Question about 2002 Isuzu Rodeo

1 Answer

When changing tha water pump. D0 you have to set the timing?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 38 Answers

No and good luck!

Posted on Jul 11, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How d0 i change the clock time on my suzuki ignis vvt s auto1955


get in your owners manual if you don't have one contact your dealer they can order them for you

Jul 30, 2012 | 2005 Suzuki Ignis 1.5

2 Answers

I have a 2000 plymouth breeze an it keeps runing hot. But...the temp gauge isnt sayin anythinys wrong but i can hear an smell it running hot. My fans are working. The 1st guy said that it might be my...


Thanks for choosing FixYa and welcome to the site. They all are right. Anyone of those parts can cause overheating. The most common issue is the thermostat though, followed by the water pump. You could have a defective coolant sensor. If you have a bad head gasket, it will cause overheating. If you change the water pump, change the valve and the impeller also. Do this. Check your coolant level first and make sure it is level. You said fans are good. Make sure the radiator is good and is getting fluid inside it. Make sure there are no leaks. Check all coolant hoses. Like I said, the most common issue is a sticking thermostat or a bad one. Next, I would say the water pump.

Jun 07, 2011 | 2000 Plymouth Breeze

3 Answers

Do you have to change the water pump when changing the timing belt/timing?


You don't have too, but not bad idea, the timing belt drives the water pump, if you just replace timing belt, and not water pump, water pump could go out and mess up the timing belt, now it has to be done all over again, timing belt, water pump and labor.

Sep 16, 2010 | 1996 Subaru Legacy

1 Answer

Can someone help me? am traying to change tha wather pump but want some instructions like what to do first,where the pump is located, and so... thanks!!


5.2L and 5.9L Engines
See Figure 6
  1. Disconnect the negative battery cable.
  2. Open the radiator valve and drain the cooling system.
  3. Remove the cooling fan and shroud as an assembly.
  4. Remove the accessory drive belt.
  5. Remove the water pump pulley from the hub.
  6. Disconnect the hoses from the water pump.
  7. Loosen the heater hose coolant return tube mounting bolt and nut and remove the tube. Discard the O-ring.

3833dec.jpg

Fig. Fig. 6: Water pump mounting bolt locations
  1. Remove the water pump mounting bolts.
  2. Loosen the clamp at the water pump end of the bypass hose. Slip the bypass hose from the water pump while removing the pump from the engine. Discard the gasket.

To install:
  1. Clean all gasket mating surfaces.
  2. Guide the water pump and new gasket into position while connecting the bypass hose to the pump. Tighten the water pump bolts to 30 ft. lbs. (40 Nm).
  3. Install the bypass hose clamp.
  4. Spin the water pump to ensure the pump impeller does not rub against the timing chain cover.
  5. Coat a new O-ring with coolant and install it to the heater hose coolant return tube.
  6. Install the coolant return tube to the engine. Ensure the slot in the tube bracket is bottomed to the mounting bolt. This will properly position the return tube.
  7. Connect the radiator hose to the water pump.
  8. Connect the heater hose and clamp to the return tube.
  9. Install the water pump pulley and tighten the bolts to 20 ft. lbs. (27 Nm).
  10. Install the accessory drive belt.
  11. Install the cooling fan and shroud.
  12. Fill the cooling system.
  13. Connect the negative battery cable.
  14. Start the engine and check for leaks.


Hope helps.

Aug 19, 2010 | 1994 Jeep Grand Cherokee

2 Answers

How do you set the timing on a Plymouth Voyager ? I have to repace a broken timing belt. I was also told to replace the water pump is that true.


It is recommended because if you have to change the water pump belt change since you have to remove it and you save work in the future as we recommend changing the camshaft seals and crankshaft as it saves time and money

Feb 03, 2010 | 1992 Plymouth Voyager

1 Answer

Temprature light comes on after 4miles have changed thermastat but still light comes on fiat punto r reg 1997


There is not enough water in the system.
It seems so - enough water but ...... Filling up with whater you have to "pump" the hose from the engine to the radiator. This wicc secure tha air in the system will dissapear.

Jan 03, 2010 | 2006 Fiat 124

1 Answer

Honda accord


Unfortunately, u must remove the timing belt. This is why it is recommended to change the water pump when the timing belt is changed.
Here's the procedure : Disconnect neg. battery cable, remove splash shield at wheel well, (after removing wheel to help gain access, turn the engine to align timing marks and set #1 cylinder at top dead center on the COMPRESSION stroke. Once this is done, u can NOT disturb engine or u will have a fun time trying to figure out how the heck to set the timing. Drain anitfreeze, remove timing belt, remove water pump bolts (be aware that bolts may be different lengths, don't mix them up, remove water pump and O ring.
Put it back together: install new O ring and water pump, be careful Oring doesn't slip or move out of position, tighten to 9 ft lbs, install timing belt, refill antifreeze, reconnect battery cable, start car, check for leaks, bleed cooling system, replace splash shield.

Oct 19, 2008 | 1995 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14379 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...