Question about Ford Mustang

1 Answer

I only get a click when i turn thekey on my 89 mustang

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

Either you have a dirty cable connection (likely negative battery cable) or it is loose. Dirty connections will cause this. Also bad solenoids will cause this.

Posted on Jul 09, 2010

  • 2 more comments 
  • icandothis_j Jul 09, 2010

    i actually have 2 mustangs, i switched the selinodes last night, no change. i pulled the AOD and replaced with T5 this past weekend, all terminals are freshly cleaned, greased up and tight. i pulled the starter just now, hooked up battery cables direct to starter, nothing. before i spend 75 for new i am looking for a second opinon doctor. thanks for your next reply.

  • Nate Stansfield
    Nate Stansfield Jul 09, 2010

    Are you getting full power from the ignition switch to starter? Have you tested the starter relay? Checked the ignition wire?

  • icandothis_j Jul 09, 2010

    if i am hooking battery cables direct to the starter and it does not respond how would wiring have anything to do with it?

  • Nate Stansfield
    Nate Stansfield Jul 09, 2010

    If you are hooking battery directly to starter and it is not responding, than the starter is bad or the arm that moves out drive gear is stuck

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

While driving my mustang 89 5.0 gt Manuel it shut down now it'll jt turn over but won't crank


check your impact switch, may need reset, make sure button on switch is depressed

Oct 31, 2015 | 1989 Ford Mustang

1 Answer

85 mustang fuel pump not primeing


See if the oil pressure switch has 3 prongs. If so and it's leaking oil, that may be the problem. I can't recall what year they stopped doing that switch but my '89 had it. Aside from that, check the fuel pump relay. It can click and still not supply power to the pump.

Apr 02, 2014 | Ford Mustang Cars & Trucks

1 Answer

My 89 mustang won't run with the maf sensor


you need to replace the mass airflow sensor it is defective for that year should be cheap but most likely will need to be ordered


please leave 4 thumbs if it helps

May 10, 2011 | 1989 Ford Mustang

1 Answer

How do you remove 89 convertible mustang rear seat


hit it hard (with the side of your hand or palm) at the bottom of the seat on the right and the left to relase the spring retainers, run a putty kniofe under the seat edge to locate the spring retainers

Apr 02, 2010 | 1989 Ford Mustang

1 Answer

89 ford mustang v-6 is the c-clamp going to seat the caliper?


yes it will, just turn in slowly it will set piston bck in,not much force needed if it is hard to seat piston back in caliper you may have a bad hose or caliper, the way to find this out is open bleeder and if its easier to colapse the piston then its a hose if it doesnt make a diffrence then its a bad caliper, but this is only if you have a problem the c clamp will do the job, hope this is helpful.

Feb 19, 2010 | 1989 Ford Mustang

1 Answer

Why does my 89 mustang gt blow black on the grass an stals


your gas to air ratio is off. Too much gas not enough air,flooding,check if the gaskets are tight for the fuel area.

Jul 22, 2009 | 1989 Ford Mustang

1 Answer

How to install a ignition swicth for 89 mustang gt


try moveing your stearnwheel back and forth and trun the key at the same time. but i hate to tell you will have to re place the switch. some time down the road have a nice day

Mar 26, 2009 | 1989 Ford Mustang

3 Answers

89 ford mustang


Hi

Why not Google..... for a local Mustang Enthusiasts Club ?

Good Luck !

Please give a FixYa Rating Please ....I need to be a Guru !
John.

Feb 04, 2009 | 1989 Ford Mustang

1 Answer

Blower Motor for 89 Mustang


i've replaced three heater cores on a mustang, the only way to get to them is to remove the dashboard i believe the only way to get to the blower motor is the same way, located behind the glove compartment.

Sep 02, 2008 | 1989 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...