Question about Cars & Trucks

Open Question

I have a ford 2722e 80hp i would like to knowhow many degrees btdc to set the fuel pump

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 645 Answers

SOURCE: have replaced fuel pump, relay & fuel filter.

have you checked to see if you have a bad came or lifter. that would make it backfire. if it kind of spits fuel it maybe cam. if it throws fire than it could be timing like a bad chain.

Posted on Feb 12, 2010

  • 188 Answers

SOURCE: setting the timing on a

Yes, you have to plug the vacumn advance hose.

Posted on Sep 25, 2010

chuckster57
  • 1102 Answers

SOURCE: what should the timing be

Yes ten degrees BTDC is correct for Base timing.

Posted on Feb 01, 2011

chuckster57
  • 1102 Answers

SOURCE: 91 firebird 3.1 v6, if timing is set at 0 degrees

Here is the procedure for setting the timing:
1991-92 Vehicles

See Figure 2
When adjusting the timing, refer to the instructions on the emission control sticker inside the engine compartment. If the instructions on the label disagree with the procedure listed below, follow the instructions on the label.

  1. Locate the timing marks on the crankshaft pulley and the front of the engine.
  2. Clean off the marks and coat them with white paint or chalk, if necessary, so that they may be seen.
  3. Run the engine until it reaches normal operating temperature, then shut off the engine.
  4. With the ignition OFF , connect a tachometer to the distributor, and the pickup lead of an inductive timing light to the No. 1 spark plug wire. Connect the timing light power leads according to the manufacturer's instructions.



WARNING Never pierce a secondary ignition wire in order to connect a timing light. A pierced wire may lead to engine misfiring and driveability problems.

  1. Start the engine. With the engine running at normal operating temperature and all accessories OFF, disconnect the EST bypass connector.

An ECM code will be set when the EST bypass connector is disconnected.
  1. Aim the timing light at the timing mark. The line on the balancer or pulley will line up with the timing mark. If a change in timing is necessary, loosen the hold-down clamp bolt at the base of the distributor. While observing the timing mark, rotate the distributor slightly until the line indicates the correct timing. Use the timing specification on the emission control label in the engine compartment. If this label is missing or damaged, refer to the Tune-Up Specifications chart in this Section.
  2. Tighten the distributor hold-down bolt and recheck the ignition timing to make sure the distributor was not moved when the bolt was tightened.
  3. Turn the engine OFF and remove the timing light and tachometer. Reconnect the number 1 spark plug wire, if disconnected.
  4. Connect the EST bypass connector, then check for and clear the ECM code by disconnecting the negative battery cable for at least 30 seconds.

To prevent ECM damage, the key must be in the OFF position when disconnecting or reconnecting battery cables.

0900c1528008e3bd.jpg

Fig. Fig. 2: EST bypass connector

Posted on Feb 01, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What degree should timing be set on 1984 vw rabbit?


most static settings are 10 degrees btdc
timing lights will be at the 10 degree btdc mark
the workshop manual will have the manufacturers specs but timing can be changed to suit the octane rating of the fuel used but even that is limited to one or 2 degrees either side of the 10

Apr 29, 2017 | Cars & Trucks

1 Answer

How is ignition timing regulated? Car gets 99 BTDC on ignition timing and failed SMOG Test in CA. Listed as GROSS POLLUTER.


something wrong here
with 99 degrees btdc it will not run
have you got it on the correct plug lead
next the timing is regulated by centrifugal advance if electronic or points and by the crankshaft position sensor if ECM controlled ( some after market distributors that are used in place of points units have a small sensor in the distributor that can adjust the timing according to engine rpms, but it cannot make allowances for mixture and so they can advance the timing but not take into account anything else which sometimes results in detonation under certain throttle settings
so initial setting for most cars is 10-12 degrees btdc at idle and with engine rpms set up to 3000 rms it may advance to 25-30 degrees depending on the advance mechanisms
with ECM units the timing is controlled by the crank position sensor and is set to parameters according to engine rpms and air/fuel ratio settings but it still has a basic 10-12 degrees btdc on starting
to fail smog tests you probably do not have a working cat converter and other problems besides timing

