Question about 1991 Geo Tracker

1 Answer

Took the water pump off of a 1991 geo tracker and a spring fell out of timing belt cover. Do you know what bolt the spring attaches to

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,092 Answers

Hope this helps you, good luck.


took the water pump off of a 1991 geo tracker and - bd59346.gif

Posted on Jul 09, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the timing belt and water pump on my 1991 sun bird. 2.0 liter engine


Water Pump: Remove timing belt rear protective covers, Remove lower radiator hose from water pump. Remove water pump attaching bolts then the water pump and sealing ring, Clean engine block and water pump sealing surfaces, then apply a 3/32 inch of RTV sealant to sealing surfaces. While RTV sealant is still wet, install water pump. Tighten attaching bolts finger tight. Install lower radiator hose on water pump, then belt rear protective covers. Install timing belt

Jan 18, 2013 | Cars & Trucks

1 Answer

Need R&R information to replace for waterpump Geo Storm 1993 4 cyl


Hi!!
Here is the Info you requested:
WATER PUMP REMOVAL & INSTALLATION
Except Twincam Engines See Figures 1 and 2
  • Disconnect the negative battery cable and drain the cooling system.
  • Loosen the power steering pump adjustment bolts and remove the drive belt.
  • Remove the timing belt; refer to the procedure later in this section.
  • Remove the tension pulley and spring.
  • Remove the water pump mounting bolts, water pump and gasket. Clean the mounting surfaces of all remaining gasket material.
  • To install, reverse the removal procedures. Tighten the water pump bolts to 17 ft. lbs. (23 Nm) and the tension pulley to 30 ft. lbs. (40 Nm).
  • Connect the negative battery cable and fill the cooling system, then start the engine and check for leaks.

FIG 1 1kbron_114.jpg
FIG 2 1kbron_115.jpg

Twincam Engines See Figure 3
1.6L DOHC ENGINE
  • Disconnect the negative battery cable and drain the cooling system.
  • Support the engine using a suitable floor jack and remove the right front engine mount.
  • Remove the engine mount bridge and the upper timing belt cover.
  • Remove the power steering belt and the lower timing belt cover.
  • Loosen the timing belt tension pulley and remove the timing belt.
  • Remove the power steering pump and bracket.
  • Remove the water pump attaching bolts, then the water pump from the vehicle. Thoroughly clean all remaining gasket material from the mating surfaces.
  • Reverse procedure to install and tighten the water pump bolts to 17 ft. lbs. (24 Nm). Connect the negative battery cable and refill the cooling system. Start the engine and check for leaks.
FIG 3 1kbron_116.jpg
1.8L ENGINE
  • Disconnect the negative battery cable and drain the engine cooling system.
  • Remove the timing belt covers; refer to the procedure later in this section. Loosen the timing belt tensioner pulley bolt, then remove the belt from the water pump pulley.
  • Remove the 2 bolts from the power steering pump bracket, then position the pump aside with the lines still attached. Be careful not to kink or damage the steering fluid lines.
  • Remove the water pump mounting bolts, then remove the pump from the engine. Thoroughly clean the gasket mating surfaces of all remaining gasket material.

To install:
  • Install the water pump using a new gasket, then tighten the retaining bolts to 18 ft. lbs. (24 Nm).
  • Position the power steering pump assembly, then install the retaining bolts and tighten to 25 ft. lbs. (34 Nm).
  • Install the timing belt to the pump pulley, then tighten the tensioner pulley bolt to 30 ft. lbs. (40 Nm).
  • Install the timing belt covers.
  • Connect the negative battery cable and fill the cooling system, then start the engine and check for leaks
Good Luck!! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa.

Mar 11, 2011 | Geo Storm Cars & Trucks

1 Answer

How to replace the water pump on a 1992 geo tracker 1.6 liter engine


Water Pump - REMOVAL & INSTALLATION
During these procedures, identify all components removed from the engine so that they may be reinstalled in their original positions. If discarding the old components so that new components can be installed, identifying the old items is not necessary.


