Question about 2002 Jeep Wrangler

1 Answer

Air wont switch from defrost to vent

I just replaced the relay and the resistor,fixed the problem of fan control but not direction control

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 6,826 Answers

The vacuum tubes behind the panel might have broken or become disconnected. This system operates the door that controls defrost to vent routing of air in the car's ventilation system.

Hope this helps.

Posted on Jul 10, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have replaced the blower relay, the resistor looks fine, but blower won't work on my 1986 Silverado


Change the resistor. For the 15-20 bucks it's a great diagnostic and a very common problem with GM vehicles.
Then you can start backtracing the harness as ray012965 suggested.

Dec 16, 2014 | Cars & Trucks

1 Answer

Climate control fan not working


You will need to replace the fan blower motor switch resistor as well as the blower motor resistor harness.

The resistor can be located under the glove box (directly above where you passengers right foot wood be pointing if sitting in truck.

This is a common problem much has been written about it. You can find a detealied fix on youtube.,

Oct 17, 2013 | 2008 Hummer H3

1 Answer

Fan motor blower not working


According to the wiring diagram, there are only three components to the system. The blower motor, the resistor, and the speed control switch.
The resistor gets power from the switch which is powered by a 25amp fuse. On high setting the resistor is bypassed and the blower motor gets power from a 30amp circuit breaker. The blower is grounded to the body. The fuse is hot in the "run" position and the 30amp breaker is hot all the time.
So you should have power at the blower motor on one of the settings and a direct ground on the black wire.

Aug 13, 2012 | 2000 Chevrolet Venture

1 Answer

Fan speed only works on high which should have the least resitance. I can't find the relay that should be on the pass. side under dash. can someone direct me?


You likely need to replace the Resistor which controls the voltge delivered to the fan motor.
Your symptom shows this is right.

The resistor is inside the air box directly in the flow of air from the fan. You MUST have it fully installed before powering on the fan or it will burn out immediatly. Needs the air flow to keep cool.
You may need to pop out the glove box, then you should see a few wires going into the air assembly under the passenger side, being held in with 2 screws. Yours maybe slightly different. Ignition off, remove the couple screws and extract the plastic block holding the resistor lump. About 12 - 20 $ at auto parts store to replace. Pu the new one in and screwed down BEFORE turning on ignition.
Good luck

Mar 07, 2011 | Dodge Dakota Cars & Trucks

3 Answers

99 explorer fan only works on high


You need a blower motor resistor pack, follow the wire from the motor it will go into a connector with a few wires at the resistor pack. it's held in by 2 screws- easy to change.

Jan 22, 2011 | 1999 Ford Explorer

1 Answer

My hearter fans will not turn off. when i turn my truck off.


Relay for the heater fan is the most likely problem, replace the relay and if that does not fix the issue the problem could also be in the resistor pack for the fan control.

Jan 23, 2010 | 2003 GMC Yukon Denali

1 Answer

My heater fan is not working on my jaguar x tyoe fuse ok what could it be


Check the fan motor runs ok if power directly applied to it,
if OK:-
check operation/replace blower motor control relay (if fitted),
check fan speed control resistor pack- usually mounted in heater air ducting.

Nov 11, 2009 | 2002 Jaguar X-Type

1 Answer

MY HVAC fan stopped blowing. Checked all the


Check the blower motor speed control resistor pack is ok.
(The resistor pack is usually located in the blower fan ducting in the air flow).
Check condition of electrical connection terminals on the blower motor circuit - these terminals pass considerable current and over time may fatigue overheat and loosen.
Check operation/replace any blower motor control relay,
Check the blower motor will run if +12v directly applied to the blower motor.
Check operation of the blower motor speed control switch is ok.

Oct 08, 2009 | 2003 GMC Sierra

3 Answers

The heater blower/a/c switch on my Mazda MX5 only works on full speed. How can I fix it? Is there a relay to replace or something? Help!! Tony


you need to replace the blower resistor located on the blower housing between the blower and the evaporator behind the glove box...this should fix you rite up.......

Sep 20, 2009 | 1991 Mazda MX-5

Not finding what you are looking for?
2002 Jeep Wrangler Logo

188 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

81294 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...