Question about 1990 Nissan 300ZX

Open Question

2003 nissan altima se 3.5 wont shift over 2500 rpm

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 36 Answers

SOURCE: 2003 Nissan altima alternator

You can go to your local Library, they usually have automotive manuals (Chiltons, Haynes, etc.) that you can check out. Or, you can purchase these at your local auto parts store $10-$20. They are very useful to have on hand and provide decent photos.

Posted on Aug 21, 2008

Ad
  • 2 Answers

SOURCE: 2003 nissan altima 2.5s transmission rough shift

Probably sensors! I have already replaced the crankshaft positioning sensor once, nissan replaced it once under recall and now it is bad again! Plus my speed sensor is bad too! Go to any part store and get diagnostic test ran, it will tell what sensors are bad.

Posted on Oct 02, 2008

SOURCE: 2003 Nissan Altima?

Where is the sensor placed on the car?

Posted on Oct 07, 2008

  • 4 Answers

SOURCE: 2003 nissan altima rpm goes

I have also read in the service manual that doing an idle relearn helps with RPM problems. This is the procedure below. It is complicated to do unless you have a watch or something to count the seconds with.

DESCRIPTION
“Accelerator Pedal Released Position Learning” is an operation to learn the fully released position of the accelerator
pedal by monitoring the accelerator pedal position sensor output signal. It must be performed each time
harness connector of accelerator pedal position sensor or ECM is disconnected.
OPERATION PROCEDURE
1. Make sure that accelerator pedal is fully released.
2. Turn ignition switch “ON” and wait at least 2 seconds.
3. Turn ignition switch “OFF” wait at least 10 seconds.
4. Turn ignition switch “ON” and wait at least 2 seconds.
5. Turn ignition switch “OFF” wait at least 10 seconds.
Throttle Valve Closed Position Learning UBS002OA
DESCRIPTION
“Throttle Valve Closed Position Learning” is an operation to learn the fully closed position of the throttle valve
by monitoring the throttle position sensor output signal. It must be performed each time harness connector of
electric throttle control actuator or ECM is disconnected.
OPERATION PROCEDURE
1. Make sure that accelerator pedal is fully released.
2. Turn ignition switch “ON”.
3. Turn ignition switch “OFF” wait at least 10 seconds.
Make sure that throttle valve moves during above 10 seconds by confirming the operating sound.
Idle Air Volume Learning UBS002OB
DESCRIPTION
“Idle Air Volume Learning” is an operation to learn the idle air volume that keeps each engine within the specific
range. It must be performed under any of the following conditions:
 Each time electric throttle control actuator or ECM is replaced.
 Idle speed or ignition timing is out of specification.
PREPARATION
Before performing “Idle Air Volume Learning”, make sure that all of the following conditions are satisfied.
Learning will be cancelled if any of the following conditions are missed for even a moment.
 Battery voltage: More than 12.9V (At idle)
 Engine coolant temperature: 70 - 95ーC (158 - 203ーF)
 PNP switch: ON
 Electric load switch: OFF
(Air conditioner, headlamp, rear window defogger)
On vehicles equipped with daytime light systems, set lighting switch to the 1st position to light
only small lamps.
 Steering wheel: Neutral (Straight-ahead position)
 Vehicle speed: Stopped

Posted on May 05, 2009

emissionwiz
  • 76070 Answers

SOURCE: Is there a way that I can reprogram a key fob

yes u can and here is the procedure.
1. Close and lock all doors with the driver’s side power lock/unlock switch.

2. Insert key into ignition and remove it from the ignition key cylinder at least six times within 10 seconds. Your Hazard
Lamps will flash if you have performed this step successfully. NOTE: Withdraw key completely from ignition cylinder
each time. If this procedure is performed too fast, system will not enter programming mode.

3. Insert key into the ignition cylinder and turn to the ACC position.

4. Within 5 seconds, push ANY button on the remote transmitter. Your Hazard Lamps should flash. NOTE: Do not press
the button more than one time in the above step. If the button is pressed more than one time, the programming
procedure will not be successful.


5. If there are any remaining transmitters (including the old ones), unlock then lock all doors using the driver’s side
power lock/unlock switch and within 5 seconds, push ANY button on the next remote. Your Hazard Lamps should
flash. Repeat this step for each transmitter (including any existing transmitters).

6. Turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door.

Posted on Jun 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 03 Nissan Altima wont get over 2500 rpms


first check your fuel system, replace fuel filter, also check your fuel pressure regulator on your fuel rail it may be leaking internally if ok check your fuel pump operation. if your fuel system is ok then check for a restricted catalytic converter its a common fault I encounter with them. if that to checks out ok then have the ecm scanned by a shop or the dealer could be a faulty engine speed sensor or crank or cam sensor

Jan 18, 2015 | 2003 Nissan Altima

1 Answer

MY 2003 NISSAN ALTIMA SE MAKES A CLINK NOISE WHEN ACCELERATING AT ABOUT 1700 RPM AND 2500 RPM OR GOING UPHILL ,NO NOISE WHEN REV UP OR IDLE OR TAKING OFF FAST


Wheel nuts loose, or stones in hub caps, do you get the noise rolling down hill ? , if not its engine, retrace your repair.

Nov 21, 2014 | 2003 Nissan Altima

1 Answer

While driving the car a 2003 2.5s will go from 2500 rpm to 4500 rpm and goes in and out of over drive its an automatic


Its a transmission problem check your transmission fluid and any possible vacuum hoses that go from the transmission to the engine.

Oct 06, 2013 | 2003 Nissan Altima

1 Answer

My 2003 Altima 2.5 will not shift into D. It will shift into R, 1, 2, and 3 just fine. Any ideas?


the shift lock control unit . stop working no ground out of the controler

Jan 12, 2011 | 2003 Nissan Altima

1 Answer

Relearn idle on 2003 nissan altima


Does the fuel gauge work properly? Recently had to have fuel sender unit replaced and Nissan dealership service to reset the idle learn on 03 Sentra SE-R Spec V. Engine idle rpm would go up and down as a result of bad sender.

Dec 18, 2010 | Nissan Altima Cars & Trucks

2 Answers

I need the Torque Specs for a Nissan Q-R 2.5 Engine?


Nissan QR 2.5 engine produces a torque of 180 ft·lbf (244 N·m) of torque at 4000 rpm .

Oct 11, 2009 | 2003 Nissan Sentra

2 Answers

The RPM of Nissan Altima stays high when drive over 65 MPH.


No....the rpms differ from engine to engine and from manufacturer to manufacturer. RPM's are always higher at higher speeds.

Aug 25, 2009 | 2002 Nissan Altima

1 Answer

My car doesnt pass 2500 rpm


I tell you how to fix it.
You drive 110.
You crash, and die.
My fault.
No, thanks.

Jul 07, 2017 | 2000 Nissan Altima

2 Answers

Stick shift # Automatic RPM


That is normal,If you do the same speed in 4th gear the rpm's will almost double.

The rpm's will repond faster in a manual than an automatic.

In a manual the engine supplies the power required directly to the gear that you have selected thus the engine rpm's will increase or decrease as needed.

Jan 07, 2009 | 2002 Nissan Altima

Not finding what you are looking for?
1990 Nissan 300ZX Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...