Question about 1995 Dodge Neon

1 Answer

Do i have to remove the intake manifold to remove the starter? i cant seem to see the upper bolt.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 541 Answers

No, you should be able to remove it without that.

Posted on Jul 09, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the starter located on 1999 kia sportage? manual trans.?


you have to remove intake manifold bracket upper bolts.you have to remove clutch release cylinder move it aside.remove intake manifold bracket lower bolts remove bracket.then you can remove starter bolts and remove starter.

Nov 14, 2011 | Cars & Trucks

2 Answers

2003 Kia RIO WHEN TURNED TO ON CAR starts and the starter will not stop turning


Replace the starter.



Removal & Installation

1.5L & 1.6L (VIN 5) Engines

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative battery cable.
  3. Remove the 4 upper intake manifold stay bracket bolts.
  4. Disconnect the starter electrical connections.
  5. Remove the upper starter bolts.
  6. Remove the lower starter mounting bolt(s) and the starter.

    0996b43f80207fb6.jpg

    Fig. Starter mounting-1.5L and 1.6L engines


To install:
  1. Install the starter.
  2. Install the lower starter bolt and tighten to 27-38 ft. lbs. (37-52 Nm).
  3. Connect the starter electrical connections.
  4. Install the intake manifold support bracket and finger-tighten the 3 mounting bolts. Tighten the lower bolt to 27-38 ft. lbs. (37-52 Nm).
  5. Install the 4 upper intake manifold stay bracket bolts and tighten to 27-38 ft. lbs. (37-52 Nm).
  6. Install the upper starter bolts and tighten to 27-38 ft. lbs. (37-52 Nm).
  7. Connect the negative battery cable.

1.6L (VIN 3) Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:

    Negative battery cable Air intake assembly Shift cable and bracket Starter electrical connections Starter

To install:
  1. Install or connect the following:

    Starter Starter electrical connections Shift cable Air intake assembly Negative battery cable

May 04, 2011 | Kia Rio Cars & Trucks

1 Answer

Diagram on how to remove and install a spider fuel injector core on a 1994 chevy blazer s10


Here is the removal procedure, and the procedure is the same for both the V-6 and the V-8 Vortec engines. Also, be certain to put engine oil on the "o"-ring seal for the fuel injector assembly before installing the upper intake. Let me know if you require any further assistance.

REMOVAL:

1. Disconnect the battery negative cable assembly from the battery negative terminal.

2. Remove the air cleaner assembly.

3. Remove the wiring harness connectors and the brackets and move aside.

4. Remove the throttle cable and the bracket from the upper intake manifold.

5. Remove the cruise control cable, (if equipped).

6. Remove the fuel lines from the intake to the rear of the block.

7. Remove the ignition coil and the bracket.

8. Remove the upper intake manifold.

INSTALLATION:

1. Install the upper intake manifold gasket.

2. Install the upper intake manifold. Use care not to pinch the injector lines between the upper and lower intake manifolds.

3. Install the upper intake manifold bolts. Note the marks made at disassembly for proper stud location. Install the two corner studs first in order to help align the two halves. NOTE: Other than the two torque passes listed below, the OE Manufacturer did NOT address or supply a bolt tightening sequence for the upper Intake Manifold for this model year, or other model years where this 2 piece manifold setup is used. A "Play It Safe" final tightening sequence would be to tighten from the center most bolts to the outer most bolts.

4. Tighten the bolts in two steps: a. Tighten the bolts on the first sequence to 5 Nm (44 inch lbs.). b. Tighten the bolts on the final sequence to 10 Nm (88 inch lbs.).

5. Install the purge solenoid and bracket.

6. Install the ignition coil and bracket.

7. Install the PCV hose et the upper intake manifold.

8. Install the fuel lines from the intake at the rear of the block.

9. Install the cruise control cable (if equipped).

10. Install the throttle cable and bracket from the upper intake manifold.

11. Install the wiring harness connectors and brackets.

12. Install the air cleaner assembly.

13. Connect the battery negative cable assembly to the battery negative terminal. - Tighten the bolt to 15 Nm (11 ft. lbs.).


2640099.jpg

8a054ef.jpg

Oct 22, 2010 | Chevrolet Blazer Cars & Trucks

1 Answer

Change starter, how to get to, from under of from top what to take out first to get to the starter


TO REMOVE STARTER YOU HAVE TO REMOVE INTAKE MANIFOLD BRACKET UPPER BOLTS.REMOVE CLUTCH RELEASE CYLINDER AND MOVE IT ASIDE.REMOVE INTAKE MANIFOLD BRACKET LOWER BOLTS AND REMOVE BRACKET.REMOVE STARTER FROM TRANSMISSION.REMOVE STARTER ELECTRICAL WIRES.INSTALL NEW STARTER BACK VISA VERSA. TORQUE STARTER BOLTS 40 FT LBS TORQUE INTAKE BRACKET BOLTS 40 FT LBS.

