Question about 1994 Ford Thunderbird

1 Answer

1994 ford thunderbird right side ball and socket how to repair or remove it

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

You have to remove the screw in the middle, get a ball joint seperator and pop it loose, then use a wrench and take it off.

You can go to autozone . com and register for free. Then login, choose your vehicle, then choose view repair manual for a free repair manual for your car. It will have step by step directions with pics

Posted on Jul 11, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to remove the old bearing from a 1994 ford thunderbird and replace it by hand. How do I do this and which direction do you go for removal.


bearing come out on the side they went in.
bearings r 2 pieces, the bearing and its race.
bearing is held in by some bolt arrangement so removing that allows bearing to come out.
race is press fit and requires a removing tool or access to the rear of bearing, a hammer and something to go between hammer and rear edge of bearing - then tap around edge to move it out.

Sep 21, 2014 | 1994 Ford Thunderbird

1 Answer

1997 ford thunderbird pulls right while driving at any speed, and pulls left while braking. The alignment is all good, pads are new, tires are new, ball joints and tie rods are tight, struts are good. any...


Possibly a right caliper not releasing, either a frozen caliper, or a bad rubber brake hose on the right front. After driving the vehicle, put your hand on or near the center of both front wheels and check for differences in temperature. If the right side is hotter, start checking caliper and hose.

Sep 04, 2011 | 1997 Ford Thunderbird LX

1 Answer

What order dose the sparke plugs go.



1994 Ford Thunderbird 3.8 liter SC V-6

zjlimited_93.gif


1994 Ford Thunderbird 3.8 liter V-6

zjlimited_94.gif


1994 Ford Thunderbird 4.6 liter SOHC V-8

zjlimited_95.gif


Hope helps.

Jan 02, 2011 | 1994 Ford Thunderbird

1 Answer

Can you show me detail pictures of step by step repair of ball joint and controll arm of 1990 ford thunderbird v6 3.1 automatc


prev.gif next.gif REMOVAL AND INSTALLATION Upper ball joints are not replaceable. The upper ball joint is part of the upper control arm bushing joint and is not serviced separately. If the upper ball joints are found to be defective, the entire upper control arm bushing joint assembly must be replaced. Lower Ball Joint INSPECTION
  1. Support the vehicle in normal driving position with ball joints loaded.
  2. Wipe the grease fitting and checking surface, so they are free of dirt and grease. The checking surface is the round boss into which the grease fitting is threaded.
  3. The checking surface should project outside the cover. If the checking surface is inside the cover, replace the lower arm assembly. prev.gif next.gif

Aug 26, 2010 | 1990 Ford Thunderbird

1 Answer

Where do i plug in obd2 reader for a 1994 ford thunderbird


Only 4.6L thunderbirds are OBD2 and it will be on the passenger side under the glove box. GOOD LUCK!

Sep 13, 2009 | 1994 Ford Thunderbird

1 Answer

How do change the rear right turn signal light bulb in a 94 ford thunderbird?


Typically you have to pull the (cardboard) liner in the trunk away from the light assembly, to get to the bulb. Then, gently twist the bulb holder one way or the other, until it comes loose from the tail light housing. Gently push the bulb in towards the socket that holds it, turn it counter-clockwise, and release the bulb. It should come loose. Assembly is the same, but in reverse.

Aug 14, 2009 | 1994 Ford Thunderbird

1 Answer

I need firing order for ford thunderbird 1994 4.6l v8.


My recollection is #1 is front passenger side, #5 is front dirver side.

Please rate if this is what you need.

May 09, 2009 | 1994 Ford Thunderbird

1 Answer

Tire off rack and pinion?


Not too clear what broke...Is it the ball joint or the c/v joint on the drive axle itself. If you are mechanically inclined neither job is impossible to do. However, It's not a job i'd do on the side of the road or in someone's parking lot. Unless it was a dire emergency, with no other options. From your post, I gather that you are not too familiar with auto repair, so maybe you should consider having it done by a reliable shop. If you do the job, I suggest you get a manual and ask qustions here if you have a problem.
Good luck

Mar 30, 2009 | 1993 Ford Thunderbird

1 Answer

Removing 1994 V8 Ford Thunderbird timing chain cover?


Have you removed the PS pump pulley? You need to do that to get it off.

Oct 06, 2008 | 1994 Ford Thunderbird

Not finding what you are looking for?
1994 Ford Thunderbird Logo

Related Topics:

176 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...