Question about 2000 Chevrolet 2500

Open Question

Location of crank sensor on 2000 chevy 2500 van

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 50 Answers

SOURCE: crank position sensor location

you will need to remove the starter to gain acess to the ckp sensor. once you remove the starter look on the engine block and you will see the sensor. The only problem with doing this repair yourself is that you will not be able to preform the crankshaft position variation learn procedure with out a factory scan tool. The vehicle may crank an run, but the timing advance curves will be wrong so the vehicle will probably cut off every time you remove your foot from the gas pedal. Hope this info helps!

Posted on Aug 18, 2008

Ad
emissionwiz
  • 76132 Answers

SOURCE: location of crank position sensor on 92 chevy corsica 3.1

You will have a no start or stalls after engine gets hot and then cools down restarts, the sensor is on the front of the engine mounted into the cam gear cover if it is not visiable get under the, (here is a picture) car and look.d37e0b9.jpg

Posted on Jan 21, 2009

tripletauto
  • 1450 Answers

SOURCE: Where is the location of the knock sensor for a 2005 HD 2500 6.0

HAS TWO KNOCK SENSORS they are both under intake in valley of engine. remove intake and will see two black grommets they are under those best to replace both at same time

Posted on Jan 26, 2009

billie17
  • 84 Answers

SOURCE: need to add 13-4a freon to my 2000 venture chevy van. Where is the pressure hose located?

passengers side under the hood.....by the firewall.....

Posted on May 12, 2009

Molson02536
  • 3854 Answers

SOURCE: location of the camshaft sensor on a 2000 chevy astro van

The sensor is in the distributor you can get it out with out pulling the distributor but its tight and has to be perfect .... pull the cap off and then the button youll see a sensor under a metal cup looking thing with a wire harness coming out of it i believe you need torks bits for the whole job if you go to any parts store and buy one then pull the cap this will make more sense.
Good luck and hope this helps.

Posted on May 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2009 Chevy 2500 cranks but won't start


gas? diesel? if its a 6.0 gas they have problems with the crank sensor. check for fuel pressure and spark. read the computer codes. probably crank sensor or fuel pump

Mar 16, 2013 | Cars & Trucks

1 Answer

How do you replace crankshaft sensors on a 2000 chevy venture


Why would you change a crank sensor

It failed a test?

How was it tested?

No parts get changed just for something to do

Dec 22, 2012 | 2000 Chevrolet Venture

1 Answer

2000 chevy 3/4 ton 2 wd 5.7L 42,ooo miles have no spark from ign. coil have replaced coil ,ign module and crank sensor please help


Better pull the dist. cap make sure the rotor turns when cranked,and if it does put a rotor on it.They will "fire" a hole thru the rotor to the shaft and kill the spark.

Jun 17, 2011 | 2000 Chevrolet 2500

1 Answer

2008 chevy express 2500 with a 6.0 crank sensor problems


check the alternator ouptut ,it shouldnt go above 15v ,

Aug 01, 2010 | 2008 Chevrolet Express

1 Answer

I have a 99 chevy 2500 van with a 350 in it. It


Start with the simple and check the fuse to the ECM. It may have blown and the crank shaft sensor wire harness which is located on the passenger side of the harmonic balance. The other thing also would be a problem with the passlock system if the van is equipped with one. Try turning the ignition key to the on position for 10 min then try starting the engine. Good luck and hope this helps.

Dec 23, 2009 | Chevrolet C2500 Cars & Trucks

2 Answers

How to test crank sensor 95 ram van 3.9


you will need a volt meter and know the voltage of the crank sensor so you will know if the voltage is good when you read it and try autozone.com for diagrams pictures and step by step instructions or your local library carries manuals for copies also

Mar 20, 2009 | 1995 Dodge Ram 2500

1 Answer

Where is the location of the knock sensor for a 2005 HD 2500 6.0


HAS TWO KNOCK SENSORS they are both under intake in valley of engine. remove intake and will see two black grommets they are under those best to replace both at same time

Jan 26, 2009 | 2000 Chevrolet 2500

Not finding what you are looking for?
2000 Chevrolet 2500 Logo

Related Topics:

268 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...