Oct 08, 2010 | 1999 Kia Sportage

1 Answer

How do I change the starter?


Hi,

here is for the Removal & Installation
1. Disconnect negative battery cable. Remove two upper bolts from intake manifold bracket. Raise and support vehicle. Raise and support vehicle. On M/T, remove clutch slave cylinder from side of clutch housing and push it aside.
2. On all models remove lower intake manifold bracket bolts and bracket. Remove two upper starter bolts and a lower bolt. Pull starter from clutch (M/T)or converter (A/T) housing and prop in place. From above, disconnect starter solenoid "S" and "B" terminal connectors. From below, push transmission harness aside and remove starter.
3. To install, reverse removal proceedure. Rotate starter to provide proper clearance. Torque all nuts and bolts to specifications.


Good luck!

Aug 06, 2010 | 1999 Kia Sportage

2 Answers

Need to replace the intake manifold


3.8L Engine (most common) Upper Intake Manifold To Remove:
  1. Drain the cooling system.
  2. Remove or disconnect the following:
    • Negative battery cable.
    • Fuel injector sight shield.
    • Air cleaner intake duct.
    • Right spark plug wires from the ignition control module and reposition.
  3. Relieve the fuel pressure.
  4. Remove or disconnect the following:
    • Fuel rail assembly.
    • Brake booster hose from the vacuum source manifold in the upper intake manifold.
    • Exhaust Gas Recirculation Valve (EGR) wiring harness heat shield nut, bolt and the EGR heat shield.
    • Throttle body support bracket upper bolt.
  5. Disconnect the electrical connectors from the following:
    • EVAP purge solenoid
    • Throttle Position (T/P) sensor
    • Idle Air Control (IAC) valve
    • Manifold Absolute Pressure (MAP) sensor
    • Mass Air Flow (MAF) sensor
    • EVAP purge solenoid vacuum line from the throttle body.
    • Accelerator and the cruise control cables with the bracket from the throttle body.
  6. Remove or disconnect the following:
    • Upper intake manifold bolts and stud.
    • Clean the upper intake manifold bolt threads.
  7. Remove or disconnect the following:
    • Upper intake manifold by lifting the back of the intake and sliding the manifold forward from the throttle body support bracket.
    • Upper-to-lower intake manifold carrier gasket from the upper intake manifold.
  8. If the upper intake manifold is being replaced, remove the following:
    • Throttle body assembly.
    • Manifold Absolute Pressure (MAP) sensor.
    • Positive Crankcase Ventilation (PCV) valve.
    • Vacuum source manifold.
Upper intake manifold bolt torque sequence (3.8L engine) gm-03-38-530.gif

