Question about 2008 Dodge Caliber

1 Answer

Im in the process of wiring an air horn to my 2008 dodge caliber se. ive used the existing power feed and earthed the horn via an additional wire to an earth point. the horn works fine whilst the engine isnt running but once started the horn is poor and intermitent. any suggestions

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 46 Answers

Check your ground and clean it , also check your power source you may have 12v but not enough amps to make it work if you are using the standard horn power trying to run an airhorn motor may not be enough but most likely would be a ground problem

Posted on Jul 11, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Install air horns in 2001 Holden jackaroo using existing horn circuitry


There are a few ways of wiring a horn and I don't know how it is wired on your car so it is difficult to make any other suggestion than to wire it from the battery via a relay and a fuse. Use the original horn wiring to energise the relay.

Oct 09, 2017 | Holden Cars & Trucks

1 Answer

How can I disconnect the horn 2007 dodge caliber


Standard Caliber horn is drivers side behind bumper fascia - you could pull off the horn wire there.

Note that I wouldn't suggest driving around without a horn - safety issue.

Mar 13, 2015 | Dodge Cars & Trucks

1 Answer

How do i fix the horn on a 2007 dodge caliber?


not sure what exactly your after but if you push on the horn pad and you hear a click noise then the system is good from the pad to and through the horn relay. check for power at the horn wire itself. if this is good then replace the horn itself.

Sep 06, 2014 | 2007 Dodge Caliber 2.0

1 Answer

Problems with 2008 dodge caliber SE


Start with fuses, your owners manual will show you where to look.

Apr 17, 2013 | 2008 Dodge Caliber

1 Answer

Hyundai x2 Horn will not stop blowing


First check for faulty horn relay. If OK then check Horn pad, it is an earth switch and may be dammaged. Remove horn pad and check for wire off and contacting to earth or short to earth . If problem still exists with horn pad removed then the wire from horn relay to steering column is earthing out

Nov 24, 2012 | Cars & Trucks

1 Answer

1996 dodge neon horen fix


check horn relay.when you say replace did you replace horn control with airbag in steering wheel or did you replace horn.if you replace horn and fuse and relay okay problem is in the horn pad with airbag in steering wheel you have you replace it before horn will work again.

Nov 25, 2011 | 1996 Dodge Neon

2 Answers

How do i fix my 2008 dodge blower motor it is not blowing. when I'm driving i can feel cold air coming out of the vents but it does not actually blow.


most all items are controlled via CAN/OBD2 ECM's.Check Resistor also as this controls fan speeds.Not sure it Blower is now ECM controlled but Their are very few relays on these calibers and most everything is ECU controlled.This seems pretty stupid due to one ECM failure and whole vehicle is useless but It keeps dodge stealerships employed.Would have thought they used several for each system like GM so you can at least still use vehicle one of the many .... ABS/Airbag/Traction Control/Engine/Transmission system fails

Apr 21, 2011 | 2008 Dodge Caliber

1 Answer

I need to know the wiring diagram for 07 dodge caliber thanks


i doubt if you will get one ,these newer vehicles use encrypted software and modules so they do not use wires as such ,only 5 cables -two bus lines a perm 12v feed a earth and a 12v ignition switched feed .sorry--- again dealer only

Mar 08, 2010 | 2007 Dodge Caliber SXT Sport Hatchback

2 Answers

Horn is not woorking on 2008 chevy 2008


first test for power at the horn using a test light if no power then its not the horn check the fuse if fuse is good your problem can only be the clock spring which is located underneath the steering wheel,remove the wheel and its right there replace it and you will have horn power again.

Jan 29, 2010 | 2008 Chevrolet Hhr

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

178 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

80531 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...