Question about 1993 Chevrolet C1500

1 Answer

Got 93 chevy 1500 may be the 454 it has decals>>>> need to change the axle seals(rear)>> the bolt that you usualy have to take out is not there.. empty hole???? even if you could get the through pin to slide it can't go past the ring gear??????need help/

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 14,036 Answers

PINION SHAFT PROBABLY GAULDED DAMAGED BY THE BOLT BEING MISSING NOT IN PLACE.IT WOULD TAKE LARGE VISE GRIPS ATTACHED TO SLIDE HAMMER TO GET PINION SHFT OUT.YOU NEED TO GO TO AUTO PARTS STORE OR DEALERSHIP TO BUY ANOTHER PINION SHAFT OLD ONE MORE LIKELY DAMAGED.

Posted on Jul 10, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace rear axle seal on a 1999 chevy Silverado?


Watch the You Tube Video

Remove the rear axle cover
Remove the carrier bolt & pin
Push the axles in
Remove the C-Clips
Pull the Axles
R & R the housing end seals

Sep 30, 2014 | 1999 Chevrolet Silverado 1500

1 Answer

How to change the outer seal near da tire on a 1985 chevy silveraldo rearend


you need to remove the cover in the middle of the rear axle rotate the drive shaft until you see a bolt with a 5/16 head on it slide out the pin that the bolt held in remove the c clip that holds the axle in slide out the axle and replace the seal you should do both sides while its apart then put it back together and fill threw the plug on the front side that uses a 3/8 drive

Mar 30, 2012 | Cars & Trucks

1 Answer

How do i change da rear other seal on the rearend of a 1985 chevy silverado


Replacing axle seals requires removing the differential cover,removing the spur gear bolt/shaft,removing the C clip,then sliding the axle out.You will have to press the bearing off of the axle to remove the seal,which usually will break the bearing(might as well replace it anyway on an '85).Removing and replacing the bearing should be done with a shop press.

Mar 30, 2012 | 1983 Chevrolet Silverado

1 Answer

How do you replace the rear axle seal & bearing from a 1996 chevy 2wd 1500


remove the brake shoes, should be 4 bolts holding the axle in, pull out axle and bearing should be there also replace real seal

Jun 16, 2010 | 1996 Chevrolet C1500

3 Answers

How to replace rear Axle seal on 4x4 chevy


this is very hard if you do not know what you are doing. Ill try to step you through this
  • pull wheels
  • drain pun-kin case
  • pull rear cover
  • in between the spider and axle sets pull C ring with needle nose pliers
  • pull hub and axle out CAREFULLY as there are roller bearings on the end of the axle housing
  • pull seal out at the end of axle housing
  • tap in new seal CAREFULLY and straight DO NOT BEND IT or it will be junk
  • replace axle carefully as the roller bearings are still there
  • replace C clip to original position
  • replace axle diff cover and replace the gasket with a new one
  • refill diff case
  • install tire
  • your good to go

May 03, 2010 | 2002 Chevrolet Silverado

2 Answers

How do you change rear axle seal in a chevy pickup


To change the rear seal, yo will need to raise and support the rear of the vehicle. Remove the wheels and drums or rotors (depending on drum or disc brakes.) Remove the rear differential cover bolts and the cover (have a drain pan under the differential) You will likely need to turn the driveshaft so the center pin bolt is acessible at the back or the differential. This is a 5/16" (or 8mm) bolt that is on the right (passenger) side of the differential carrier assembly. I recommend a new bolt be installed here on reassembly. Once the retaining bolt is out, slide the center pin out enough to allow the axle shafts to be pushed in toward the center of the diff. to remove the "C" clips that retain the axle shafts in the carrier assembly. Be careful if you happen to pull the center pin all the way out not to allow the carrier assembly (has the ring gear mounted on it) to turn, as this can rotate the spider gears out of alignment causing a headache on reassembly. With the "C" clip removed the axle shaft can be pulled out of the diff. Inspect the bearing area of the shaft for rust, pitting, or scoring. Remove the old seal and carefully install the new one. Reverse proceedures to install. Take care to note the "C" clips and center pin bolt are properly reinstalled. Fill with 2.5 to 3 quarts of rear axle grease for you vehicle.
good luck.

