Question about 2001 GMC Jimmy

1 Answer

My Ignition switch in steering column needs replacement. Can't turn key to on position for me to release the key cylinder out of the column. The shift is on the column.........note: Steering wheel is released.......how can I remove? Much Thanks, Wm.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 61 Answers

You need a steering wheel puller, you must remove the air bag first. dont forget to disconnect the battery .

Posted on Jul 11, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ignition switch 124 merc replace


Adjust the Mercedes telescoping steering wheel to the maximum extended position (maximum out position).
Move the front driver's seat to the rear-most position.
Disconnect the negative battery cable by loosening the retaining nut on the negative battery cable clamp and sliding the clamp off the battery terminal.
Remove the screws on the underside of the instrument panel cluster that hold the instrument cluster cowl in place and remove the cowl.
Remove the four screws holding the instrument cluster in place and remove the instrument cluster from the dash. Make sure to remove the electrical connectors from the back of the instrument cluster before trying to completely remove the cluster.
Turn the ignition key to the "I" position and remove the electrical plug in the back of the ignition switch. The switch should be exposed now that the cowl and instrument cluster have been removed. You will access the plug from the top of the ignition switch and cylinder assembly.
Loosen, but do not remove, the Allen bolt on top of the ignition cylinder that mates with the steering column using an Allen wrench.
Remove the two 13 mm bolts on top of the steering column. This will allow the steering column to drop down roughly 3 inches so that you can access the release button for the ignition switch.
Press the release button on the steering column where the ignition cylinder enters the column.
Turn the key to the "I" position and remove the ignition cylinder and switch assembly by pulling it out of the steering column.
Remove the ignition wiring from the back of the ignition switch and cylinder assembly by pressing down on the release tab on the electrical connector and pulling it off the switch.
Original Launch X431 iDiag Auto Diag Scanner for iPad and iPhone...

Aug 08, 2014 | Mercedes-Benz E-Class Cars & Trucks

1 Answer

Replace ignition switch on 99 jeep wrangler


The ignition key must be in the key cylinder for cylinder removal. The key cylinder must be removed first before removing ignition switch.REMOVAL 1. Disconnect negative battery cable at battery. 2. If equipped with an automatic transmission, place shifter in PARK position. 3. Rotate key to ON position.4. A release tang is located on bottom of key cylinder.5. Position a small screwdriver or pin punch into tang access hole on bottom of steering column lower cover.INSTALLATION 1. If equipped with an automatic transmission, place shifter in PARK position. 2. Position key cylinder into steering column as it would normally be in the ON position. 3. Press key cylinder into column until it snaps into position. 4. Check mechanical operation of switch. Automatic Transmission: Be sure transmission lever is locked in PARK position after key removal. If key is difficult to rotate or is difficult to remove, the shift lever-to-steering column cable may be out of adjustment or defective. If key can be removed, release lever mechanism may be defective. Release lever mechanism is not serviced separately. If repair is necessary, the steering column must be replaced. 5. Connect negative cable to battery. 6. Check electrical operation of switch. ab7076e7-9719-44a3-b66a-8584c6b2a3c1.jpg bfaa43e6-23a3-4771-9d95-55c2c3bf0a78.jpg

Apr 08, 2014 | 1999 Jeep Wrangler

1 Answer

How do I replace the turn signal multi-function switch in my 1998 Ford Expedition


SECTION 211-05: Steering Column Switches 1998 Expedition/Navigator Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 02/11/2000 Multifunction Switch Removal
  1. Disconnect the battery ground cable (14301).
  1. Remove the ignition switch lock cylinder (11582).
    1. Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
    1. Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.
    gj0845a.gif
  1. Twist the tilt wheel handle and shank (3F609) and remove.
    gj0846a.gif
  1. NOTE: Move gear selector to lowest position to access steering column opening cover.
    Release the four clips and remove the steering column opening cover.
    gj0847a.gif
  1. Remove the upper and lower steering column shrouds.
    1. Remove the three screws.
    1. Remove the lower steering column shroud.
    1. Remove the upper steering column shroud.
    gj0976a.gif
  1. Remove the multi function switch.
    1. Remove the two screws.
    1. Disconnect the electrical connectors.
    1. Remove the multi function switch.
    gj0848a.gif
Installation
  1. NOTE: When the battery (10655) is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
    To install, reverse the removal procedure.
    gj0850a.gif

