Question about 1983 Chevrolet Chevy

1 Answer

Head lighs just installed new head lighs on a 84 chevy custom 10 and nothing happens

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 409 Answers

Sounds like you have a bad dimmer switch. That switch is mounted on the top of the steering column but is not too bad to change. You will need to take out the panel under the steering column and remove the nuts holding it up to allow it to dorp a few inches. With that done its just a matter of 2 bolts to remove the switch.

Posted on Jul 10, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

High beam in 2007 Impala pointing down after changing bulb.


Check for proper installation if you you install it properly you should have adjust the head light again by two nut behind the head light one for vertical another for horizontal

Dec 04, 2013 | 2007 Chevrolet Impala

1 Answer

Blown head gasket. Need head bolt, rocker arm removal and reinstall torque specs, and what order to remove/install.


No check the intake manifold gasket first that is most likely your problem and you don't have to remove the heads to do this . Over heat these engines once and this will happen and its a lot cheaper and far less work to do the intake then the heads happens all the time its a problom with chevy engines

Aug 22, 2011 | 1999 Chevrolet S-10 Pickup

1 Answer

1983 Chevy S-10 4.3L V6 New Battery, Will not turn over. There is nothing happening at all.


I know this sounds weird,but when you installed the new battery did you remove the ground and positive protective post covers? I had a customer tow their vehicle in to the shop for a no-start after battery replacement and they put the negative post on with the cover still attached to the battery and of course it would not start...lol....If this is not an issue,check the ground wires on the engine and the body ground near the battery for looseness or corrosion.Same with the terminal ends.Hope this information helps,
KEN

Oct 08, 2010 | 1983 Chevrolet S-10

1 Answer

I need the wiring layout for an 1984 chevy s-10 ignition module


Got an 84 shop manual with wiring

What do you need ?

Also got a 1984 S10 Blazer since new

Oct 08, 2010 | 1984 Chevrolet S-10

2 Answers

1998 chevy s10 will not start


engine wont run on an chevy s-10 pick-up 1998. 4cyl

Feb 14, 2010 | 1998 Chevrolet S-10 Pickup

1 Answer

What is the torque settings on the head bolts for 2002 nissan x-terra 2.4litre?


① Step 1: 22 ft. lbs. Step 2: 59 ft. lbs. Step 3: Loosen completely then retorque to 22 ft. lbs. Step 4: 18-25 ft. lbs. Step 5: Plus 86-91 degrees ② 10-12 ft. lbs. plus 60-65 degrees or 28-33 ft. lbs. ③ The cylinder heads and the lower intake manifold are installed together Step 1: Tighten the cylinder head bolts to 22 ft. lbs. Step 2: Tighten the cylinder head bolts to 43 ft. lbs. Step 3: Loosen the cylinder head bolts completely Step 4: Tighten the cylinder head bolts to 84 inch lbs. Step 5: Tighten the intake manifold fasteners to 35 inch lbs. Step 6: Tighten the intake manifold fasteners to 13 ft. lbs. Step 7: Tighten the intake manifold fasteners to 12-14 ft. lbs. Step 8: Loosen all intake manifold fasteners completely Step 9: Tighten the cylinder head bolts to 22 ft. lbs. Step 10: Tighten the cylinder head bolts 60-65 degrees Step 11: Tighten the cylinder head sub-bolts to 80-105 inch lbs. Step 12: Tighten the intake manifold fasteners to 35 inch lbs. Step 13: Tighten the intake manifold fasteners to 78 inch lbs. Step 14: Tighten the intake manifold fasteners to 70-84 inch lbs. ④ 10-12 ft. lbs. +60-65 degrees ⑤ Step 1: 72 ft. lbs. Step 2: loosen completely to 0 ft. lbs. Step 3: 29 ft. lbs. Step 4: Plus 75 degrees clockwise Step 5: Plus 75 degrees clockwise ⑥ Step 1: bolts 11-22 19 ft. lbs. Step 2: bolts 1-10 29 ft. lbs. Step 3: bolts 1-10 Plus 60-65 degrees ⑦ Step 1: 20 ft. lbs. Step 2: loosen to 0 ft. lbs. Step 3: 14 ft. lbs. Step 4: Plus 85-95 degrees ⑧ Step 1: 31 ft. lbs. Step 2: Plus 60 degrees ⑨ 83 inch lbs. ⑩ Stud bolt: 11 ft. lbs. Nuts: 31 ft. lbs. ⑪ Step 1: 72 ft. lbs. Step 2: loosen completely to 0 ft. lbs. Step 3: 29 ft. lbs. Step 4: Plus 90 degrees clockwise Step 5: Plus 90 degrees clockwise ⑫ Bolts: 17-24 (M8) 16 ft. lbs. Install rear main seal Bolts: 1-16 (M10) 26 ft. lbs. Bolts: 1-16 (M10) Plus 90 degrees clockwise ⑬ Step 1: 33 ft. lbs. Step 2: Plus 84-90 degrees clockwise ⑭ Intake manifold collector: Bolts and nuts: 8 ft. lbs. Stud bolts: 61 inch lbs. ⑮ Intake manifold: Bolts and nuts: 5 ft. lbs. and than to 21 ft. lbs. Studs: 8 ft. lbs.

Jan 10, 2010 | 2002 Nissan Xterra

2 Answers

1977 chevy silverado starter


does the new starter work has it been tested? is the wires on your starter in the correct position? Is your battery fully charged? did you install it correctly?

May 23, 2008 | 1994 Chevrolet S-10

Not finding what you are looking for?
Cars & Trucks Logo

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...