Question about 2000 Ford Windstar

3 Answers

Fan/ventiation system has clicking noise; movingheating/cooling slider reduces or stops noise ; no or reduces warm air. 2000 windstar

Posted by on

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Automobile ventilation systems usually use a cable that connects a motor to a flap that blocks or permits air to pass to certain vents. There is also a flap which permits or blocks air from passing through the heating coil or a/c unit. A screw may have come loose cause the cable to slide without moving the vent flap, causing the flap and cable to be misaligned. Underneath or behind the dashboard is where all of this is located. Some vehicles it is easy to access and fix the cable/flap/screw problem, such a pickup trucks. Have a mechanic look at your ventilation system, as if the problem is a loose screw, it is a very easy fix, and shouldn't be too expensive with an honest mechanic.

Posted on Jul 15, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,669 Answers

Replace the temp control actuator.

Posted on Jul 11, 2010

Testimonial: "Prompt and helpful advice."

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

It's the blend door actuator, located behind the radio/climate control assy's.

Posted on Oct 30, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 NISSAN 4X4 P/U A/C SYSTEM WILL BLOW COLD WHEN OUTSIDE AIR TEMP IS COOL, WHEN HOT OUTSIDE AIR BLOWS HOT.


your auxillary fan is not working. this fan is responsible for cooling the freon that is being circulated in your cooling system... check if there are any loose wires in front of the engine bay.

the auxillary fan is located right beside your radiator fan.

May 17, 2012 | 2000 Nissan Frontier

1 Answer

Heater not blowing warm air


the windstar has a problem with heater control doors

Nov 30, 2011 | 2000 Ford Windstar

2 Answers

The ac starts out cold and stays that way on hwy driving but starts blowing warm air in stop and go traffic. why?


Either clutch coil is heating up and letting go Or one of the sensors is defective. Or there is a restriction somewhere in the line (open up hood and look for frost on a/c lines.)

Sep 21, 2010 | 2001 Ford Taurus

1 Answer

Heater not blowing heat just cold air also makes tapping noise


warm the engine a little and look for the 2 rubber heater hoses going into the firewall and feel to see if they aree both warm if not unhook them and using a garden hose push water through one way then the other and hook them up. Run with rad cap off untill warm to get any air out of the cooling system. If they are both warm look by the gas pedal there is a metal rod that sometimes gets kicked off that runs the blend door. (if you are hearing a flapping or ticking than mabey start with that).

Oct 24, 2009 | 2000 Ford Windstar

2 Answers

2000 Ford Windstar fan belt came off


the tensioner for the serpentine belt may be worn or seized. have the belt put back on and when this is done you will be able to tell how much tension is on it.

robert

Sep 14, 2009 | 2004 Ford Windstar

2 Answers

AC blows cold while moving, and gets warmer while I'm stopped


There are two fans behind the radiator. One is suppose to begin running when the AC is turned on. The other is to cool the radiator when it gets too warm. Raise the hood with the engine running and AC "on"and see if at least one fan is running.

May 04, 2009 | 1995 Buick LeSabre

1 Answer

Heater making noise and not blowing hot air.


You need to replace the temp actuator.

Apr 08, 2009 | 2001 Ford Windstar

1 Answer

95 Ford Windstar Vechile is running and warmed ,no heat


I had this problem recently too. Have the cooling system flushed and it will probably fix it. (heater core plugged)

Jan 27, 2009 | 2000 Ford Windstar

1 Answer

2000 ford windstar heater blowing cool air


Hi, You may have an air lock in the system. Have you ever had the system flushed out? This might be the fix. Also the thermostat might need to be replaced. You didn't say if you hear the clicking noise. If you do hear the clicking noise when you adjust the tempture control then its back to the replacement of the blender motor box with broken gears.
Hope this helps Warren

Nov 06, 2008 | 2000 Ford Windstar

Not finding what you are looking for?
2000 Ford Windstar Logo

554 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...