Question about 2000 Nissan Altima

1 Answer

A/c stopped working. fuses are good. i took out the glove compartment and ran the a/c and the blower motor was not running. the a/c sounds like its working. Could it be a bad blower motor. Could it need a new relay? Could it need a new resistor?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

YOURE ON THE RIGHT TRACK ,ITS NORMALLY A RELAY.

Posted on Aug 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Blower Motor Not Working properly


check "amp" at the blower motor! if the "amp" its to high , you better replace the blower motor! It will damge your blower control module soon also!!

Mar 15, 2016 | Cars & Trucks

1 Answer

Initially I heard a tapping sound around the glove box when I put on the fan. I tried to locate the source of the sound but unsuccessful, so, I decided to run the fan on high speed. It ran and then stopped...


There is a 50amp heater fuse, then a heater relay. Once power gets to the blower motor, the resistor and fan switch provides the ground circuit.

Feb 13, 2014 | 2001 Toyota Camry

1 Answer

Heat and air condition fan stopped working on my 2004 Dodge Dakota, does not blow, ice is comming in and i need to be able to defrost my windshield and heat my truck


First thing to check is the fuse. There will be one under the hood and another in the interior fuse box. The 2004 model does nt have a relay. If the fuse is good, you need to check to see if the blower motor is good. The motor is located under the glove compartment area of the dash, near the firewall. Disconnect the harness from the blower motor, and using jumper wires, apply voltage directly to the blower motor contacts. If the blower motor works, then the switch is bad. If the blower still does not work then the motor is bad.

Mar 04, 2011 | 2004 Dodge Dakota

1 Answer

My 1988 Ford Tempo's heater fan is not working. I can feel heat at the windshield vents,but the fan wont come on. I have jumped the fan speed switch with a paper clip--and blew a fuse--and checked the...


your circuit is simple--I will paste it below. suspect the blower has shorted and caused the switch to burn up. remove the blower and hotwire it to the battery to see if it works. If not, replace the blower. Then run continuity tests on the swoitch and replace switch if bad. If you have questions, please let me know. Here is procedure for taking blower out:


REMOVAL & INSTALLATION With Air Conditioning

  1. Disconnect the negative battery cable.
  2. Remove the glove compartment door and glove compartment by removing the retaining screws and bolts. Push the sides of the glove box in to free the drawer from dash panel.
  3. Loosen the instrument panel at the lower right hand of the glove compartment opening. This is on it necessary if the panel is in the way of the motor housing.
  4. Remove the retaining screws securing the ducting around the blower motor.
  5. Remove the clip securing the blower motor fan blade to the motor arm. Remove the fan blade from the motor.
  6. Remove the blower motor mounting plate from the evaporator case by unscrewing the retaining screws.
  7. Rotate the motor until the mounting plate clears the edge of the glove compartment opening and remove the motor.
  8. Remove the wire harness from the rear of the motor.
  9. Inspect the fan blade for broken edges or cracks. Replace if needed.

To install:
  1. Connect the wire harness to the rear of the blower motor.
  2. Install the motor into the case and secure with the retaining screws.
  3. Position and fasten the fan blade to the blower motor arm. Secure with the clip.
  4. Secure the blower motor outer housing to the duct assembly with the retaining screws.
  5. Install the instrument panel at the lower right hand side if removed earlier.
  6. Install the glove compartment door and glove compartment.
  7. Connect the negative battery cable.
  8. Run blower motors to make the motor works correctly.
Without Air Conditioning
  1. Disconnect the negative battery cable.
  2. Remove the right ventilator assembly.
  3. Remove the hub clamp spring from the blower wheel hub. Pull the blower wheel from the blower motor shaft.
  4. Remove the blower motor flange attaching screws located inside the blower housing.
  5. Pull the blower motor out from the blower housing (heater case) and disconnect the blower motor wires from the motor.

To install:
  1. Connect the wires to the blower motor and position the motor in the blower housing.
  2. Install the blower motor attaching screws.
  3. Position the blower wheel on the motor shaft and install the hub clamp spring.
  4. Install the air inlet duct assembly and the right ventilator assembly.
  5. Connect negative battery cab
  6. Check the system for proper operation.

36d4b25.gif

Oct 21, 2010 | 1988 Ford Tempo

1 Answer

Air conditioner blower not operating. Checked fuse. It is good.


If its the climate contol knobs, 1-5 dial speed ,i had no air or heat! my blower not working .there is a heater-blower relay located on blower motor housing. take off cover below glove compartment. you can go to auto zone for $30 and get one plug in the pigtails. you can also check blower motor with a voltmeter,but i didnt have.So 3 screws i took off and blower motor came down. i hooked 2 alligator clips to blower motor and touched 2 to the battery 1 to positive and 1 to negative ,blower motor spun . it was good ,relay was bad. $30 CHEAP FIX AND 1 HOUR OF CRAMPED SPACE !!! THIS IS FOR MANUAL KNOBS

Jul 12, 2010 | 2002 Chevrolet TrailBlazer

3 Answers

I have 03 honda accord blower motor will not come on any heating or cooling setting. air cond compresser will run for acople of seconds


There should be a fuse in the dash fusebox, or a relay in the engine compartment if those are both good the the blower motor is bad

Apr 11, 2010 | 2003 Honda Accord

2 Answers

I have a 2004 GMC Yukon with auto climate control. The front a/c is working but the fan will not come on. The rear a/s works fine. Checked fuses, they are all good. Any suggestions?


It's most likely your blower motor control module. Easy fix! Remove the kick plate under the glove compartment and the module is right next to your blower motor - remove the two screws and it will drop right out. Disconnect the wire harness (2 wires) and replace. Good luck!

Jul 28, 2009 | 2003 GMC Yukon

1 Answer

Heater blower does not work on 93 Altima on any speed.


It's behind the glove compartment. I had to remove about eight screws to pull of the glove compartment door and glove compartment molded plastic trim. If you are looking for the blower motor resistor. I found it. The blower motor is the roundish part on the far left hand side of the glove compartment opening. Out of the bottom of the blower motor are four wires in a common cable with a connector at the end. Disconnect this common cable connector. It is connected to the blower motor resistor with two screws. It will look like you are removing a connector, but the back side of this part has a what looks like a fin cooler. That part in your hands is the resistor (really) The part number will be on the connector P/N 27150 1E400

Jan 05, 2009 | 1993 Nissan Altima

3 Answers

Inside fan has just stopped working


It could mean a new fan,but most systemes use a blower motor resistor to control the speeds of the fan which could have died and is lockated in the air box for climait control.

Aug 17, 2008 | 2004 Saab 9-3

1 Answer

Blower motor


Blower motor is located under the passenger side of the dash behind the glove compartment.

Jun 14, 2008 | 1990 Dodge Dynasty

Not finding what you are looking for?
2000 Nissan Altima Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...