1.3L and 1.6L Engines

  1. Remove the timing belt cover, timing belt, tensioner, plate and spring.
  2. Remove the water pump mounting bolts.
  3. Remove the one (1.6L MFI engines) or two (1.3L and 1.6L TFI engines) small rubber seals from between the water pump and the oil pump, and the water pump and the cylinder head.
  4. If necessary for clearance, remove the oil level dipstick tube retaining bolt from the engine block and the alternator adjusting brace.
e6f342c.jpg

Fig. 1: Exploded view of the water pump mounting

WARNING Do NOT use a prybar between the water pump housing and the engine block to separate the two components; this can cause scratches and/or gouges, which can prevent proper sealing.
  1. Pull the water pump off of the engine block. If the water pump is difficult to remove from the engine block, use a soft-faced mallet to tap the water pump housing until it loosens.
Do not disassemble the water pump; if the water pump is damaged or defective, the entire unit is replaced.
  1. Thoroughly clean the water pump gasket mating surfaces of old gasket material and corrosion.
To install:
  1. Along with a new gasket, install the water pump on the engine block. Tighten the water pump mounting bolts to 88-115 inch lbs. (10-13 Nm).
  2. On 1.3L and TFI 1.6L engines, install two new rubber seals: one between the water pump and oil pump, and the other between the water pump and the cylinder head. The MFI 1.6L engines only use one rubber seal, located between the water and oil pumps.
  1. If removed, install the alternator adjusting brace and the oil level dipstick retaining bolt.
  2. Install the timing belt, tensioner, plate, spring and cover.

Hope helps (remember comment and rated this).

Jul 19, 2010 | 1991 Geo Storm

1 Answer

Can you tell me where I can print instructions for free to help me change my timing belt in a 93 ford festiva


Here are the instructions for removing the timing cover, and for replacing the timing belt. If this is helpful, please click my accept button! Thanks!
Remove accessory drive belts.
  1. Remove water pump pulley to pump hub attaching bolts, then the pulley.
  2. Remove right inner fender panel to gain access to crankshaft pulley.
  3. Remove outer crankshaft pulley attaching bolts, then the outer stiffener/spacer and outer pulley
  4. Remove inner stiffener/spacer, attaching screws, inner pulley and baffle plate.
  5. Remove attaching bolts, then the upper and lower timing covers.
  6. Reverse procedure to install. When installing crankshaft pulley, ensure curved lip on baffle plate and deep recess of inner pulley face outward

8fb9fc4.gif
  1. Remove timing belt covers as outlined previously.
  2. Remove timing belt tensioner pulley attaching bolt, then the tensioner pulley, spring and spring cover
  3. If reusing old belt, mark direction of rotation on belt to aid installation.
  4. Remove timing belt from crankshaft and camshaft sprockets.
  5. Check crankshaft and camshaft sprockets, tensioner pulley and timing belt for wear or damage. Replace components as necessary.
  6. Align camshaft and crankshaft sprocket timing marks with marks on cylinder head and oil pump housing
  7. Install timing belt. If reusing old belt, ensure belt is installed so that direction of rotation mark made during removal is positioned correctly.
  8. Install spring and spring cover onto tensioner pulley, then install pulley and attaching bolt. Do not tighten bolt at this time.
  9. Install tensioner spring onto anchor, then tighten pulley attaching bolt to torque listed at the end of this section.
  10. Reinstall timing belt covers.

spacer.gif 2006-05-25_081817_fest2.thumb.gif
This photo shows timing marks.


59f76eb.gif

Jul 14, 2010 | 1993 Ford Festiva

1 Answer

Need to change surpentine belt on 1991 geo tracker. I have the belt but unsure how to go about changing


Loosen steering pump
loosen alternator bracket
change belt
belt tension should be 22 LB

Jun 26, 2010 | 1991 Geo Tracker

1 Answer

How do i replace a water pump on a 1993 geo


1 disconnect battery ground cable
2 drain cooling system
3 on models with a/c, proceed as follows:

a discharge a/c system
b loosen upper and lower compressor bolts and remove compressor drive belt
c remove a/c line from top of radiator shroud

