Question about Cars & Trucks

2 Answers

Hi I have a 2000 ford ranger 5 speed truck. I just replacd the clutch a few days ago. Is it normal for my gears to still be rough? Thanks.

Posted by Anonymous on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,793 Answers

Only if you didnt bleed the system fully or didnt adjust the cable correctly.(ive seen different systems fitted to the same make/model of car )

Posted on Jul 11, 2010

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 61 Answers

Sounds like the clutch needs to be adjusted

Posted on Jul 11, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ford ranger forum


throw out bearing might be bad

Jul 01, 2014 | 2004 Ford Ranger

1 Answer

Hi. My ford escort 97 lx wagon transmission is not shifting anymore it is stuck in first gear(althought if i put it in neutral while driving and switch back to drive it picks up for a few seconds...) and...


My brothers 2000 ford ranger the fuse went out to the speed sensor. I change the speed sensor because it did not shift out of 1st gear and the speedometer stopped working. I then found out the fuse was missing in the fuse panel. My brother could not tell where the fuse went but when I put a fuse in it started shifting and the speedometer started working. everything was good. You should have a code if it is the speed sensor.

Aug 14, 2017 | Ford Escort Cars & Trucks

1 Answer

About a month ago I began hearing rattling noises when I would depress the clutch. Over a few days the noise became less noticeable but then I started having trouble shifting gears (5 speed manual...


If the bearings were worn out due to high milage, the input shaft will have too much play in it. To replace all of the bearings is a big job, and a lot of shops won't do it. They may have replaced the transmission to save time, as replacing the bearing is very time consuming. So it all stems on what your final cost was.

Apr 13, 2010 | 2002 Ford Ranger Regular Cab

1 Answer

Hi I have a 2000 model ford ranger 2500 diesel


open the bleed screw on the slave cylinder ,whilst a good looking long legged assistant push the clutch pedal down and you open the bleed screw..If this still doesnt work then check the clutch arm trhow and see how much its moving ,could be you need a new master cylinder

Mar 17, 2010 | 2000 Ford Ranger SuperCab

1 Answer

2003 Ford Ranger-5 Speed. At times is very hard to get into gear


Your clutch is not releasing all the way. (Assuming the problem is not internal to the transmission) Bleed the system. If that doesn't work, rebuild the clutch master cylinder and slave cylinder and bleed again.

Aug 12, 2009 | 2003 Ford Ranger Regular Cab

1 Answer

2000 ford ranger 5 speed problems.


Your clutch disk and pressure plate and throw out bearing need to be replaced.

Jun 26, 2009 | 1989 Ford Ranger

2 Answers

Manual transmission problem


Change the fluid in the trans. If that dont work then your throwout is going bad and not disengaging clutch fully.

Apr 05, 2017 | 2000 Ford Mustang

1 Answer

1994 ford ranger extended cab 6 cyl fuel injected 2 wheel drive automatic


This year of ranger had a few flaws, In one case, a break power booster was robbing the vacumm, you can test this by plugging it off and seeing the differance, but you will have limited brakes. This model year had a problem with a vacuum leak on the manifold. You can check these in many ways, but please don't use starting fluid. The rear of the manifold usually on the drivers side where it seals to the block.
Also, in 2 other cases a cracked head has gave me the same problem. It is caused from a loss of vacuum.

Jan 01, 2009 | 1994 Ford Ranger Supercab

2 Answers

Ranger has 220,000 miles on it, runs great. Just started having difficulty getting it to go into gear (manual 5 speed. If I shift through the gears , it seems things line up adn then I'm able to get it...


HI,first i would check the lube in the tranny.Drain it in a clean container.So you can see how much metal shavings are in it.This will give you some kind of indication of the internals.Then look through the inspection hole to see if the pressure plate fingers are bent or any other clutch component damage.Good Luck!!!

Aug 04, 2008 | 1996 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...