Question about 2002 Hummer H1

1 Answer

I need to know the head bolt tourqe for a 1980 tnt ski doo 1980 bombardier ski doo TNT

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,978 Answers

18 - 22 ft/lb

Posted on Aug 23, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I replaced the head bolts on a 300F ski-doo tundra what does the head get torqued at? I'm thinking not more than about 60/lbs


the specs say 21-22 ft/lbs. go google and type in ski-doo head torque specs
there is a page stratinglineproducts.com that shows the sequence for tensioning and the procedure
there are other pages and the tension is around the same figure.
At 60 I would say that you will strip the threads out of the block section.

Feb 08, 2015 | Cars & Trucks

1 Answer

What tools are neeeded to change brake pads for 2004 Jeep Liberty


1 or 2 sticks of TNT will loosen them bolts right up, then it's a piece of cake.

Sep 04, 2012 | Jeep Liberty Cars & Trucks

1 Answer

Need head bolts tourqe sequence for a 89 tercel


1989 L4 headbolt sequence:
Cylinder Head Bolt Torque Sequence809142031993 L4 headbolt sequence:
Cylinder Head Bolt Torque Sequence80914199they appear to be the same,other than the torque angle. good luck!

Oct 20, 2011 | 1993 Toyota Tercel

1 Answer

Im replacing the head gasket what is the tourq and sequence for instillation


A torque specification is how tight you must make the bolt by using a torque wrench which measures the tightness you apply to the bolt, ensure you are using new head bolts, a reliable torque wrench, clean the threads of the cylinder head (with tap) where head bolts screw into and when installing bolts ensure they are properly lubricated. And the sequence is the order in which you tighten each bolt.

Jun 19, 2010 | 1996 Acura TL Series

1 Answer

Head tourqe specs for 403 olds and bolt tightening


Fig. : Cylinder head torque sequence, 260, 307, 350 403 Oldsmobile built engines

5c04c01.jpg


On the V8, tighten the bolts, in the sequence illustrated, to 100 ft. lbs. When all bolts have been tightened to this figure, begin the tightening sequence again, and torque all bolts to 130 ft. lbs.

On V6's, tighten all head bolts in sequence to the following torques:
* All except bolts 5, 6, 11, 12, 13 and 14 - 100 ft. lbs.(19-135.5 Nm)
* Bolts 5, 6, 11, 12, 13, and 14 - 41 ft. lbs. (19-55.5 Nm)
* All bolts except 5, 6, 11, 12, 13, and 14 - 142 ft. lbs. (19-192.5 Nm)
* Bolts 5, 6, 11, 12, 13, and 14 - 59 ft. lbs. (19-80 Nm)

9fb545e.jpg

Hope this help (remember comment and rated this).

Mar 29, 2010 | 1984 Oldsmobile Cutlass

1 Answer

Need tourqe setting for head and intake bolts on 2000 land rover 4.0


Well, remembering that the head bolts are stretch bolts, which you tighten to 20nm (15lbf.ft) then turn 90 degrees, then a further 90 degrees :)
The inlet manifold you initially tighten them to 10Nm (7lbf.ft), then it says for the gasket clamp bolts you do those to 18Nm (13lbf.ft) and finally to 51Nm (38lbf.ft)

Feb 28, 2010 | 2000 Land Rover Discovery

2 Answers

Just replaced head gaskets and now it cranks over like no compression


how badly was this truck overheated? you may have collashed the rings and pistons, this would give near to zero compression

Oct 28, 2009 | 2000 Ford Ranger SuperCab

1 Answer

Toyota Vitz Engen Manual


If your head is leaking water you will need to replace the gasket and have the head checked out. Tightening the bolts will not do any good. Has the engine been hot. How do you know your water leak is in the head...

Oct 07, 2008 | 2007 Toyota Yaris

Not finding what you are looking for?
2002 Hummer H1 Logo

Related Topics:

220 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hummer Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Hummer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...