Question about 2003 Kia Sedona

1 Answer

I turned the engine over with one injector out and heard a bang and now i think im missing a part what should be under the injector?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Kia Master
  • 2,019 Answers

There is probably a rubber seal on the end of the injector. A new one is probably on a half dollar. You should have removed the engine position sensor plug first, so there would be no ignition.

Posted on Jul 10, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2001ford ranger engine light flashing, vehicle lightly shakes when idle, decrease in acceleration, gas cap seal tightly, no leaks, no indicating sounds-such clanks, tings, bangs

A blinking service engine light indicates an engine miss. Take your car into any/most parts house and they will use a code reader/scanner to see which code number is being set and then identify your engine cylinder that is not functioning properly. Once you identify the cylinder you can start to check different systems, spark plug, wires, injectors,ect. to find your problem and fix the miss.

Jun 03, 2017 | Cars & Trucks

1 Answer

1988 Toyota Camry 2.5 liter V-6. Engine starts fine, but after started it misses. The car misses terribly under a load, but will sometimes accelerate smoothly if you accelerate at a very slow pace. Will...

most misses are injector related either from dirty injectors , low fuel pressure ow injector wiring faults
use a quality injector cleaner for a tank or two
run the fault codes to check for other related sensor problems

May 23, 2017 | 1988 Toyota Camry

1 Answer

Wiring diagram for the ecm plugs

Im idling at the light in my 2000 Dakota R/T and all of a sudden my check engine light comes on and the engine develops a miss and starts to smoke. Diag code says misfire in #5 cyl and there is a rich raw fuel smell from exhaust. I have 175K trouble free miles and have checked compression which reveals worn but good piston rings.I replaced head gaskets and of course still exists. When I got a hand to crank while I checked voltage at each injector, #5 showed higher than the rest at all times without dropping to zero, so i'm replacing the ECM which controls signals to injectors. Oh yeah I replaced #5 injector before voltage check to no avail. Tell me if you think Im on the right track replacing ECM.

Oct 02, 2010 | Dodge Grand Caravan Cars & Trucks

1 Answer

Miss in engine. DB2 codes indicated miss in

you may have a stuck injector (if your engine has an injector for each cylinder) ... if you place a stethoscope (or just a stick) on each injector you can hear them click as the engine runs .. if the one on cylinder 2 is stuck then it will stop clicking .. you can use some injector cleaner in your gas but the injector has to start working a little before it can do much good .. so if it works sometimes and not others then that might be worth a try .. if you cant get it working (wont click) then often you can pulse it into operation by very briefly touching 12volt across its coil .. if you keep the 12 volts on for too long it will damage the injector coil .. if you have only one injector then thats not your trouble ..
the cleaner usualy does the trick if you can get it to operate even for a short time .. you can also replace the injector if you determine that its bad ..

Feb 27, 2010 | Pontiac Sunfire Cars & Trucks

1 Answer

94 Accord Banging/knocking when i turn

check the axles for leaking boots or dry axle joints....replace if necessary...also make sure all brake caliper bolts are all installed and correctly torqued

Apr 07, 2009 | 1994 Honda Accord

2 Answers

2001 ford taurus p0301 and p0303

You are mis fireing on cyl 1 and 3 if you replaced plugs and wires and coil this is going to be a fuel injector issue or valve issue. See if you can swap the injectors with known good cyl. and see if it changes. Or have a shop do a fuel injector service on it to see if it helps. It may be to late for the fuel injector service.

Mar 01, 2009 | 2001 Ford Taurus

1 Answer

Engine idle? fuel filter or injectors?

Dont bother with the filter, its under your intake I believe, but Im sure its not the problem. yes, only use toyota plugs and wires

Nov 27, 2008 | 2002 Toyota 4Runner

1 Answer

Fuel isnt coming out hte injectors

ok when you turn the key on, you hear the buzzing sound in the tank? if you spray starting fluid into air intake, will the engine fire? there should be a fuel pressure port under hood on fuel rail i believe. if this is vortec style engine, injector assy under intake is possible. somewhat common. pull oil dipstick and smell for fuel. that would indicate maybe the pressure regulator has let go. ck for spark as well, just to be sure youre on the right track.

Nov 10, 2008 | 1997 Chevrolet Tahoe

Not finding what you are looking for?
2003 Kia Sedona Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers


Level 3 Expert

76109 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides