Question about 2003 Nissan Sentra

1 Answer

A/c blowing very weak,fan is runnuing at all speeds;just isn't putting out at vents

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 32 Answers

You should change the air filter. behind the glove box is the location of the a/c air filter.
1. remove glove box
2. remove filter cover
then replace with new one.
hope this would help...

Posted on Jul 10, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 Pontiac Montana heat gets hot in front, blows but seems weak, and no heat on rear controls but blows ******* rear. what is going on?


Is your heater blower motor working on all speeds ? Are you get any air coming from the rear vents ?

Feb 25, 2015 | 2003 Pontiac Montana

1 Answer

In cold temp,heater motor do not run


you mean low heat. at all ducts with full fan speed and blows hard,
here is the correct order.
1: engine at 180F or more holding, a absolute must.
2: fan runs at full speed on HIGH, (sounds like it)
3: fan actual blows (felt) at full speed, to any vent, try all vents.
4: now heat, will happen, if not, the dampers are closed or wrong.
damper can be complex on newer cars,they have motor controlled damper servos';

is this just blower fan dead? problem. on high, if yes say so.

Jan 26, 2014 | 2008 Suzuki Grand Vitara

1 Answer

My bmw318i heating stop blowing out ,what can i do


If the fan isn't working then it is probably the fan speed resistor which is faulty.

Nov 29, 2011 | 1996 BMW 318

2 Answers

On my 1998 olds 88 I don't seem to have a good volume of air coming from the vents. The fans blow the a/c is cold but just not good air flow. How can increase the air flow?


Hello and welcome to FIxYa!
You may want to check on the vents for it can be closed half way. If the vents are good then the problem will surely be on the blower itself. It can be worn out that's why the blower motor blows weak. Once replaced I believe you'll be good.
Hope this helps and thank you for using FixYa! Have a good one!

Aug 09, 2011 | Oldsmobile 88 Cars & Trucks

1 Answer

Air flow threw vents & floor are weak on 1989 chevy s10 pickup


Thinking the screen in front of the AC evaporator is plugged. Should be able to take out the fan speed resistor (from under the hood) and gain some axcess to the front of the evap.I usually spray it with brake cleaner or elec. contact cleaner and blow with compressed air,gets most of it out.

Dec 11, 2010 | 1997 Chevrolet S-10 Pickup

1 Answer

Why is the blower not blow strong air out i put new moter in but it still does not blow good


do all of the fan speeds work? if not you need to replace the blower motor resister. If all of the fan speeds work then you need to clean or replace your in cabin air filter. When this filter gets clogged you get very little air flow from your vents. Instructions for your cabin air filter service are in your owner's manual

Sep 19, 2010 | 1999 Lincoln Town Car

1 Answer

I have a 1991 Buick Park avenue with 44,000 miles that is not blowing air through the vents. I just put a brand new resistor in and that changed nothing. The fan spins at a low speed when the car is turned...


Switch the relay with one of the other relays to make sure that this relay is good then go to the HVAC control programer which is behind the floor vent (middle). The Blk/gray wire is the one that supports the relay coming out of the HVAC programmer, but there is a chance that this programmer is bad. If that proves to be the case, I may even have one...let me know.

Aug 06, 2010 | 1991 Buick Park Avenue

1 Answer

98 Olds LLC - AC works but fan air does not blow


If you have a late model GM car and the system is controlled electronically the blend door actuator becomes weak. When this situation occurs it will not move the air direction door inside of the heater/air conditioner plenum. in your case not to the vents Replace the actuator with new and recheck the system. i hope this helps

Jul 24, 2009 | 1995 Oldsmobile Cutlass Ciera

1 Answer

Just had my heater core replaced and do not see much difference.


the unit were you turn on the fan leaks vacuum which causes the vents not to blow properly the unit is not expensive for it is plastic comes with fan switch ex..

Feb 24, 2009 | 1995 Chevrolet Blazer

1 Answer

Heater on driver-side blows barely warm air other vents blow cold


the most probabale cause of this would be a disfunctional hear core if you replace your heater your heater will more than likley work the the way it's supposed to

Jan 18, 2009 | 2001 Dodge Grand Caravan

Not finding what you are looking for?
2003 Nissan Sentra Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...