Sep 15, 2016 | Cars & Trucks

2 Answers

How do I set injection pump timing


you haven't given which make , model,year of engine type of fuel pump, make of fuel pump and the only clue is the flywheel
the injection timing mark is normally denoted as a lightning symbol and you will find it anywhere between 14 degrees btdc to 22 degrees btdc
or it will be set at the degrees btdc r recommended by the manufacturer
It has to be exact because after that mark will be down on power and too far advanced will melt pistons

May 19, 2016 | Cars & Trucks

1 Answer

Set timing 2.6 ford courier1992petrol


Ignition timing??

10 degrees BTDC.... (+ - 3 degrees tuned bye ear)...

Feb 09, 2016 | Ford Cars & Trucks

2 Answers

Firing order and timing for 292 ford


The firing order is 1-5-4-8-6-3-7-2, distributor turns counter-clockwise. The ignition timing can be set using marks on the vibration damper. The wide mark is TDC (Top Dead Center), each mark after the wide mark represents 2, 4, 6, 8 and 10 degrees before TDC. Set timing 3 degrees BTDC (Before Top Dead Center). In addition, valve timingis set like this: Intake opens: 12 degrees BTDC
Exhaust Closes: 8 degrees ATDC

Feb 04, 2010 | 1981 Ford F 100

2 Answers

We need the timing specs for and 86 2.3 ford mustang


Ignition timing should be set at 10 degrees BTDC (before top dead center), with vacuum advance hose disconnected and plugged, engine idling at 800 rpm or less.

Jan 10, 2010 | 1986 Ford Mustang

1 Answer

Tune up specs needed


1968 Barracuda with a 318cid; The 5th digit of the vin will be (F) for the engine-318 2v rated @ 230hp.

Compression pressure--125-155 max variation 25
Spark plugs--Champion N-14Y @ .035" gap-torqued @ 30ft. lb.
Timing--man. trans @ 5 degrees btdc, auto trans @ 10 degrees btdc.
Points-- .014"-.019" gap--Dwell--28-33 degrees, max variation is 2 @ 1500 rpm--Spring tension--17-20 ounces.
Fuel pump pressure 5-7 lbs. manual pump
Hydraulic Lifters--no valve clearances
Firing order--1-8-4-3-6-5-7-2 counterclock wise rotation
Idle speed--Turn headlights on highbeams and turn a/c off
500rpm for man trans--500rpm auto trans in neutral.

Left bank of the engine (driver's side), 1-3-5-7 Right bank (passenger side), 2-4-6-8

May 22, 2009 | 1983 Plymouth Gran Fury

2 Answers

My 88 Mustang GT boggs on me.


Sounds like the timing is off. When looking at the distributor cap right next to it should be 2 wires with a plug at the end of it. Unplug it and start the car then check your timing . Make sure you mark the crank 10 degrees BTDC. You can bump it to 14 degrees BTDC if you like to gain 10 extra hp. After timing is set turn off car plug spout back in to the 2 wire outlet.(You have to unplug the 2wires in order to time a 5.0 the 2 wires control vaccum)
BTDC-(Before Top Dead Center)

Apr 28, 2009 | 1988 Ford Mustang

1 Answer

RPM at idle, and T.D.C degree


5.0 L with CFI = 550 rpm

5.0 L with CFI = 10 degrees @ 550 rpm

5.0 L with a 4bbl carb = 700 rpm

5.0 L with a 4bbl carb Calif. = 10 degrees btdc @ 800 rpm

5.0 L with a 4bbl carb Fed. = 12 degrees btdc @ 800 rpm

cheers mate !

Jan 10, 2009 | 1986 Ford Thunderbird

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

160 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...