2010&c18=modelyear&c20=n130593&c35=wsm%2cmultifunction%20switch%2cswj%2c211-05%2cremoval%20and%20installation&s=1366x768&c=32&j=1.3&v=y&k=y&bw=995&bh=405&ct=lan&hp=n&[aqe]

Mar 08, 2011 | 1998 Ford Expedition

1 Answer

Ignition switch would start but would not lock into position (RUN) and would shut off and then ignition completely locked down and will not move


The ignition key cylinder in a Buick unlocks the ignition and allows the Buick's engine to start. The cylinder contains a switch on the end of it (inside the cylinder) that sends an electric signal to the starter motor. When the ignition key cylinder fails, the Buick won't start. When this happens, you'll need a new ignition cylinder. Purchase replacement cylinders from Buick.
Difficulty: Moderately Easy
Things You'll Need:

  • Ignition key
  • Punch pin
  • Cross-point screwdriver
  1. 1 Remove the screws on the bottom of the steering column on your Buick. These screws hold the steering column cover on. You may need to tilt the steering wheel to its highest position to access these screws.
  2. 2 Turn the ignition key to the "II" position in the ignition cylinder.
  3. 3 Slide the punch pin into the access slot on the bottom of the ignition cylinder.
  4. 4 Push the pin all the way into the access slot while you pull the ignition cylinder out of the steering column.
  5. 5 Insert the new ignition cylinder into the steering column with the key in the "II" position on the cylinder.
  6. 6 Push the cylinder into the column until it "clicks," indicating that it is locked into the column.
  7. 7 Turn the ignition key to the "Off" position.

Dec 15, 2010 | 1995 Buick Riviera

1 Answer

How do you replace the ignition key switch for a '96 chevy diesel 1 ton 4wd pickup truck?


Ignition Switch Removal & Installation To Remove:
  1. Remove the steering column trim covers.
  2. Remove the wire harness from the retainers as needed.
  3. Slide the 2 connectors of the multifunction switch assembly out from the bulk head connector.
  4. Detach the key alarm connector from the lock assembly.
  5. Remove the ignition switch mounting screws and the ignition switch from the steering column.
Ignition switch removal/installation gm-08-00-1141.gif

To Install:
  1. Install the ignition switch on the lock module.
    • Tighten the screws to 42 lb in (4.7 Nm).
  2. Install the key alarm connector on the lock module.
  3. Slide the turn signal and multifunction switch connectors into the bulkhead connector.
  4. Install the harness in the original retainers.
  5. Install the steering column trim covers.
---
Ignition Lock Cylinder Removal & Installation To Remove:
  1. Disconnect the negative cable from the battery.
  2. Disable the supplemental inflatable restraint (SIR) system.
  3. Remove the steering column trim covers.
  4. Turn the ignition lock cylinder to the run position.
  5. Using an awl with a bent tip, insert the tip into the access hole of the ignition lock cylinder.
  6. Turn the lock cylinder to start and push down and hold the lock cylinder retaining pin.
  7. Release the lock cylinder to the run position and withdraw the cylinder from the steering column.
Ignition lock cylinder removal gm-08-00-1139.gif

To Install:
  1. Align the slot in the steering column to the tab on the lock cylinder and install the lock cylinder until it locks in place.
  2. Install the steering column trim covers
  3. Connect the negative cable to the battery
  4. Check for correct operation
prev.gif next.gif

Oct 08, 2010 | Chevrolet 3500 Cars & Trucks

2 Answers

Ignition


the actuator inside the sterring column that the lock cylinder turns is boken, this is a very complex job and is not for the home tech without a factory service manual.

Apr 21, 2010 | 1996 Ford Taurus

1 Answer

How do i remove key lock cylinder on steering column to replace with new one?


Turn ignition key/lock cylinder to the ON position. Insert a thin screwdriver into the slot adjacent to the switch attaching screw boss (right-hand slot). Depress the spring latch located at the bottom of the slot to release the key/lock cylinder. Remove the cylinder.
to remove key-lock cylinder switch Ignition Switch

Removal & Installation

1. Disconnect the negative battery cable.
2. Remove the steering column shroud and lower the steering column.
3. Detach the ignition switch electrical hardness connector.
4. Remove 2 nuts retaining the ignition switch to the steering column housing.
5. Lift the ignition switch upward to disengage the actuator rod from the switch and remove the switch.


To install:

> When installing the ignition switch, both the locking mechanism at the top of the column and the switch itself must be in the LOCK position for correct adjustment. To hold the mechanical parts of the column in the LOCK position, move the shift lever into PARK (with automatic transmissions) or REVERSE (with manual transmissions), turn the key to the LOCK position, and remove the key. New replacement switches, when received, are pinned in the LOCK position by a metal shipping pin inserted in a locking hole on the side of the switch.


6. Engage the actuator rod in the ignition switch.
7. Place the ignition switch on the steering column housing and loosely install 2 retaining nuts.
8. Move the switch up or down along the column to locate the mid-position of the actuator rod lash, then tighten the retaining nuts to 47-64 inch. Lbs. (5-7 Nm).
9. Raise the steering column into position at instrument panel. Install steering column shroud.
10. Connect the negative battery cable.
11. Remove the locking pin, connect the battery cable, and verified that the engine will only crank in PARK and NEUTRAL. Also check to make certain the start circuit cannot be actuated in the DRIVE and REVERSE positions.
to get more help on this issue with more details. then please click on this link directly
http://www.ehow.co.uk/how_5880956_change-ignition-lock-cylinder.html
thanks.this will help.

Feb 20, 2010 | Chevrolet Cavalier Cars & Trucks

1 Answer

2001 ford focus


If your Ford Focus is not starting, and you know the battery and alternator are good, the problem could lie in the ignition system. The ignition switch is a whole cylinder inserted into the steering column that connects to the starter motor. When you change an ignition switch, you are also replacing the key.

  1. Remove the dashboard panel below the steering column in your car; it should be screwed in place. Remove the steering column's upper cover by releasing its clips with a flat-head screwdriver.
  2. Look for the audio control switch---a small device sticking out of the steering column that acts like a remote control. If one exists, release the switch's plastic locking tang with the screwdriver, and unplug the electrical connector to remove the switch.
  3. Loosen the steering column by releasing the locking lever, and remove the steering column's lower cover by pulling out the screws with the screwdriver.
  4. Use your ignition key to turn the switch to the left---the position that would activate the accessories but not start the car. Insert the screwdriver into the hole in the top of the cylinder to depress the detent spring, and pull out the cylinder with the key inside.
  5. Insert the new key into the new ignition switch, and line up the switch inside the steering column so it's in the same place the old switch was in when you removed it. Make sure the detent locks into place; then turn the switch so it's in the "Off" position.
  6. Replace all the covers and panels you removed to access the cylinder, along with the audio control switch, if applicable, in reverse order of

Things You'll Need:
  • Small flat-head screwdriver
  • Ignition switch and key

Tips & Warnings
  • Older Ford Focus models may have a different method of removing and changing the ignition switch. Check an automotive guide for your particular year and model.
  • Always disconnect the negative (black) battery cable before working on the ignition or any other electrical component of your car.

I hope helped with this (remember rated this help) Good luck.

Nov 11, 2009 | Ford Cars & Trucks

1 Answer

I want to pull it


what year?

