Question about 1991 Jeep Wrangler

2 Answers

Slave cylinder leaks

Clutch slave cylinder leaks what does it consist of to change it

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 1,940 Answers

Remove the bolts holding the slave cylinder to the transmission. Disconnect the hydraulic hose. Reconnect hydraulic hose to new slave cylinder, and install the slave cylinder in it's original position.

Now proceed to bleed the line through the slave cylinder until a solid stream of fluid comes through, and the pedal pressure becomes firm.

Posted on Jul 10, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 593 Answers

The slave cylinder and the throwout bearing are the same unit. To replace it is not a small job. The transmission and transfer case have to
be removed to access it. The job is = to 3/4 of a clutch replacement,
and requires the proper equipment and more than a little bit of automotive knowledge to do the job safely. If you wan't to take it on, you
can post again or give us a call and we can give you the how to's.
Hope this helps.

Posted on Jul 10, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why is my clutch feel like there is air in the line it seems to have alot of play.


Air in the hydraulic clutch release System. The system consists of the clutch master cylinder, line, hose and clutch slave cylinder. Check the level at the clutch master cylinder. The fill reservoir is along the firewall on drivers side with a black cap. It uses DOT 3 brake fluid. Add fluid if low and pump pedal. If low you have a leak. If full you have a master cylinder internal seal bad so you have to have the master cylinder for the clutch replaced.

Jul 24, 2014 | 1996 Pontiac Sunfire

3 Answers

I just replaced clutch on 1993 Honda accord ex and the release cylinder isn't pushing the release bearing enough to shift when car is running


I really need more info such as...Mileage,did you do the job yourself,if so was the slave cylinder and or clutch master cylinder changed and did you bleed the system..?...So I will explain without knowing,,...Before a clutch wears completely out we find ourselves constantly working the clutch pedal stressing all clutch system components..In most cases I have looked closely and found slave cylinder and clutch master cylinder leaking ..however the slave cylinder can wear out without leaking..Most importantly the fluid itself wears out every 15 to 20,000 miles.. You don't notice but the fluid gets thousands of tiny air bubbles in it and makes the clutch weak and spongy..(Same with brakes)..You should always bleed system with an assistant just as you would a brake system..,This alone will cause the problem you are experiencing...If you already know that and you have bled the clutch system then you know the slave cylinder is at fault..(UNLESS THERE WAS SOME TYPE OF MISALIGNMENT WITH RELEASE BEARING....YOU SHOULD ALWAYS CHANGE RELEASE BEARING WITH FORK WHEN DOING A CLUTCH SERVICE..)...I assume you did...I would inspect for leaks..,Bleed it again if no leaks...If that don't help and no leaks are found change slave cylinder and or master cylinder.....I hope this helps........Brooks/Metalpoet.......

Jun 13, 2014 | Cars & Trucks

2 Answers

Lost resistance on clutch pedal and hard to change gears also when topping up clutch fluid it does`nt last that much and leaks from slave cyclinder


If the slave cylinder is leaking, replace the slave cylinder. You are loosing hydraulic pressure in the clutch and is the reason why it is not engaging correctly.

Apr 13, 2011 | 2001 Honda Accord

1 Answer

2001 mercury cougar, master cylinder ran dry because slave cylinder below is leaking at the firewall. I filled the master cylinder and tried bleeding the clutch at the transmission until fluid stream...


No, you don't need to replace the clutch itself.
Don't be surprised if the slave cylinder replacement doesn't fix it.
Could be the master cylinder.

Sep 12, 2010 | 2001 Mercury Cougar

2 Answers

Having problems with the clutch in my 1998 Ford Ranger. There is no freeplay, and it is very difficult to shift. Do I need to adjust the clutch? If so, how do I adjust it?


The clutch is not adjustable,it is a fluid clutch.It has to be a leak,or the slave cylinder,and,or, the master cylinder are bad,It does not have to be leaking to be bad,but it is one of the two.Rate please,thank you.

Jul 12, 2010 | 1998 Ford Ranger SuperCab

2 Answers

Clutch fluid leaking inside of trans housing on a 98 s10


do you mean a manual model ?? is the slave cylinder inside the bell housing ??if so renew it

Dec 27, 2009 | 1998 Chevrolet S-10 Pickup

5 Answers

Stuck clutch pedal on a Mazda B series truck


Replace both clutch slave and master cylinders, and bleed well. I've also had this happen.

Jul 11, 2009 | 1988 Mazda B2200

1 Answer

Clutch pedal goes to floor


Its sounds like a bad clutch cylinder or bad slave cylinder or fluid leaking. First check brake fluid level in clutch master , and check for a leak in clutch system. If there are NO leaks, then you either have a bad clutch cylinder or a slave cylinder. Bleed clutch at bleeder screw on slave cylinder and make sure there is pressure from master cylinder. If there is pressure then slave cylinder may be bad replace slave and bleed and that should take care of you problem. If master is bad then replace bleed system ad you should be good. Contact if you need more help. Thanks for using FIX YA.

May 16, 2009 | 1988 Honda Accord 4 Door

1 Answer

Clutch 1998 toyota tocoma


Replace master cylinder

Mar 11, 2017 | 1998 Toyota Tacoma

Not finding what you are looking for?
1991 Jeep Wrangler Logo

529 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...