Question about 2006 Suzuki Grand Vitara

1 Answer

Crankshaft pulley has the wobble not spinning in a even manner

Crankshaft pulley loose has the wobbles can see a fine metal dust on the outside of the pully if loose how do i tighten up

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Most likely the rubber part of the harmonic balancer has deteriorated causing the twin pulleys to separate. Tightening would not help if this is the case. A replacement would be needed.

Posted on Jan 06, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What could cause my crankshaft pulley to wobble if it just has the 1 bolt in the center of it holding it in

Year/make/model?? Check to see if bolt is loose. Some crank pulleys have a rubber insert that can seperate causing a wobble.

Mar 09, 2016 | Cars & Trucks

1 Answer

What could cause my crankshaft pulley to wobble on my v10 dodge 3500

Loose or missing attaching bolts. The bolt holding the pulley and the harmonic balancer to the crankshaft may be loose too.

Mar 09, 2016 | Dodge Cars & Trucks

1 Answer

Crankshaft Pulley wobbles on 1997 ford aspire

make sure the pulley bolt is tight then check the pulley for being bent. if these 2 things are good then you may have a bent crankshaft at the pulley end or worn crank bearing causing it to wobble.

Mar 01, 2015 | Ford Cars & Trucks

1 Answer

Pulley wobble on front of 1991 Mazda MX5 Miata engine with short nose crank

Hello, Unless Mazda forges the pulley onto the crankshaft, the pulley is usually a separate piece. You do not know which piece is bent and there may be a possibility that the pulley is coming loose attributing to the wobble.

Clearance is a big issue in working on these transverse mounted motors. You may possibly be able to get a socket on the crankshaft bolt to tighten it. Its a guess on whether there is enough room to switch the crankshaft pulley without dropping the engine cradle out of the body.

I can not say whether the crank bolt is a left or right handed thread. But with a little more research you may be able to find out. Use the Web Browser for a specific part search.

A site called is a Salvage network which links Salvage yards across the U.S. They have good contact info, price comparisions, and sometimes photos.

Jul 03, 2012 | Cars & Trucks

1 Answer

Loud rattling sound top of engine near or below the alternator when idling, goes away if accelerator is pressed

Hello: Remove the serpentine belt, see if the waterpump pulley wobbles/makes noise when you spin it. If thats not it then start the engine, belt still off see if noise is there also while engine is running see if vthe crankshaft pulley wobbles. Also check the A/C compressor pulley (engine off, belt off) spin it by hand and check for noise and wobble. If all the previous is ok then it could be the balance shaft front bearing and or the timing chain.

Oct 18, 2011 | 1998 Buick LeSabre

1 Answer

I have a 1994 Toyota camry xle 6cyl.,I started the car this morning and heard a whirring noise under the hood. Opened up the hood & the noise was coming from where the pulleys are .And had not heard...

Was the timing belt replaced recently? If your crank pulley/harmonic balancer is wobbling, it is probably loose. Do not run the engine, if this part falls out, it will cause more damage.

Sep 07, 2011 | Toyota Camry Cars & Trucks

1 Answer

Crankshaft pulley wobbled loose an alternator belt wont stay on...

dear friend-as this crankshaft pulley is cast iron it is impossible that it could be bent so you will have to remove it and look for damage inside the pulley and on the crankshaft,if this is not repaired the fanbelt will never stay on.

Jul 18, 2009 | 1991 Hyundai Sonata

Not finding what you are looking for?
2006 Suzuki Grand Vitara Logo

Related Topics:

319 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts


Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides