Question about Toyota Paseo

1 Answer

How do we change out the CVD axel on a 1996 Toyota Paseo. The car is already torn apart, we have the parts we just need step by step instrucitons and a diagram.

Posted by on

  • 1 more comment 
  • tdlksull Jul 10, 2010

    This was very helpful

  • tdlksull Jul 10, 2010

    Looks like the CVD broke inside, how do we pull that part out?

  • tdlksull Jul 11, 2010

    We were able to complete the job within a few hours thanks to your guidance. Thanks

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,926 Answers

  1. Raise and support the front of the vehicle, then remove the tire and wheel assembly.
  2. If equipped, remove the engine undercover.
  3. Remove the cotter pin and locknut cap.
  4. Depress the brake pedal to hold the hub stationary, then remove the bearing locknut from the hub.
  5. Remove the brake caliper and rotor.
  6. Remove the tie rod end from the steering knuckle, then place alignment marks on shock absorber lower bracket and camber adjust cam. Remove the bolt(s) and nut(s) securing the steering knuckle to the shock absorber, then disconnect the steering knuckle from the shock absorber, Figure 1.
  7. Pull the axle hub from driveshaft.
  8. If equipped, remove the stiffener plate (left side only) from the transaxle.
  9. Drain the fluid from the transaxle.
  10. Take a large screwdriver or pry bar between the CV joint and transaxle and remove pop the driveshaft from transaxle case.
  11. Make sure there is a new C-clip on the transaxle end of the new drive shaft.
  12. Reverse the procedure to install. When installing the new driveshaft, insert it into the transaxle as straight as possible and pop it back in. It will make a solid 'thunk' when it is inserted completely. Torque to specifications.

How do we change out - 6245cb0.gif

Posted on Jul 10, 2010

  • 1 more comment 
  • GetMeOttaHere Jul 10, 2010

    Torque the axle nut to approx. 65 ft lbs.

  • GetMeOttaHere Jul 11, 2010

    With a rubber mallet, hit the outside of the shaft untill the CV pops out. This is the best I can offer for removal at this time.

  • GetMeOttaHere Jul 11, 2010

    Excellent. Thanks for using Fixya.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i reset the computer on my 1996 toyota paseo after i changed the o2 sensor.


Computer are not reset

What your doing is clearing ALL
data within the pcm,ecm,ecu

That in no way fixes a thing

You now need a repair shop to start over
Road test checking fuel trim on a scan tool

Looking a cylinder misfire counts if avail

Looking at cylinder contribution
Ignition Spark lines & timing
Mechanical timing etc

Don't know what the problem is or was

Mar 01, 2013 | 1996 Toyota Paseo

1 Answer

My 1996 model EL54 Toyota Paseo is idling at about 1500rpm, the adjuster is at its lowest setting a i've been told that the throttle sensor may need either cleaning or replacing but I'm not...


Not the throttle sensor (tps) remove the Idle air control (iac), High RPM's are caused from vaccumn leaks, you have a computor, put Autozone in the search, enter info on the car and search for the part, you will now know what it looks like, IAC and TPS are located at the throttle body, remove and clean with throttle body cleaner purchased at your local auto parts store

Jul 30, 2011 | 1993 Toyota Paseo

1 Answer

Starter 96 toyota paseo


You want a new one. It will cost you about sixty if your lucky. Hard to get it in and out of the small engine but you can do it. Its like three or four bolts and two wires. It attched to the transmission

Mar 02, 2010 | 1996 Toyota Paseo

1 Answer

1996 Toyota Paseo check engine light on


The Paseo is OBD2 (all '96 and up are, a few 95's of certain manufacturers are also, but generally anything 95 and older is OBD1). There are 2 possible locations, the one under the hood that you found, and another in the more typical driver side of steering column, below dash.

Sep 28, 2009 | 1996 Toyota Paseo

1 Answer

94 toyota paseo need to replace valve stem seals


YES if you don't have the right tools
or the know how.
may want to take this one to a good shop.

Sep 09, 2009 | 1996 Toyota Paseo

1 Answer

Synthetic or stay with regular oil ?


I would not change to synthetic. The Paseo engine is not designed for it, and the benefit of synthetic oil will not be realized. Save your money, and stay with the regular oil.

May 19, 2009 | 1996 Toyota Paseo

1 Answer

Location of starter 1996 toyota paseo


under the bottom of car on the engine block next to trans and engine meet

Jan 03, 2009 | 1996 Toyota Paseo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...