Question about 1996 Chevrolet Blazer

1 Answer

The strater is making a noise it a new strater

The strater is making a noise it a new strater just put it on dose it need a chim

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,092 Answers

Yes, start with one, shims should have come with new starter.

Posted on Jul 09, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Strater remover

starter removal
1: pull battery NEG lug, (safe it off)
2: pull starter by , unbolting it, that includes the 2 wires, and 2 bolts.

reverse above, to put back.
or read the FSM.
or read here at (put that in the Google box.
or at mitchells.

pick one and read, its all there, all the time.

Nov 15, 2013 | 1996 Acura RL

1 Answer

How to turn change oil light

iI you mean 'how to turn change oil light off" go to fuse panel. Open drivers door there is a panel cover on the side of dash board, remove cover there is a red RESET button that resets oil pressure and tire pressure. Turn the ignition key to the on position but don't start the car. Now press and release the reset button the change oil light should start to flash, now press and hold the reset button until you hear chimming hold until chimming stops then release, the change oil light should go off. If you need to reset tire pressure press reset button twice, the first push will make the change oil light flash the second press will make the tire pressure light flash then hold untill chimming stops, light should go out . Hope this helps.

Sep 30, 2010 | 2000 Pontiac Grand Am GT

2 Answers

This car is new to me had work done on stearing last weak ? what kind of fluid dose it need for powerstearing I have heard it is not same as most cars it started making noise when turning after 200 miles...

no no no and not use brake fluid in the steering, this will eat away the seals and blow the system no way should brake fluid be used, you use auto transmission fluid or correct stearing fluid normally dexron2 but no brake fluid...hope this helps

Feb 15, 2010 | 1994 Toyota Camry

2 Answers

Kia sorento you non starter

bad connections at the starter, weak battery, bad solenoid and a bad strater will cause all the these conditions

Dec 13, 2009 | 2003 Kia Sorento

1 Answer

Car will not start lights and battery are good. Found freyed cable from battery (red)

i would first make sure the strater is getting voltage if its not you need to trace back and find out why that big red wire is probly the starter wire and if its freyed it neds replaced or a new end put on it. there is also another small wire connected to the starter you will need to put a meter on it and have someone turn the key to make sure the starter is also getting voltage signal fromthe ignition... ill check back in for replies leter on ...

Nov 09, 2009 | 2005 Chevrolet Malibu

1 Answer

1500 truck starter new flywheel new still makes a grinding noise also tried shimes still the same

You are moving the strater away from the flywheel when you put shims on it, this normally will make it worse. A clang will tel you its too close. When you got your starter shims did it come with a little piece of wire about the size in diamiter of a ink pen refill? if so that is the gauge for using the shims.You place it on the shaft of the starter, and it should just slide between the flywheel and the shaft. You may need to move the starter closer to the flywheel, this can be accomplished by only shiming the outside bolt on the starter- hope this helps.

Sep 04, 2009 | 1999 Chevrolet K1500

1 Answer

Chim when driving

Is the door ajar light on? Or is the fasten seatbelts light on? If the door is ajar light is on try removing the switch from the door pillar (start with drivers side first because it will have the most wear). Sometimes there's a rubber cover you pull back and they're usually held on with one or two screws, unhook the wire connector and check if the light went out. If it did buy a new or used replacement switch.

Feb 07, 2009 | 1998 Ford Windstar

2 Answers

Car will not crank. The battery is brand new and has a lot of fire. There is no noise when the key is turned on. The head lights do not come on. Help!

welcome to fixya

this sounds like the starter went on it remove the strater and take to a auto parts store and have them check it to see if it is bad

Aug 04, 2008 | 1991 Buick Park Avenue

1 Answer

1993 eagle medallion strater problems

Explain your meaning of:

won't turn over and start.
Can you hear the starter motor running but the engine is not physically cranking the engine as opposed to the engine actually starting up and running ?.

Or dose the starter just make a grinding noise and is not moving the engine ?

May 14, 2008 | 2000 Eagle Medallion

Not finding what you are looking for?
1996 Chevrolet Blazer Logo

Related Topics:

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides