Question about Ford Laser

1 Answer

FORD LASER 1999: Car stays in intermediate gear, (2nd?) And hold light flashes on (maybe when the brakes put on, im not too sure)

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

Inside the transmissions lower trans pan upin removal you will see electronic solenoids mounted in there. The 3rd gear solenoid is at fault which neds to be replaced. That will get the trans to shift correctly again. Change the filter and fluid at the sam time as well
The solenoid needs to be purchased at a ford parts department as well

Posted on Jul 10, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will not shift


4 post is the shifter stuck in park?
if so, that is a features, called Park lock out.
that means you can not put car in gear, Drive, Rev., 1 or 2nd.
check fuses first.
then make sure brake lights at rear of car actually work.
then post.

Mar 14, 2015 | 1999 Suzuki Grand Vitara

2 Answers

1992 Ford F250 with 7.5 l has only 2nd gear and the overdrive light is flashing


Make sure the filter is clean and you have the correct fluid in it. Also check that the shift cable adjustment is correct.

May 04, 2014 | 1992 Ford F250

1 Answer

Will not shift out of 2nd gear


Tranny most likely shot. I believe yours is a T-5, I had the same issue years back but in 3rd gear. Usually the clutch going out is a gradual thing. So I would have a tranny shop look at it. Maybe find a cheap rebuilt tranny for ya.Look online or a trusted shop.

Mar 23, 2014 | 1994 Ford Mustang

1 Answer

I have a 1999 ford au automatic and it keeps on slipping out of gear i've had 2 different answers 1st is the solenoids are gone the 2nd is to check transmission fluid. im aware there's no dip stick for the...


Taurus? It has a dipstick. It is near the brake booster. It is yellow. Is this a problem with it coming out of gear at stop signs? Does it just start working again or do you have to shut it off and let it sit before it starts moving again?

Nov 19, 2010 | 1999 Ford Taurus

1 Answer

Im not getting any power to the brake light switch 1999 GT mustan


Check fuse #41, if its good then the brake switch may need replacing. You can test the power to the switch by the use of a voltage meter touching the LG/RD (light green/red) wire with the red side of the meter and the other probe to ground. If more than 10 volts its good. You can check the BPP (brake pedal position switch) by installing a fused jumper wire from LG/RD to the RD/LG wires. Connect a 10A fused jumper wire between C242, Circuit 10 (LG/RD), harness side and C242, Circuit 810 (RD/LG), harness side. And check the brake lights, if they go on then the switch is defective. Hope this helps you.

Mar 24, 2010 | 1999 Ford Mustang Cobra

1 Answer

I have a 2000 Expedition 4.6L Triton. I've had truck about 7 years and love it. I have had all the transmission issues this truck can have...(I thought) until now this: SYMPTOM Transmission drives well in...


4R100 or 4R70W?

Geartrain
Power is transmitted from the torque converter to the geartrain components through the input shaft and forward clutch cylinder.
  • By holding or driving certain members of the gearset, four forward ratios and one reverse ratio are obtained and transmitted to the output shaft. The ratios are as follows:


