Question about 1993 Mercury Grand Marquis

2 Answers

How do you remove the fan on a 1993 grand marquis

Posted by Anonymous on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Expert
  • 312 Answers

Ford requires a special wrench to turn the nut to take off the fan.

Posted on Jul 11, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mercury Master
  • 6,826 Answers

Leave the belt on,and use a open end wrench(you may have to buy a special wrench to access the small space you have)and go counter clockwise,use a hammer,and hit the wrench hard to jar the nut loose.

Posted on Jul 11, 2010

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

MNfisherman
  • 11896 Answers

SOURCE: How to install a new power window motor in my 1993

Remove all screws to door panel. Remove the lock and window controls. Then take large flat-tip screwdriver and gently pry directly next to plastic studs holding panel on to door. Lift door panel off. Remove plastic out of the way. You will now have access to window motor. You may have to solder off old wiring. Or if you have enough to cut, would be good

Posted on Sep 11, 2009

  • 1986 Answers

SOURCE: how to remove the egr valve on a 1993 mercury

Jack up the passengers side of the car, get a 1 1/16" wrench break loose the fitting to the manifold, hold a 24 mm wrench on the fitting to the manifold, loosen the flare nut on the tube. Then using a 10 mm socket, about 2 inches long, loosen the two nuts under the EGR valve, then take the both out, remove the vacuum hose to the top of the EGR valve, and the sensing line from the small tube. then completely remove the flare nut from the orifice fitting on the manifold. BE CAREFUL with the tube, do not bend it or break it, you may find PB blaster useful the night before on a cold engine loosen these fittings. Once the EGR valve is out, remove the orifice out of the manifold, remove the tube from the EGR valve, again be careful, mark the tube to EGR position before pulling this off, because the top fitting to EGR needs tightened before you put it back in, it will make the lower fitting difficult if you do not line it up right, dry fitting from under the car is helpful, mark it, and then tighten the top. Clean out the tube, be careful not to bend the little tube, either inside or outside the larger tube, it sticks out inside. Clean the orifice, clean the manifold face carefully not to score it, check for blockage there too. Apply anti-seize to the orifice, put it back in the manifold, then apply anti-seize to the bolts for the EGR valve, and the flare nuts both ends. Apply some silicon to the EGR valve face, just enough to hold the gasket in place, put the new gasket on, start the bolts two turns in the gasket, it will hold them in place, then start them in the manifold, then start the lower flare fitting to orifice, tighten the top bolts, and then the flare nut, connect the vacuum line, connect the sensing line. I just recently did this process, it works, if have other EGR issues, the valve is the easiest.

Posted on Oct 13, 2009

  • 564 Answers

SOURCE: how to replace starter +1993 Mercury Grand Marquis

disconnect battery,,jack car up,,put jack stand on frame,,take starter bolts out,(may not be easy),,take wires off starter,,hoped it helped,,

Posted on May 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dashboard removabe 93 grand marquis


Long and laborious...About 40 screws and bolts.

Screws and bolts are found on the side of the dash, and under the dash. Keep removing them until you find the next binding point, and remove another fastener. Eventually you will remove them all...

Jan 26, 2014 | 1993 Mercury Grand Marquis

1 Answer

EGR valve replacement


REMOVE HOSE,REMOVE TWO BOLTS,REMOVE EGR VALVE.HERE'S A LINK. http://www.autozone.com/autozone/parts/Duralast-EGR-Valve/1993-Mercury-Grand-Marquis/_/N-izx7xZ93xpy?itemIdentifier=135996_0_0_

Nov 11, 2012 | 1993 Mercury Grand Marquis

1 Answer

How do i install the water pump for my 1993 mercury grand marquis


Fan clutch is attached to the water pump, willrequire a large crescent wrench or 36mm wrench. Take out the four plasticshroud bolts too that hold it on, 10mm I am thinking, that way you removeshroud and clutch as one. Carefully just sit clutch vertical...like it sits incar, so no silicone leaks out. Now you take the tension off the drive beltusing the 1/2" square hole in the tension pulley and drop the belt. Takeout the four bolts holding pulley to water pump, remove. Remove four boltsholding water pump and remove pump. Clean surface pump mounts to, make sure youuse a new o ring on new pump, should come with one, some do not. Reverse toinstall.

Jul 02, 2010 | 1993 Mercury Grand Marquis

2 Answers

How to replace starter +1993 Mercury Grand Marquis


disconnect battery,,jack car up,,put jack stand on frame,,take starter bolts out,(may not be easy),,take wires off starter,,hoped it helped,,

May 08, 2010 | 1993 Mercury Grand Marquis

1 Answer

How do i remove the fan on my 1993 grand marquis


there are 4 or so bolts on the front of the water pump belt pully that you will need to fully rfemove befor it will come off

Oct 10, 2009 | 1993 Mercury Grand Marquis

1 Answer

How to install a new power window motor in my 1993 Mercury Grand Marquis? I have a 1993 Mercury Grand Marquis Ls and the power window doesn't work. So then I bought some new window motors and I was...


Remove all screws to door panel. Remove the lock and window controls. Then take large flat-tip screwdriver and gently pry directly next to plastic studs holding panel on to door. Lift door panel off. Remove plastic out of the way. You will now have access to window motor. You may have to solder off old wiring. Or if you have enough to cut, would be good

Sep 11, 2009 | 1993 Mercury Grand Marquis

1 Answer

2000 grand marquis blower fan stops on lower speeds


there is a resistor for the fan motor which works the lower speeds, you need to replace that, it is normally located near the blower motor, got 3-6 wires plugged in it

Jun 28, 2009 | 1993 Mercury Grand Marquis

2 Answers

Blower fan stops on lower speeds 2000 grand marquis


There is a blower realy. Which steps the voltage up or down. If it fails it will run 12 volts or HIGH speed only... Replace that and your good.

Jun 28, 2009 | 1993 Mercury Grand Marquis

1 Answer

Engine


I put 1993 grand marquis engine fit into a 1992 grand marquis without too much trouble

Sep 23, 2008 | 1993 Mercury Grand Marquis

Not finding what you are looking for?
1993 Mercury Grand Marquis Logo

Related Topics:

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

fordexpert

Level 3 Expert

5471 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...