Question about 1993 Chevrolet S-10

1 Answer

Door handle on left side 1993 chevy S10 need it now were does rod go in door to open

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

The rod you are talking about could be for the inside or outside handle which was not mentioned so I will give you both
You will see two tabs with black or rusty spring steel clips attached to the tabs. The one facing upward the most is for the outside door handle. The other is for the inside door handle
The rod will simply push onto the slotted clip to install. Now since the clips are very old and maybe rusty they can break upon installing the rod so new clips can be purchased at any GM dealer if needed

Posted on Jul 11, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My passagner door will not open either way inside


If you have the linkage there and it is working, Then the latch is broke. Replace it.

Oct 19, 2014 | 1993 Chevrolet S-10

1 Answer

I have a 1993 Chevy s10 extended cab Chevy an my


The lock is likely rusted and you will have to remove the inside door panel to get to it and spray it with PB Blaster and hope for the best. Work the outside handle and see if it opens up. Good luck.

Oct 13, 2014 | Cars & Trucks

1 Answer

2000 Chevy S10 passeger door won't open


Remove the door panel and inspect the latch rods for damage or broken retention clips. A video is below of how to remove the panel.

Nov 06, 2012 | 2000 Chevrolet S-10

3 Answers

Is there a piece that connects the door handle to the mechanism that opens the rear door on the 93 chevy suburban? our handle moves freely without opening the door


There is a rod that goes from handle to the latch. They are held in by plastic pieces that can come off. If you can somehow get the door open, you can remove the screws and pry off the door panel so you can get a better look

Apr 18, 2010 | 1993 Chevrolet Suburban

1 Answer

94 chevy lumina apv door will not open most of the time


since it is the drivers front door it could be the outside door handle , the rod that goes from the handle to the lock asbly or the lock asbly its self take the door trim panel off and then loos inside the door and latch the door with the door open. open the door with the outside door handle and watch the rod and the lever that the rod is pushing down the lever might not be pushing the lever down far enough to release the lock. If the lock does not open try pushing down on the lever and see if the lock releases if it does ck the outside door handle for cracks along the hinges of the handle I have found that most of the time that it is the outside door handle cracked and the rod is not moving the lever far enough to release the lock.

Feb 20, 2010 | 1994 Chevrolet Lumina APV

1 Answer

The left rear passenger door exterior door handle will not open the door. The interior door handle does work. how do I repair it?


You will need to remove the interior door panel and inspect the linkages. The offending rod should be obvious and loose.

Jan 17, 2010 | 1993 Ford Explorer Limited

4 Answers

I have a '93 Buick Regal Custom. Last year I was unable to open the passengers door from the outside, I can open from the inside but not outside. I lived with it until now. The drivers door is doing the...


I have this problem every year with my car, 1993 buick regal custom, 3.8. What happens is it gets cold, warms up a bit, and ice or snow melts and gets in the door, then it gets cold again and it freezes. I go to unlock and open the door from the outside and this problem arises.

There is a vertical rod on the left side of the drivers side, right side of the passenger side, that gets bent, from trying to open the door when that mechanism is frozen up. Just bend it back, a TINY bit and it will start working.

I got tired of taking my door apart every time it happened so i cut a little "door" in the cover thing, so i can get at that bar.

I also tried coating it in grease and that seems to lessen the frequency.

Jan 05, 2010 | 1993 Buick Regal

3 Answers

2003 chevy s10 blazer back hatch wont open


This is how to replace it on a 1996 Blazer 4dr.

First, go buy the part you need at Rockauto. The link is for a 1996, but make sure you order it for your vehicle. Just do a search for a Window Actuator Rod Retainer. Rock Auto requires you order a pair of these, so make sure you order two. Each one has two of them in there so you will have 3 extras.
Window Actuator Rod Retainers - RockAuto.com

To open the window in the mean time while you are waiting for the part, do the following.
1. Remove the two screws on the door handle so you can pull back the door panel.
2. Pull back panel on top in the middle where it rises.
3. Reach in with a screw driver or your fingers to push down the lever. It's a metal piece on the left side against the wall to the inside of the blazer.
4. Open window and tailgate and remove screws on the sides of the tailgate. There is one on each side. Make sure it is the one fartest out and on the plastic panel.
5. Once the screws are removed, pull up on half the panel that is farthest out from the truck. Slide out away from the truck. The panel should come off with a little effort. Do not pull up on the panel closest to the truck, you will break the hooks that hold it in. I broke two on mine. The panel will slide away from the truck pretty easily.
6. Remove the screws holding the middle metal panel down. There are about 12 screws. They are the 9/32 socket screws.
7. Pull the metal panel up, first dislodge the metal poles connected to the two white clips on each side in the center of the panel.
8. You will now see your actuator with the broken blue clip.
9. Pop off the blue retainer from the actuator. This will take some effort but it will pop off. (here's where you can replace the actuator if it's not making a sound)
10. Place one end of the retainer into the loose metal piece that rotates (left arrow in third picture) and then pop the other end back on to the actuator.
11. Replace the metal panel and clip the poles back into the white clips.
12. Make sure your door handle rod is clipped into the lock before you close the tailgate. If not, you have to work at opening it again by sliding you arm down between the plastic panel and it's not easy.
13. Replace everything. Before you close the door, make sure the door handle works and make sure the actuator is connected.
14. You should now be able to use your tailgate window again!

I am taking a guess your trying to remove the tailgate panel to fix this problem???

Dec 23, 2009 | 2003 Chevrolet Blazer

Not finding what you are looking for?
1993 Chevrolet S-10 Logo

Related Topics:

238 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...