To Install:
  1. If the manifold was replaced, install or connect the following:
    • Vacuum source manifold.
    • Positive Crankcase Ventilation (PCV) valve.
    • Manifold Absolute Pressure (MAP) sensor.
    • Throttle body assembly.
    • Upper-to-lower intake manifold carrier gasket to the upper intake manifold.
  2. Carefully place the upper intake manifold onto the lower intake manifold. Ensure that the alignment pins in the upper intake manifold align with the holes in the lower intake manifold. NOTE: Apply thread lock compound, to the bolt threads before assembly.
  3. Install or connect the following:
    • Upper intake manifold. Tighten the upper intake manifold bolts in sequence to 89 in lbs (10 Nm)
    • Accelerator and the cruise control cables with the bracket to the throttle body.
    • EVAP purge solenoid vacuum line to the throttle body.
  4. Connect the electrical connectors to the following:
    • Mass Air Flow (MAF) sensor
    • Manifold Absolute Pressure (MAP) sensor
    • Idle Air Control (IAC) valve
    • Throttle Position (T/P) sensor
    • EVAP purge solenoid
  5. Install or connect the following:
    • Throttle body upper support bracket bolt. Tighten the bolt to 89 in lbs (10 Nm)
    • EGR valve wiring harness heat shield, nut and the bolt. Tighten the nut and the bolt to 89 in lbs (10 Nm)
    • Brake booster hose to the vacuum source manifold.
    • Fuel rail assembly.
    • Right spark plug wires.
    • Air cleaner intake duct.
    • Fuel injector sight shield.
  6. Connect the negative battery cable.
  7. Fill the cooling system.
  8. Inspect for fluid or vacuum leaks.
Lower Intake Manifold (W/O Supercharger) To Remove:
  1. Remove or disconnect the following:
    • Upper intake manifold.
    • Generator brace.
    • Drive belt tensioner with the mounting bracket and the heater water bypass inlet pipe.
    • Exhaust gas recirculation EGR outlet pipe bolt from the lower intake manifold.
    • Radiator inlet hose from the water outlet housing.
    • ECT sensor electrical connector.
    • Right upper engine mount strut bracket.
    • Generator brace bracket bolts.
    • Generator brace bracket.
    • Lower intake manifold bolts.
    • Lower intake manifold.
    • Lower intake manifold seals.
    • Lower intake manifold gaskets.
  2. If replacing the lower intake manifold, Remove or disconnect:
    • Water outlet housing bolt and stud
    • Water outlet housing
    • Gasket and the thermostat.
    • ECT sensor.
  3. Inspect the flatness of inlet flanges.
  4. Clean the intake manifold mating surfaces.
  5. Clean the intake manifold bolts and bolt holes of adhesive compound.
To Install:
  1. If removed, install the ECT sensor.
    • Tighten the ECT sensor to 18 ft. lbs. (25 Nm)
  2. If removed, install the thermostat, the gasket, and the water outlet housing.
  3. If removed, install the water outlet housing bolt and the stud.
    • Tighten the bolt and stud to 20 ft. lbs. (27 Nm)
  4. Install or connect the following:
    • Lower intake manifold gaskets. NOTE: Apply sealer GM P/N 12346286 (Canadian P/N 10953472) or equivalent to the ends of the intake manifold seals.
    • Lower intake manifold seals.
    • Lower intake manifold.
    • Lower intake manifold bolts.
    NOTE: Apply thread lock compound GM P/N 12345382 (Canadian P/N 10953489) or equivalent to the two hidden bolts and ensure they are installed.
  5. Tighten the lower intake manifold bolts in sequence to 11 ft. lbs. (15 Nm) gmpc_v6_5.gif

  6. Install or connect the following:
    • Generator brace bracket.
    • Generator brace bracket bolts. Tighten the bolts to 37 ft. lbs. (50 Nm)
    • Right upper engine mount strut bracket.
    • ECT sensor electrical connector.
    • Radiator inlet hose to the water outlet housing.
    • EGR outlet pipe to the lower intake manifold.
    • EGR outlet pipe bolt to the lower intake manifold. Tighten the bolt to 21 ft. lbs. (29 Nm)
    • Drive belt tensioner.
    • Generator brace.
    • Upper intake manifold.
  7. Inspect for leaks.
Lower Intake Manifold (W/ Supercharger) To Remove:
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the supercharger.
  4. Remove the thermostat housing.
  5. Remove the EGR pipe at the intake manifold.
  6. Disconnect the electrical connection at the temperature sensor.
  7. Remove the intake manifold and gaskets.
NOTE: The coolant bypass tube will release from the intake manifold when the manifold is removed.
To Install:
  1. Clean the gasket sealing surfaces.
  2. Install the intake manifold gaskets.
  3. Align the coolant bypass tube with the opening in the intake manifold and install the manifold. Tighten the bolts to 11 lb ft (15 Nm).
  4. Install the electrical connector to the temperature sensor.
  5. Install the EGR pipe to the intake manifold.
  6. Install the thermostat housing.
  7. Install the supercharger.
  8. Fill the cooling system.
  9. Connect the negative battery cable.

Aug 05, 2010 | 1997 Pontiac Grand Prix

1 Answer

Intake manifold gasket / replace


3.8L Engine

NOTE The 3.8L (VIN K) non-supercharged engine uses a two-piece intake manifold consisting of an upper air plenum which mounts the throttle body and a lower intake manifold assembly which houses the fuel injectors. The 3.8L (VIN 1) supercharged engine uses a similar lower intake manifold. The supercharger serves as the upper manifold.
Lower Manifold

NOTE Two bolts which fasten the lower intake manifold to the cylinder head are accessible only after the upper intake manifold is removed. These bolts are located in the right front and left rear corners of the lower intake manifold. Remove the upper intake manifold to service the lower intake.
The 3.8L (VIN 1) supercharged engine uses a manifold similar to the 3.8L (VIN K), but the supercharger serves as the upper manifold.
  1. Disconnect the negative battery cable.
  2. On 3.8L (VIN 1) engines, remove the supercharger assembly. Please see the procedure in this section.
  3. Remove the upper intake manifold using the procedure above.
  4. Remove the EGR outlet pipe from the intake manifold.
  5. Detach the engine coolant temperature sensor wiring harness from the sensor.
  6. Remove the lower intake manifold bolts and carefully lift off the manifold.