GEAR RATIO 1ST 2.71 to 1 2ND 1.54 to 1 3RD 1.00 to 1 4TH 0.71 to 1 REVERSE 2.18 to 1
Input Shaft
The input shaft is supported by two bushings in the stator support. End positioning of the input shaft is controlled by the splines in the converter turbine and the overdrive planet assembly.
Output Shaft
The output shaft is supported by two bushings in the case and by the slip-yoke and bushing in the extension housing. End positioning is controlled by the parking pawl gear and snap ring or shoulder and by the reverse ring gear hub and snap ring.
Overdrive System
The overdrive planetary system consists of the overdrive planet assembly, overdrive sun gear, overdrive ring gear, coast clutch cylinder, overdrive one-way clutch assembly and the center shaft, as shown in the following illustration. The overdrive planet assembly is splined to the input shaft. The overdrive sun gear is centered by a bushing on the input shaft and held in place laterally by needle bearings on the reactor support and the overdrive planet assembly. The overdrive sun gear is splined to the coast clutch cylinder, which in turn is splined to the overdrive one-way clutch inner race.
The outer race of the one-way clutch is splined to the overdrive ring gear, which is splined to the center shaft. The center shaft is centered by the forward planetary assembly and is laterally held by needle bearings on the center support and the overdrive planet assembly. The center shaft is splined into the forward clutch cylinder.
Two friction clutches are assembled in the overdrive planet assembly. The coast clutch is splined between the coast clutch cylinder and the overdrive ring gear. The coast clutch is activated to perform engine braking in MANUAL 1, MANUAL 2 and third gear with the transmission control switch engaged.
The overdrive clutch is splined between the case and the coast clutch cylinder. The overdrive clutch holds the coast clutch cylinder and, in turn, the overdrive sun gear, to permit the planet assembly to overdrive the ring gear.
--------------------------------------------------------------------------------------------
Forward Drive System
The forward drive system consists of the forward clutch cylinder, intermediate brake drum, intermediate one-way clutch, input shell, forward ring gear, forward ring gear hub, forward/reverse sun gear and the forward planetary carrier and forward planetary gears.
The forward clutch cylinder is splined on the center shaft. The forward ring gear is piloted on the forward ring gear hub. Thrust bearings on the forward planet assembly and forward clutch cylinder hold the forward ring gear hub in place.
The intermediate brake drum is radially supported by bushings on the center support and is laterally controlled by thrust washers on the forward clutch cylinder and center support. The intermediate brake drum has the inner race of the intermediate one-way clutch press-fitted on its pilot. The intermediate one-way clutch's outer race is splined to the intermediate friction clutch, which is splined to the case. The intermediate brake drum has lugs that are slotted into the input shell to form a mechanical connection. The input shell is splined into the forward/reverse sun gear. The forward/reverse sun gear is common to two planetary gearsets. The forward planet is splined to the output shaft and is laterally positioned by needle bearings on the sun gear and on the forward clutch cylinder, as shown in the following illustration.
Two friction clutch assemblies, the direct clutch and the forward clutch, are shown with the forward planetary assembly. The direct clutch assembly splines the forward clutch cylinder to the intermediate brake drum. The forward clutch assembly splines the forward clutch cylinder to the forward ring gear. The forward clutch is activated during all forward gears. While in third or fourth gear, both the direct and forward clutches are applied to hold the forward planetary assembly and enable it to act as a solid shaft.
In second gear, the intermediate clutch assembly holds the forward/reverse sun gears. It is applied, along with the intermediate one-way clutch, to hold the intermediate brake drum, input shell and forward/reverse sun gear. In higher gears, the one-way clutch overruns.
----------------------------------
Low and Reverse Drive System
The reverse planetary assembly consists of the reverse planetary carrier, reverse planet gears, the reverse ring gear, the reverse ring gear hub, the reverse clutch hub and the low-reverse one-way clutch assembly.
The reverse ring gear hub is splined to the output shaft and to the reverse ring gear. The reverse ring gear hub is laterally held by a needle bearing on the inner race of the low-reverse one-way clutch and a snap ring on the output shaft. The reverse planet assembly is splined to the low-reverse clutch hub. The low-reverse clutch hub is connected by the reverse clutch to the case. The inner race of the one-way clutch is bolted to the case.
The reverse clutch assembly is activated in REVERSE gear and in MANUAL 1. The reverse clutch bypasses the reverse one-way clutch during coast and MANUAL 1. The reverse clutch holds the reverse planet assembly in REVERSE gear to enable the sun gear to drive the reverse ring gear in the opposite direction.
-------------
Apply Components
The following information describes the operation of the three 4R100 one-way clutches.
One-Way Clutch—Overdrive
The overdrive one-way clutch, shown in the following illustration, transmits engine torque from the overdrive sun gear to the overdrive ring gear in first, second and third gear range. The overdrive one-way clutch transmits power when the sprags are engaged between the inner and outer races. The inner race is splined to the coast clutch cylinder, which in turn is splined to the overdrive sun gear. The outer race is splined to the overdrive ring gear.
The overdrive one-way clutch engages whenever the overdrive planetary system attempts to drive the overdrive sun gear clockwise when the overdrive ring gear has a counterclockwise torque from the vehicle. When torqued counterclockwise, the overdrive one-way clutch engages and acts as a wedge to lock the sun gear and the ring gear together. During coast, the overdrive one-way clutch enables the ring gear to overrun or spin at a faster rate than the sun gear.
The overdrive one-way clutch overruns when in overdrive (fourth gear). In overdrive, the coast clutch cylinder is held by the overdrive one-way clutch, which in turn holds the overdrive sun gear. This causes the overdrive planet assembly to walk around the sun gear and overdrive the overdrive ring gear. The inner race of the overdrive one-way clutch is thus held stationary while the outer race is allowed to overrun clockwise.
--------------------------------------------

Nov 10, 2009 | 2000 Ford Expedition

1 Answer

My 96 ford probe is stuck on overdrive everytime i put it inot drive or 1st or 2nd gear if im at a stop it wont start to move until 2000rpm and idk all that it does when i hit the button is stay on and the...


You have overdrive cancel soleniod problem. What it does, when you hit the overdrive buttom it activate the overdrive off and on. You should have it check.

Aug 04, 2009 | 1996 Ford Probe

1 Answer

1999 ford expedition,my rpms revs up in between 1st and 2nd gear


Rebuilding one of these right now! The 4R100 trans has a rachet type of intermediate sprag that fails. They break apart, bind up and eventually second gear is gone.
Otherwise it may be just a simple valve body calibration kit could cure. This is common also. And cheaper! Excessive metal in the pan would be a sign of the bigger problem listed above

Apr 02, 2009 | 1999 Ford Expedition

2 Answers

Ford focus 04, handbrake light stays on when driving but faded


make sure u are not low on brake fluid,this will also illuminate the red brake light.

Feb 11, 2009 | 2002 Ford SVT Focus

3 Answers

Tranmission problem on 1999 Dodge Grand Caravan


When the trans. sticks itself in 2nd gear and stays there is because it's detecting a trans. problem and puts itself in "limp in" mode. When it happens again, to somewhere to have a scan done on the trans. so you can find out which sensor on the trans. is acting up.

Jun 22, 2008 | 1999 Dodge Grand Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

331 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...