Question about 2000 Chevrolet Tracker

1 Answer

I need an Idler pulley or the pulley that runs air conditioner belt as well as the belt for the power steering

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 6,826 Answers

OK.
If your idler pulley is bad then unbolt it and while you're at it replace the power steering belt.

REMOVAL & INSTALLATION Because serpentine belts use a spring loaded tensioner for adjustment, belt replacement tends to be somewhat easier than it used to be on engines where accessories were pivoted and bolted in place for tension adjustment. Basically, all belt replacement involves is to pivot the tensioner to loosen the belt, then slide the belt off of the pulleys. The two most important points are to pay CLOSE attention to the proper belt routing (since serpentine belts tend to be "snaked'' all different ways through the pulleys) and to make sure the V-ribs are properly seated in all the pulleys. Although belt routing diagrams have been included in this section, the first places you should check for proper belt routing are the labels in your engine compartment. These should include a belt routing diagram which may reflect changes made during a production run.

  1. Disconnect the negative battery cable for safety. This will help assure that no one mistakenly cranks the engine over with your hands between the pulleys, and that the cooling fan cannot activate while servicing the belt(s). NOTE: Take a good look at the installed belt and make a note of the routing. Before removing the belt, make sure the routing matches that of the belt routing label or one of the diagrams in this book. If for some reason a diagram does not match (you may not have the original engine or it may have been modified), carefully note the changes on a piece of paper.
  2. For tensioners equipped with a 1⁄2 in. (13mm) square hole, insert the drive end of a large breaker bar into the hole. Use the breaker bar to pivot the tensioner away from the drive belt. For tensioners not equipped with this hole, use the proper-sized socket and breaker bar (or a large handled wrench) on the tensioner idler pulley center bolt to pivot the tensioner away from the belt. This will loosen the belt sufficiently that it can be pulled off of one or more of the pulleys. It is usually easiest to carefully pull the belt out from underneath the tensioner pulley itself.
  3. Once the belt is off one of the pulleys, gently pivot the tensioner back into position. DO NOT allow the tensioner to snap back, as this could damage the tensioner's internal parts.
  4. Now finish removing the belt from the other pulleys and remove it from the engine. To install:
  5. While referring to the proper routing diagram (which you identified earlier), begin to route the belt over the pulleys, leaving whichever pulley you first released it from for last.
  6. Once the belt is mostly in place, carefully pivot the tensioner and position the belt over the final pulley. As you begin to allow the tensioner back into contact with the belt, run your hand around the pulleys and make sure the belt is properly seated in the ribs. If not, release the tension and seat the belt.
  7. Once the belt is installed, take another look at all the pulleys to double check your installation.
  8. Connect the negative battery cable, then start and run the engine to check belt operation.
  9. Once the engine has reached normal operating temperature, turn the ignition OFF and check that the belt tensioner arrow is within the proper adjustment range. Fig. 1: Often the underhood label will display the serpentine drive belt routing I need an Idler pulley or the pulley that runs air - 88231p43.gif
    Fig. 2: Relieve the belt tension by pivoting the automatic tensioner away from the belt, then remove the belt 88231p44.gif
    Fig. 3: Verifying serpentine belt alignment in the pulley 79244g60.gif
    Fig. 4: Fig. 1 Accessory V-belt routing — Tracker 1.6L engI need an Idler pulley or the pulley that runs air - 93024g03.gif 93024g03.gif
    Fig. 5: Fig. 2 AcceI need an Idler pulley or the pulley that runs air - 93024g04.gif routing — Tracker 1.6L engine with A/C and P/S 93024g04.gI need an Idler pulley or the pulley that runs air - 93024g05.gif_mi
    Fig. 6: Fig. 3 Accessory V-belt routing — Tracker 1.6L engine with P/S 93024g05.gif
prev.gif next.gif

Posted on Jul 09, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Serpentine belt keeps walking off 94 dodge caravan 3.0


for a belt to run off the pulleys , one of the pulleys will not be mounted parallel to all the other pulleys
check alternator pulley for alignment, power steering for alignment and tensioner pulleys for alignment
place a long straight edge across the faces of the pulleys to another pulley and see if it touches both side of the pulleys
check the idler pulley for failing bearings that will not allow that pulley to run in line under tension

Jan 20, 2017 | 1994 Dodge Caravan

2 Answers

What would cause my belt to not spib & squeal realy loud on my 93 Ford mercury topez


If the belt is not turning, there will be a seized pulley. Possible alternator.. power steering.... water pump... tensioner.... idler pulley ... AC compressor seized. The belt will need to be removed and all the pulleys spun by hand to isolate tone that may be seized

Mar 07, 2016 | Ford Cars & Trucks

1 Answer

I have 1996 Kia Sephia. When the air conditioner is on, the power steering doesn't work about half of the time and the car makes a squealing noise when turning, starting, and sometimes when idling....