To install:


0900c15280269f1b.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Lower intake manifold bolt torque sequence-3.8L (VIN K) engine
  1. Clean all parts well with degreaser, especially the gasket seal surfaces on the upper and lower manifold pieces and between the lower manifold and the cylinder heads..
  2. Install new gaskets to the cylinder heads and new seals to the engine block. Carefully lower the manifold into place. Apply thread-locking compound to the bolt threads. Make sure to install the two hidden bolts in the lower intake manifold. Hand start all bolts, then torque evenly to 11 ft. lbs. (15 Nm). Follow the toque sequence, starting in the center, then working outwards in a circle.
  3. Install the remaining components in the reverse order of the removal process.

Upper Intake Manifold (Plenum)
  1. Disconnect the negative battery cable.
  2. On 3.8L (VIN 1) engines, remove the supercharger assembly. Please see the procedure in this section.
  3. Tag for identification, then remove the right side spark plug wires.
  4. Disconnect the ignition wires from the fuel rail.
  5. Remove the fuel rail. Please see Section 5.
  6. Remove the cable bracket from the intake manifold.
  7. Remove the throttle body.


NOTE Two bolts which fasten the lower intake manifold to the cylinder head are accessible are accessible only after the upper intake manifold is removed. These bolts are located in the right front and left rear corners of the lower intake manifold.
  1. Remove the upper intake manifold bolts and carefully lift the upper intake manifold from the engine.



0900c15280269f1c.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Upper intake manifold and bolt torque sequence-3.8L (VIN K) engine
To install:
  1. Clean all parts well with degreaser, especially the gasket seal surfaces on the upper and lower manifold pieces.
  2. Install new gaskets to the cylinder heads and new seals to the engine block. Carefully lower the manifold into place. Make sure to install the two hidden bolts in the lower intake manifold. Hand start all bolts, then torque evenly to 89 inch lbs. (10 Nm). Follow the torque sequence, starting in the center, then working outwards in a circle.
  3. Install the remaining components in the reverse order of the removal process.

Sep 11, 2009 | 1999 Buick Regal

1 Answer

Replace starter


96 probe, 2.0L 4 cylinder. Should be similar to 626 I think.

Starter Motor
Removal


Exploded View of the Starter Motor Mounting Components




  1. stu~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: When servicing the starter motor or performing other underhood work in the vicinity of the starter motor (11002), be aware that the heavy gauge battery input lead at the starter solenoid is "electrically hot" at all times. A protective cap or boot is provided over this terminal (B-terminal) on all carlines and must be replaced after servicing. Be sure to disconnect the battery ground cable before servicing the starter motor.
    Disconnect the battery ground cable (14301).
  1. Remove the air cleaner (ACL) and the air cleaner to intake manifold tube (9B697). Refer to Section 03-12A for the procedures.
  1. Remove the two upper starter motor bolts.




  1. Raise and support the vehicle.
  1. Remove the intake manifold support bolts and the intake manifold support (9J444).




  1. Disconnect the S-terminal wire.
  1. Remove the B-terminal wire nut and disconnect the B-terminal wire.
  1. Remove the lower starter motor bolt.
  1. Remove the starter motor.

Aug 10, 2009 | 1995 Mazda 626

1 Answer

Starter for kia sportage 2000


  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable Intake manifold bracket upper bolts Clutch release cylinder and move it aside, if equipped Intake manifold bracket lower bolts and remove the bracket Starter from the clutch, manual transmissions only Starter from the torque converter, automatic transmissions only Starter electrical connectors Move the transmission wire harness aside Starter


    0900c152801b0603.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Exploded view of the starter

To install:
  1. Install or connect the following:

    Starter to the engine well Starter electrical connectors Lower intake manifold bracket and install the upper bolts Starter into position. When aligned properly torque the bolts to 40 ft. lbs. (54 Nm). Torque the intake manifold bracket bolts to 40 ft. lbs. (54 Nm). Properly position the clutch release cylinder, if equipped. Torque the bolts to 40 ft. lbs. (54 Nm). Torque the intake manifold bracket upper bolts to 40 ft. lbs. (54 Nm). Negative battery cable

Jun 28, 2009 | 2000 Kia Sportage

2 Answers

1998 kia sephia starter


Its located just under the intake manifold. you will need to remove the exhaust pipe to access it. there is also an upper and lower intake manifold support bracket that will need to be removed as well to extract the starter.

Its in a tough spot.

Jun 17, 2009 | 1998 Kia Sephia

Not finding what you are looking for?
1995 Dodge Neon Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...