Oct 25, 2009 | 2000 Chevrolet Silverado

3 Answers

How to replace a transmission output seal 93 buick lesabre


you have to raise vechicle.use jack stands.block rear wheels.apply parking brake.when loosen axle nut.its more easier to leave wheel on.let vechicle weight hold wheel from turning while you loosen axle nut.you need to get a 1/2 break bar or large ratchett wrench with a deep socket .you need to buy socket use to remove axle nut a regular socket would probably break.when you remove the axle nut.remove brake caliper and brake pads.set them aside dont disconnect brake caliper.get a piece of wire to hang it out the way.dont use brake hose.could damage it. remove brake caliper support bracket then the rotor.get a hub removing tool remove hub.then loosen hub and bearings bolts .then remove shield hub and bearings assembly with O-ring.disconnect ball joint from steering knuckle using the proper tool.remove the halfshaft assembly and tap the seal from the steering knuckle.remove the steering knuckle from the hub.now that drive axle out the way.get the seal removing tool.its a flat tool with two hooks on it.to pry seal out transmission.or you can use a small chisel to clapse the seal but be careful dont damage the seal housing.when installing new seal coat it with transmission fluid.drive it in using a large socket.if you are reusing same axle replace circlip on the end of it.now putting back together.install a new hub and bearing seal in the steering knuckle with a seal installer tool .install steering knuckle to the strut.lubricate the hub and bearings with grease.install halfshaft.connect ball joint to the steering knuckle .install a new O-ring around the hub and bearing assembly.install hub and bearing assembly into the steering knuckle.tighten bolts to 75 ft lbs.install rotor then brake caliper support bracket bolts 120 to148 ft lbs.this is mounting bracket bolts only not the caliper bolts to brake shoes.put brake shoes and caliper back on torque 38 ft lbs.install shaft washer the axle nut to 180 ft lbs.tighten much as you can.before setting car on ground.to torque it to 180 ft lbs place car wheel back on set it down so the car weight keep wheel from turning.i hope this information works out for you good luck.and work safe.

Jun 27, 2009 | 1993 Buick LeSabre

1 Answer

Does anyone know how to change seals on rear diff on 2003 frod expedition


if you need to change the axle seals here is the process. You need to remove the rear wheels. Remove the brake drums if so equipped. Remove the rear cover on the differential. Turn the differential until you find the bolt that holds the cross shaft in place. Remove the bolt and pull the cross shaft out. Then you will see the axle ends. Push the axle in towards the center of the axle. You will need to remove a C clip retainer from the axle end. You can then remove the axle and gain access to the seal. Repeat the process on the opposite side. Then reverse the disassembly process. Place the cover back onto the differential housing and refill the differential. Good luck.

Mar 03, 2009 | 2003 Ford Expedition

1 Answer

How to Change Rear Axle Seal?


When you take the rear drum off, look where the axle goes in and if there are 4 bolts around it, you don't have to go into the diff. If there are no bolts holding the axle in, then get a repair manual to guide you through the steps. The seal on an axle that is bolted in place will have a collar that needs to be pressed off and a new one back on. These seals can be bought at a local partsd house.

Nov 09, 2008 | 1989 Jeep Wrangler

1 Answer

98 Ford F-150 2WD rear axle removel


The Ford is similar to the Chevy. Same procedures apply. Same retaining bolt in center section needs to be removed to allow cross shaft to come out. Same technique in removing spider gears. Same "C-clip" retainers on axle ends. you shouldn't have any issues.

Oct 19, 2008 | 1998 Ford F150 Regular Cab

Not finding what you are looking for?
1993 Chevrolet C1500 Logo

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...