1999 electrcial ign switch. Lock cylinder is different

211-05: Steering Column Switches 1999 Town Car Workshop Manual
REMOVAL AND INSTALLATION Ignition Switch Removal
  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
  1. Position the LH instrument panel insulator aside.
    1. Remove the pin-type retainers.
    1. Position the insulator.
  1. Remove the LH instrument panel insulator.
    1. Disconnect the courtesy lamp.
    1. Remove the insulator.
  1. Remove the lower instrument panel steering column opening cover.
    • Remove the screws.
    • Unhook the parking brake release handle and position aside.
    • Remove the cover.
  1. Remove the five bolts to remove the instrument panel steering column opening cover reinforcement.
  1. Disconnect the ignition switch electrical connector.
    1. Loosen the bolt.
    1. Disconnect the electrical connector.
  1. NOTE: The ignition key should be in the OFF position.
    Remove the ignition switch.
    1. Remove the bolts.
    1. Remove the switch.
---------------------
SECTION 211-04: Steering Column 1999 Town Car Workshop Manual
REMOVAL AND INSTALLATION Ignition Switch Lock Cylinder —Functional Lock Cylinder Removal
  1. Disconnect the battery ground cable; for additional information, refer to Section 414-01 .
  1. Remove the ignition switch lock cylinder (11582).
    1. Insert the ignition key and turn to the RUN position.
    1. Press the ignition switch lock cylinder release pin while pulling out the ignition switch lock cylinder.

86b3f2f.gif

Apr 25, 2009 | Lincoln Town Car Cars & Trucks

2 Answers

96 ford windstar ignition probs


the ignition switch is the electrical part behind the lock cylinder where the key goes in.

Ignition Switch Lock Cylinder
Lock Cylinder Functional
Removal
  1. The following procedure applies to vehicles that have a functional ignition switch lock cylinder (11582) and keys. If the key numbers are known, the correct key can be made. Disconnect the battery ground cable (14301). For additional information, refer to Section 14-01 .
  1. Turn the ignition switch lock cylinder to the RUN position.
  1. Place a 3.17-mm (1/8-inch) diameter wire pin or small drift punch in the hole in the steering column shroud under the ignition switch lock cylinder. Depress the retaining pin while pulling out on the ignition switch lock cylinder to remove it from the housing of the steering column.
Installation
  1. Install the ignition switch lock cylinder by turning it to the RUN position and depressing the retaining pin. Insert the ignition switch lock cylinder into the steering column housing. Make sure the ignition switch lock cylinder is fully seated and aligned in the interlocking washer before turning the key to the OFF position. This will permit the retaining pin of the ignition switch lock cylinder to extend into the hole of the steering column.
  1. Using the key, rotate the ignition switch lock cylinder to make sure of correct mechanical operation in all positions.
  1. Connect the battery ground cable.
-------------------------------------------------------------------------------------
Ignition Switch Removal
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Remove the upper steering column shroud (3530) by removing the four or five self-tapping screws. Remove key release lever (3F527) (if equipped).
  1. Remove lower steering column shroud.
  1. Disconnect the ignition switch electrical connector.
  1. Rotate ignition switch lock cylinder (11582) to the RUN position.
  1. Remove the two screws retaining ignition switch (11572).
  1. Disengage the ignition switch from the actuator.


71f4c5f.gif


Item Part Number Description 1 11572 Ignition Switch 2 — Ignition Switch Lock Cylinder Housing 3 — Slot in Lock/Column Assembly A — (Part of 11572) Pin B — Alignment Mark
Installation
NOTE: A new replacement ignition switch assembly will be set in the RUN position as received.

  1. Adjust the ignition switch by sliding the carrier to the ignition switch RUN position.
  1. Check to make sure that the ignition switch lock cylinder is in the RUN position. The RUN position is achieved by rotating the ignition switch lock cylinder approximately 90 degrees from the LOCK position.
  1. Install the ignition switch into the actuator. It may be necessary to move the ignition switch slightly back and forth to align the ignition switch mounting holes with the lock cylinder housing threaded holes.
  1. Install retaining screws. Tighten to 5.6-7.9 Nm (50-69 lb-in).
  1. Connect electrical connector to ignition switch.
  1. Connect battery ground cable. Refer to Section 14-01 .
  1. Check ignition switch for proper function, including START and ACC positions. Also, make certain that the column is in the LOCK position.
  1. Install upper steering column shroud.
  1. Install the lower steering column shroud and key release lever (if equipped).

Feb 27, 2009 | 1996 Ford Windstar

Not finding what you are looking for?
2001 GMC Jimmy Logo

138 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...