Loose belt-tighten or worn idler pulley bearings.Tighten belts first and if the squeel is still there remove belt and check all pulley bearings.Grab the pulley by hand and give it a wriggle-there shouldn't be any play axially

Aug 10, 2011 | 1996 Kia Sephia

2 Answers

New serpentine belt smoking on 02 zx2


Check to make sure all the idler and other belt pulleys turn freely. It's possible that one of the pulley bearings is locked up which will cause the belt to smoke and fail as it slides over the siezed pulley.

Mar 07, 2011 | 2002 Ford ZX2

1 Answer

Which pulley is the idler pulley on a 2001 isuzu trooper 3.5L,DOHC motor?


stevenhurc_2.jpg 1=crank
2=alternator
3=idler tensioner
4=IDLER
5=fan idler
6=air cond compressor
7=accessory drive belt(serpentine belt)
8=power steering pump

just in case this is the timming belt and pulleys

stevenhurc_3.jpg

Jan 31, 2011 | 2001 Isuzu Trooper

1 Answer

HOW DO YOU CHANGE THE IDLER PULLEY?


It is as simple as removing the nut and pulling it off and sliding the new one on. Once you get it back replace the belt and set it to the correct tension. It is as simple as that. Without a belt tension gauge a good rule of thumb is about 1 inch of deflection at the longest belt run.
On your engine it's 1 inch between the power steering pump and the air conditioner compressor.

-->

May 20, 2010 | 1993 Jeep Grand Cherokee

2 Answers

Noise


it is not the steering pump because you are not moving the wheel it is the idler pulley it might need replacing check to see if the belt is in good condition if it is just use belt dressing on the pully to see if the sound goes away if it does then the idler pulley needs replacing

Oct 29, 2009 | 1999 Oldsmobile Cutlass

1 Answer

How to install drive belts to 1996 nissan quest


go here for help
http://autos.groups.yahoo.com/group/villagerquest/files/

392e46a.gif
Item Part Number Description 1 — A/C Compressor Drive Belt Idler Pulley Adjustment Bolt (If equipped)
(Part of 8678) 2 — A/C Compressor Drive Belt Idler Pulley Tensioner Bolt (If equipped)
(Part of 8678) 3 8678 A/C Compressor Drive Belt Idler Pulley (If equipped) 4 8620 A/C Compressor Drive Belt (If equipped) 5 2E884 A/C Clutch Pulley (If equipped) 6 10346 Generator 7 10344 Generator Pulley 8 11719 Generator Adjustment Bolt 9 — Generator Locking Bolt 10 8620 Generator Drive Belt 11 6312 Crankshaft Pulley 12 — Water Pump and Power Steering Pump Drive Belt Adjustment Bolt (Part of 8678) 13 8678 Water Pump and Power Steering Pump Drive Belt Idler Pulley 14 — Water Pump and Power Steering Pump Drive Belt Idler Pulley Locknut (Part of 8678) 15 3A733 Power Steering Pump Pulley 16 8620 Water Pump and Power Steering Pump Drive Belt 17 8509 Water Pump Pulley A — Tighten to 16-20 Nm (12-15 Lb-Ft) B — Tighten to 33-37 Nm (24-28 Lb-Ft)

Mar 28, 2009 | 1996 Nissan Quest

2 Answers

I need a diagram for a serpentine belt, for a 2000 ford taurus se


Starting at the crankshaft pulley, and going clockwise, the belt leaves the crank pulley,
Goes around the tensioner,
Goes around the water pump
Goes around the alternator
Goes around the upper idler
Goes around the Power Steering pump
Goes around the air conditioner pulley
then goes back to the Crank pulley


Sep 06, 2008 | 2000 Ford Taurus

Not finding what you are looking for?
2000 Chevrolet Tracker Logo

320 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75842 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...