Question about 1997 Ford Expedition

Open Question

The rear ac works good, but the front a//c does not blow out cold. how do you check the blender door? this is a 1997 expedition.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 142 Answers

SOURCE: a/c problem

You either have a bad control, or motor running the air direction door in the front HVAC unit, or a door that is stuck.

The front and rear units are totally separate.

The door directs where the air, cold or hot, should come out, whether it is panel vents, floor, defrost, or any combination of those.

This door and motor are located inside the heater box which usually requires a lot of the vehicle dash assembly to be taken apart to get to these parts.

Posted on Aug 28, 2008

alicantecoli
  • 22156 Answers

SOURCE: Ford Expedition 2002 Front Heater blows cold air below 45 MPH

impeller is made of plastic on teh water pump and its slipping and spinning on the shaft renew before weather warms up as engine will overheat

Posted on Jan 01, 2009

redbeard00
  • 957 Answers

SOURCE: have a 2000 ford expedition and the ac in the

Listen and see if the vent flap is moving from the hot position, to the cold position. If that's working then the evaporator may be clogged. It sits inside the same box that the heater core is inside of and if it becomes clogged with hair or dust, then it wont allow the blower to blow through it. But it would then bring hot air through the vents because the heater core is there too.

Posted on Jun 15, 2009

  • 634 Answers

SOURCE: Troubleshooting my blender value in my Dodge Ram

sounds like u guessed right blender door is getting stuck motor is weak or mount is cracked

Posted on Jul 07, 2009

  • 118 Answers

SOURCE: pasenger vents blow warm air while driver side blows cold when ac

Check and replace the right side temp-controller.

Posted on Jul 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My AC some times blows cool air with good pressure but most of the time blows air with low pressure. I have checked the AC pipe also. Its cool.


I'm wondering if it's NOT the AC but the blower fan, how does the heat side blow? if it's good on all blower settings then, it's more than likely your blender door is not opening and closing all the way. When the blender door stays open a little bit it'll let warmer outside air mix with the cold AC air causing it not to be as cold as it should.

Sep 19, 2015 | 2005 Toyota Corolla LE

1 Answer

My chevy tahoe ac front blow warm air and back blow cold air


check to see that the blender door accuator is working

Jul 08, 2015 | AC Cars & Trucks

1 Answer

Have a 2004 ford expedition, heat will blow out rear vents but blows cold air out the front.


you need to have automatic ac and heater control checked out at a garage problem could be in the mode switch or electrical problem causing front blend door actuator not working properly.your vechicle has the EATC SYSTEM which is computer control need diagnostie equipment to fix.

Dec 11, 2011 | 2004 Ford Expedition

1 Answer

My Air Condition is only blowing hot air in the front, but cold in the rear. Could anyone give me a start in correcting this problem? Thanks


possible blend door actuator faulty, or a faulty blend door. This door switches from hot to cold vents. On expeditions equipped with rear AC front and rear AC have seperate actuators. Hopefully this helps!!

Mar 31, 2010 | 2001 Ford Expedition

1 Answer

My 1997 jaguar xj6 blows air but no heat. Can anyone help? I checked all fuses, and AC works.


the only thing that can change the air from hot to cold, or vice versa is the blender door. under your dash is a box which has 2 compartments. one with your heater core which is hot and one with ac which is cold. the blender door basically diverts which on the air in your car is being drawn from. if it is cold, air is moving on the ac side. if its hot, air is moving through the heater core side. if its warm, the door is in the middle. your temperature control knob is conecteted to an actuator, which moves that door. the actuator is a motor, but if it goes out, the door will be stuck on whichever side it is on. i would check that first. hope this helps

Oct 20, 2009 | 2001 Jaguar XJ8

3 Answers

2004 Ford Expedition XLT, front blend door actuator


Hope I was avle to help, glad you up and going.

May 26, 2009 | 2004 Ford Expedition

Not finding what you are looking for?
1997 Ford Expedition Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...