 2010

  • Ron Austin Jan 31, 2011

    I was told that I needed to replace the head bolts with new ones as they would stretch. You did not mention doing this. Did I receive wrong information?

  • Duane Wong
    Duane Wong Jan 31, 2011

    It's probably a good idea to change the head bolts if you are afraid of this problem. However, I have changed cylinder heads before without changing the head bolts and it worked out fine.

×

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Kia Master
  • 6,826 Answers

I have a pdf file for the kia,if you need it,email me,I can not send it on here it is to large,roniecon@gmail.com, just rate me on here thank you.

Posted on Jul 11, 2010

  • Ronny Bennett Sr.
    Ronny Bennett Sr. Jul 11, 2010

    I have tried to send you what you need but can not on here,roniecon@gmail.com is my email,if you will email me,I will send you a whole pdf repair manual.

  • jesmith200 Aug 31, 2010

    can you send me the whole manual for a 1999 kia sportage or what ever you have.
    Thanks,
    JS

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

TORQUE SETTINGS


anyone want to guess on a MAKE, model ,engine size , year . I do not

Jun 24, 2016 | Cars & Trucks

1 Answer

Engine torque specs


NO Make No MODEl NO HELP SORRY

Nov 30, 2015 | Cars & Trucks

1 Answer

Hiya do you know the torque settings for cylinderhead for a bmw 525d e39 2002, 6 cylinder


Per BMW AG,
Jointing torque: 80 Nm
Loosen all bolts 1/2 turn
Jointing torque 50 Nm

http://www.adrianteo.com/files/cylinder-head-torque.pdf

Oct 05, 2014 | Cars & Trucks

1 Answer

Torque settings cylinder


There's no way to know unless you can tell us the make/model/year of the vehicle, and which engine it has. There are a thousand different engines, and they all have different cylinder head torque patterns & sequences.

Aug 12, 2014 | Cars & Trucks

1 Answer

CYLINDERHEAD BOLTS TORQUE SEQUENCE HYUNDAI ELANTRA


Install the gasket so that the surface with the identification mark faces toward the cylinder head.
Tighten the bolts to the specified torque in the sequence shown below.
b176b2ac-2453-4b5b-9b1d-0cb775cacffe.jpg

Aug 04, 2014 | 2001 Hyundai Elantra

1 Answer

Could you tell me the cylinderhead bolt torque for a 2003 mazda protege 2.0 litre engine with dual overhead cam and no turbo


First torque them in sequence to 13-16 ft.lbs.then in sequence to 85-95 degrees next do the same thing again torque to 85-95 degrees.

Jan 27, 2012 | Mazda Protege Cars & Trucks

1 Answer

I need the cylinderhead torque settings for 2004 1.3 city golf. Please assist


The head torque settings are 75 nm plus a further 90 degrees (102 ft/lbs)

The torquing sequence is:-

9 5 1 3 7
front
10 6 2 4 8

Mar 17, 2011 | Volkswagen Golf Cars & Trucks

1 Answer

I would to know the cylinderhead torque for a 3c 2.2 diesel


1st 48ft-lbf

2nd turn 90 degrees

3rd turn 90 degrees

Sep 09, 2009 | 1994 Toyota Previa

1 Answer

Cylinderhead bolts torque settings


According to my haynes manual for Landrover 200tdi, G - S reg,1989-1998 it goes as follows,
Stage 1:- Tighten all bolts to 30lb ft or 40Nm then
Stage 2:- Angle tighten a further 60 degrees then
Stage 3:- Angle tighten a further 60 degrees again.

Nov 29, 2008 | 1994 Land Rover Discovery

Not finding what you are looking for?
1999 Kia Sportage Logo

744 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76132 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...