4 remove water pump drive belt
5 remove reservoir tank from radiator bracket
6 remove radiator shroud and fan/clutch from vehicle
7 remove waterpump pulley from waterpump
8 remove timing tensioner and timing belt
9 remove dipstick tube
10 remove alternator mounting bracket at water pump
11 remove water pump mounting bolts and water pump
12 reverse procedure to install, using new gasket and rubber seal

Feb 18, 2010 | 1993 Geo Tracker

1 Answer

Changing the timing belt on a Hundai


  1. Remove all necessary components for access to the timing belt cover, then remove the cover.
  2. Rotate the crankshaft clockwise and align the timing marks so No. 1 piston will be at Top Dead Center (TDC) of the compression stroke.
  3. Loosen the tensioning bolt and the pivot bolt on the timing belt tensioner. Move the tensioner as far as it will go toward the water pump. Tighten the adjusting bolt.
  4. Mark the timing belt with an arrow showing direction of rotation.
  5. Remove the timing belt.
  6. If defective, remove the timing belt tensioner.
  7. Align the timing marks of the camshaft sprocket and check that the crankshaft timing marks are still in alignment.
  8. If removed, install the timing belt tensioner, spring and spacer with the bottom end of the spring free. Tighten the adjusting bolt slightly with the tensioner moved as far as possible away from the water pump.
  9. Install the free end of the spring into the locating tang on the front case.
  10. Position the timing belt over the crankshaft sprocket, then over the camshaft sprocket. Slip the back of the belt over the tensioner wheel.
  11. Turn the camshaft sprocket in the opposite of its normal direction of rotation until the straight side of the belt is tight and be sure the timing marks align.
    NOTE If the timing marks are not properly aligned, shift the belt 1 tooth at a time in the appropriate direction until they are aligned.
  12. Loosen the tensioner mounting bolts so the tensioner works, without the interference of any friction, under spring pressure. Be sure the belt follows the curve of the camshaft pulley so the teeth are engaged all the way around. Correct the path of the belt, if necessary.
  13. Tighten the tensioner adjusting bolt, then the tensioner pivot bolt to 15-18 ft. lbs. (20-26 Nm).
    NOTE Bolts must be tightened in the stated order or tension won't be correct.
  14. Turn the crankshaft 1 turn clockwise until timing marks again align to seat the belt.
  15. Loosen both tensioner attaching bolts and let the tensioner position itself under spring tension. Retighten the bolts.
  16. Check belt tension by putting a finger on the water pump side of the tensioner wheel and pull the belt toward the water pump. The belt should move toward the pump until the teeth are approximately 1 / 2 of the way across the head of the tensioner adjusting bolt. Re-tension the belt, if necessary.
  17. Install the timing belt covers and all other related components.

Feb 09, 2010 | Hyundai Motor 2004 Sonata

1 Answer

My 91 geo tracker has jumped time .how can i get it back in time?


remove Timing Belt covers set Top Dead center cyl one align cam mark and set tension

Dec 23, 2009 | 1991 Geo Tracker

1 Answer

Leak from the water pump


  • first of all you are probably going to need a torque wrench for the crank shaft pulley bolt it has 225lbs.of torque or more.I just did one on my 1991 honda accord dx .you have to take off a/c belt ,alternator etc. on the crank pulley.(I took it to a shop and they heated the 3/4 in. bolt and used torque wrench. I broke a half inch breaker bar trying to get it offf) next use puller to take off crankshaft pulley.support motor and remove motor mount bracket. take off upper and lower timing belt covers.take off timing belt and other belt using the tensioners.take off and replace water pump CHECK ALL TIMING MARKS with #1 piston@TDC. There are about 6.

Jun 02, 2009 | 1991 Honda Accord

2 Answers

Power steering


look thru the front hold of pS pulley
see bolt hole (missing bolt now)
replace this bolt and belt
then tension it.
then tighten this missing bolt.

done.
just like mine.
im doing a timing belt now.
this is an interference motor , you do too.

Apr 07, 2009 | 1993 Geo Tracker

Not finding what you are looking for?
1991 Geo Tracker Logo

Related Topics:

207 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...