Question about 1993 Jeep Grand Cherokee

1 Answer

How do you get the ABS light to go off. There is

How do you get the ABS light to go off. There is no computer reset.

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 120 Answers

It wont go off unless you replace the bad part/s. Check your wheel sensors for broken wires and check and clean wheel sensor rotors.

Posted on Jul 11, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

How to reset abs light after installing new brakes

You should not have to unless you somehow messed up a abs sensor or connection. A scan tool would reset it and see which sensor is triggering the light. Also drive it for a day to make sure it doesn't go off by itself. Also check the back of the calipers where the connection is.

Jun 23, 2014 | 2006 Chevrolet Cobalt

1 Answer

Anti lock light flashing after changing battery

I can't think of a reason why the battery change should cause that light to flash. The ABS (Anti-lock Braking System) has a separate computer, probably under the hood someplace. Many of these have the word "reset" somewhere on the computer. Often if you hold a small magnet next to the word "reset" it may clear the computer and turn off the light.
There are ways to get the "fault codes" from the ABS by activating combinations of controls - like cruise control in combination with odometer, for example. The combinations are not logical. Search online for ABS and your car's make and model and you should find the instructions for getting and interpreting the codes. As an example three flashes of the ABS light followed by two more might mean right rear wheel sensor.

May 26, 2013 | 2001 Jeep Grand Cherokee

1 Answer

My ABS light on my Isuzu trooper remain on how can I reset

You first need to scan your Antilock Brake System (ABS) computer to retrieve the fault codes set by the system failure. The fault codes are needed to identify the correct diagnostic and service procedure to repair the broblem with your ABS system. It will do absolutely no good to reset the computer memory to turn the light out if the system failure is not properly diagnosed and repaired. This will only result in the light coming back on again.

Feb 17, 2012 | 2002 Isuzu Trooper

1 Answer

How do i reset abs light 1996 f250

On this 1996 ford the abs will reset itself as you drive about 1/4 mile, if the light stays on then theres still a problem. the computer will test the system at every key cycle and when theres a problem the light will come on and after the repairs are made and the computers runs a test and it passes then the light is turned off.good day, no scan tool needed will reset on its own.

Jun 19, 2011 | 1996 Ford F250 Crew Cab

2 Answers

How do i get the ABS lights to go off on 2002

you gotta have abs scaned find problem and repair then abs will reset, may have a bad wheel sensor.alot of things could make this light come on.

Sep 30, 2009 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

ABS light on fronm start up. Had problems witht he

just a guess on this but but have you tried resetting the computer for the switch?

Jun 27, 2009 | Jaguar XJ8 Cars & Trucks

1 Answer


just a thought but, disconnect the battery for 10 to 15 minutes to reset the memory. You might have a computer that is not resetting.

Also, even after resetting you might need to drive it to "force computer to recognize the faults are cleared.

Feb 14, 2009 | 2001 Honda Accord

1 Answer

2002 Chevy venture indicator trouble

Try disconnecting your battery for about 30 sec to reset the ABS computer. You probly have a trouble code stored in the ABS computer and the lights are letting you know there was a problem. If the light stays on after you reset computer then you will have to pull code to troubleshoot problem.

Joe. ASE Master Tech

Dec 14, 2008 | 2002 Chevrolet Venture Passanger

2 Answers



This could be a dirty or faulty wheel sensor, a faulty ABS pump, or a faulty ABS computer.

You could try cleaning the wheel sensors by spraying them with brake cleaner, and if this doesn't rectify the problem then a garage can read out the ABS fault codes and tell you what the problem is.

Sometimes just a reset is enough to clear it.



Jun 14, 2008 | 2002 Kia Sportage

Not finding what you are looking for?
1993 Jeep Grand Cherokee Logo

Related Topics:

185 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

83083 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides