Question about 2007 Jeep Liberty Sport

1 Answer

I need to know how to replace a light bulb in the rear.It is a brake light

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 524 Answers

Hi..
follow these steps.

1.switch off the car
2.remove the tai light cover using screw drivers
3.remove the bulb ib the socket
4.replace with new bulb .make sure you choose than right power bulb or else it wont work
5.put back the cover

please vote me if the infomationwhich gave you was useful by clicking the thumb on your lower side of your page.

Posted on Jul 10, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 pt cruiser--no brake lights--have tail lights--replaced brake light switch 3 times--brake lights work for about a week--ideas?


I would like to know if you have turn signals working in the rear. These are the same bulbs that brake lights use. If you don't have turn signals, then you need to replace the bulbs. If you do, then there is probably a wiring issue, or a circurt breaker problem. Hope this helps?

Aug 20, 2014 | 2002 Chrysler PT Cruiser

1 Answer

Replaced the brake light switch completely, but as soon I hit the brake pedal, the brake light warning light comes on again indicating that there is a light out in the rear. But all the lights are working,...


If this is a newer lexus, then its very clever. It WILL be a blown bulb, but when a bulb is out, the car lights the next nearset bulb to substitute. Have a closer look at the rear lights and check all the bulb filaments by eye.

May 29, 2011 | Lexus GS 300 Cars & Trucks

1 Answer

My brake lights will not function on my 2000 grand caravan.All of the bulbs are new my rear lights work my reverse lights work but my brake lights will not


The bulbs could still be the problem since they are double filament bulbs.If your high brake light work but not the low ones the replace the bulbs.If none in the rear work then you may need a brake light switch(on the brake pedal linkage).If this is not the case the check for power to the brake light side of the bulb and repair the broken brake light wire.

Oct 06, 2010 | 2000 Dodge Caravan

1 Answer

What bulb do i need to replace in order to fix the rear brake light


automatic answer would be the rear brake light bulb. So much for being funny. Look at the bulbs the bulb that you will want to replace with have 2 elements inside the bulb. The single element bulb is for your tail lights.

May 03, 2010 | 2002 Oldsmobile Silhouette

1 Answer

How do i change a brake light bulb on 2000 vw jetta?


Removing:
  • Switch off all electrical consumers, switch off ignition key and remove ignition key.
  • Remove rear luggage compartment side panel trim (left or right).
98971821.gif
  • Remove 3 nuts, arrows, and remove housing.
  • Remove bulb holder.
Installing:
  • Install bulb holder.
  • Insert housing into body opening.
  • Tighten nuts.
  • Install applicable rear luggage compartment side panel trim.
Rear Light Bulb Holder Removing And Installing:
Removing:
  • Disconnect electrical connector.
  • Depress retainers, arrows, and remove bulb holder.
98971817.gif Installing:
  • Install in reverse order of removal.
And the Center Mounted Brake Lamp.
High mount Brake Light Removing And Installing:
The high mount brake light is installed in the rear shelf.
98971288.gif Removing:
  • Switch off all electrical consumers, switch off ignition key and remove ignition key.
  • Disconnect electrical connector from high mount brake light.
  • Remove rear shelf
  • Un-clip high-mount brake light from rear shelf, arrows.
  • Install in reverse order of removal.
NOTE: The bulb holder base plate contains soldered- in light emitting diodes (LEDs) that are not replaceable. In the event of LED malfunction, replace complete bulb holder.
Additional

Mar 13, 2010 | 2000 Volkswagen Beetle

1 Answer

Accessing the rear hatch brake light on a 1999 Ford Expedition


There should be 2 screws holding the lenses on for the hatch light, remove those and cover comes off. The plate lights, access them under the rear bumper, they twist and pull out, then just pull the bulb out the connector. The running board light, under board, which will take the light assembly out, or a small flat head screwdriver, pop the lens off the top of board.

Dec 27, 2009 | 1999 Ford Expedition

2 Answers

Rear turn signals and brake lights out. Front signals and rear tail lights work fine.


the brake lights and the rear turn signals should be the same bulb check the bulbs to make sure they are not blown does your third brake light work if all brake light are out and the bulbs are good check the brake light switch on the brake pedal

Nov 04, 2009 | 1986 GMC C1500

1 Answer

BURNING THE REAR SIGNAL LIGHT BULB EVERY 3 OR 4


I bump into the same problem wrong brake light bulb
try 3157LL . See if you have this brake bulb number

If this is not the case replace the bulb plug (pig tail).
Call dealership for this part
I see this problem before also.

Let me know if this help....

Sep 29, 2009 | 2003 Chrysler PT Cruiser

3 Answers

The brake lights on my 1999 saturn sl do not work. The bar on the rear window functions. The bulbs and fuse is ok--what is the problem


does the third brake light work when braking ? the bar on the rear window? if not replace brake light switch on brake pedel

Jul 03, 2009 | 2000 Saturn SL

2 Answers

No brake lights but 3rd light works all fuses are good


Sounds like a broken wire somewhere.
Since the middle brake light works I would suspect it is somewhere in the trunk or close to the back seat.
Buy or make a tester. A 12v light with a clip on one wire that you clip to a good ground on the car the other wire with a sharp point. Turn the turn signals on then poke wire to rear lights until tester lights. When tester lights you know the break is somewhere inbetween the tester and the brake lights.

Hope this helps.

Stan

Apr 16, 2009 | 1985 Buick Skylark

Not finding what you are looking for?
2007 Jeep Liberty Sport Logo

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...