Question about 2000 Nissan Maxima

Open Question

2001 nissan maxima keyless entry quit working

2001 nissan maxima keyless entry remotes and the interior power door lock wont work unless the car is running. they work fine yesterday. then last night they stopped working. I replaced the batteries in the remotes. If the car is running they work fine. you can until and lock the doors from the remote and doors. I checked all the fuses and they are fine.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

SOURCE: Keyless Remote, Power Antenna, and Clock problem

have u tried under the dash a black box which is to alarm open it up there will be 2 pins there that u need to bridge with a flat screwdriver at the same time the blinkers should flash then press each of your remotes to programme them hope this helps

Posted on May 24, 2008

Ad

SOURCE: nissan murano 2005 sl keyless entry remote programing

Close all vehicle doors, LOCK doors using drivers side switch.

Insert key all the way into the ignition, (do not turn) remove key.

Repeat this step 5 times. (6 total)

Hazards should flash to indicate program mode.

Press any button on transmitter to be programmed, hazards should flash to indicate successfull program.

*For additional remotes, cycle drivers door lock UNLOCK, LOCK, press any button on remote, hazards should flash. Repeat step as necessary.

Ignition ON, (engine off) ignition OFF, UNLOCK using drivers side switch, test remotes.

Source

Posted on Aug 06, 2008

SOURCE: 2005 Nissan Maxima, Power Locks Wont Work

All four door lock actuators were bad, fussed enough with dealer , they are fixing for free, save me $1600!

Posted on Nov 04, 2008

  • 59 Answers

SOURCE: nissan maxima 1997 sl - keyless remote problem

battery going bad

Posted on Dec 30, 2008

johnny5846
  • 379 Answers

SOURCE: location of a o2 sensor 2001 nissan maxima

bank 1 refers to the side of the engine that #1 cylinder is on , and sensor 2 refers to downstream , after the catalytic converter. , this link shows bank 1 on a 2001 nissan maxima V6 being on the firewall side . if you had a 4 cylinder it would be downstream after the catalytic converter .

http://www.autozone.com/N,26200242/shopping/specsSelect.htm



Posted on Jan 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2001 Chevrolet Impala Keyless Entry


Common problem, a small switch in the door lock breaks and does not activate the lock, all works from the key not remote, driver door recognises door not locked will unlock all doors, to repair you have to replace drivers door lock or just live with the key, I do
Merry Christmas

Dec 15, 2013 | 2001 Chevrolet Impala

1 Answer

Keyless entry wont unlock


TThere is probably a problem with the door unlock relay or the passenger door module. The passenger door modules on Jeep Cherokee have had a lot of problems and there are a couple of Technical Service bulletins published by the manufacturer as a result of these failures.

Jun 02, 2012 | 2001 Jeep Cherokee

1 Answer

2001 mustang keyless entry not working properly what do I do


You did it like this ?
Programming -Keyless Entry Remote Transmitter NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
NOTE: All previous transmitter identification codes (TIC's) will be erased when programming mode is entered.
NOTE: To program (or reprogram) the keyless entry remote transmitters into the generic electronic module (GEM)(14B204), perform the following steps.
  1. Turn the ignition from OFF to RUN eight times within 10 seconds, ending in RUN. If the GEM has successfully entered program mode, it will lock and unlock all the doors.
  1. NOTE: The first TIC must be entered within 7.5 seconds of entering the program mode and additional TICs must be entered within 7.5 seconds of the first TIC. The programming mode is exited whenever the timing constraints are not met. Press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait for several seconds and press the button again.
  1. Turn the ignition switch to the OFF position, or wait up to five minutes after step 1, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the GEM will lock and unlock all the doors one last time.

Jan 15, 2018 | 2001 Ford Mustang

1 Answer

Keyless remotes not working


Try reprogramming the remotes. Here are the instructions for the procedure. Hope it helps. Cobra!
Programming NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
NOTE: To program (or reprogram) the keyless entry remote transmitters into the RAP module, perform the following steps:
  1. Make sure that the anti-theft system is not armed or triggered.
  1. Turn the ignition switch (11572) from OFF to RUN eight times within ten seconds, ending in RUN. If the RAP module has successfully entered program mode, it will lock and then unlock all doors.
  1. Within 20 seconds, press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed. Repeat this step for each transmitter.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification.
  1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the RAP module will lock and unlock all doors one last time to confirm.

Jun 06, 2010 | 1998 Ford F150 Regular Cab

2 Answers

Keyless entry remote quit working. Just purchased new battery. Now Spare remote does not work either.


Transmitter Programming Notes Transmitter Programming

  1. Start with the ignition OFF, hold down the power unlock button on the door panel. Turn ignition key ON, OFF, ON, OFF. Release power unlock button on the door panel. The locks will cycle once.
  2. Hold down the keyless entry transmitter LOCK and UNLOCK buttons for 15 seconds . The locks will again cycle once.
  3. Repeat step #2 for each additional keyless entry transmitter.
  4. Turn the ignition on to exit the keyless entry transmitter programming mode. Programming is now complete

Jun 17, 2009 | 2000 GMC Sierra

1 Answer

Room Lamp fuse keeps blowing


i would first look in the main wire harness unbdere the dash on the drivers side it leads into the door also there is a harness that leads up the steering column to your dimmer/turnsignal module in the steering column. if your door locks stop working it colud be the master switch control in the drivers door this is whjere i would look for the short

Apr 19, 2009 | 2001 Nissan Maxima

2 Answers

Cannot get my car to lock without the keyless entry


check the room 10a fuse that is the problem

Feb 22, 2009 | 1997 Nissan Pathfinder

1 Answer

2005 Nissan Maxima, Power Locks Wont Work


All four door lock actuators were bad, fussed enough with dealer , they are fixing for free, save me $1600!

Oct 14, 2008 | 2005 Nissan Maxima

1 Answer

Cannot get car out of "Valet mode"


First start by looking inside the cars fuse box, there should be a fuse named "ROOM". Take it out and check if its still good. If not replace with the same amp fuse.

Aug 27, 2008 | 2001 Nissan Maxima

2 Answers

Door lock


Make sure the battery on your Keyless Entry remote is a working battery.

If thats not it, it could very well be the actual button on your Keyless Entry remote being faulty. But it could also be a relay in the car aswell. Depending on the cost of a Relay versus the cost of a Keyless Entry remote, I would try to replace either/or and try again, whichever is cheaper. The Relay may be cheaper, but your Key-FOB sounds like it could be the cause.

May 16, 2008 | 1994 Nissan Maxima

Not finding what you are looking for?
2000 Nissan Maxima Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

Marvin
Marvin

Level 3 Expert

83489 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22393 Answers

gerry bissi

Level 3 Expert

4387 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...