Question about 2006 Ford Freestar

Open Question

How to remove second row seat in freestar - 2006 Ford Freestar

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: removing the 2nd and 3rd row seats

3rd row, you simply pull the lever which makes the back fold down and then grip the handle located on the bottom and pull toward you slightly hard. They are heavy so it seems like they aren't coming out, just pull hard. second row, you flip all the way up and push with them standing up and they come unhooked. Good Luck! I didn't have any problems, except they are at least 50+lbs!

Posted on Jan 07, 2009

  • 41 Answers

SOURCE: Remove seat from second row in Honda Mini Van 2007

on the passenger side feel under the seat and there is a lever that pulls toward you as you stand at the sliding door.

First, raise the armrest, then lower the back all the way forward. Then remove the headrest sit it out of the way and while pulling the lever under the seat towards you, lift up the seat from the back so it tilts forward. When it is standing on its "nose" lift first one side shifting it either forward or backwards to clear the rod on which it is hooked. Do the same with the other side of the seat and then lift it out. Installation is the reverse of removal.

The other seat is much the same, though sometimes the lever is a little different but in the same place.

Good luck,
bob

Posted on Jun 09, 2009

  • 6 Answers

SOURCE: How can I remove front row seat headrest?

Most volvo headrest can be removed by releasing the catches which are on the back of the headrest on some models and on the front on others I believe on 960 they are on the back. To release the seat on a 960 look where the shafts should be then follow it down on the back where the seat back top stops then goes in press around that area you should be able to find the catch there pull up on the headrest while releasing the catch you have to do this on both sides. The headrest should come off this also works on 740 and 760 series the volvo 780 is a different story the only way to get the headrest off on that is to disassemble the seat

Posted on Mar 14, 2009

MNfisherman
  • 11896 Answers

SOURCE: need instructions to remove second and third row seats

On the bottom of the seats, there is a handle on each side. Lift up both handles at same time and have someone else lift up and pull out the back bottom of the seat and it will pull out.

Posted on Aug 24, 2009

  • 1 Answer

SOURCE: How do I remove the third row seat. lever wont budge

I just fixed my dad's 04 suburban with the back seat's #1 lever not budging. It's a surprisingly simple fix: take a 5 inch flat head screw driver and as you look into the slot where the #1 handle goes, you will see a wheel mechanism that it is connected too. to the left of that wheel, you will see a hammer mechanism with a cord attached to it. all you have to do is carefully push the lever with the screw driver while gently lifting up on the handle.
Hope this helps!

Posted on May 21, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I convert 2nd row captains chairs with either a jump seat in the middle, or switch to a bench?


Contact the service manager at your local Ford dealership; he or the senior master mechanic should be able to help.

Mar 24, 2015 | 2004 Ford Freestar SEL

1 Answer

How to remove 3rd row seat


If your Freestar is similar to earlier Windstars, third row seat removal is approached from the rear with the tailgate open. There are two latches at the bottom that pull up to release the seat from its locked position. You tilt the seat forward and pull up then pull the seat back toward you to release.

Dec 13, 2014 | 2006 Ford Freestyle

1 Answer

How do I remove second row seat


If its on rails, pull the handle and slide it off. If no rails pull really hard from the top or kick from the back. Check for bolts behind and underneath the carpet, it may have a couple fasteners. You can really beat on a seat and it will take it. Sometimes that's what you gotta do.

Nov 17, 2014 | 2005 Mitsubishi Montero

1 Answer

How do I remove second row seat?


What type of vehicle are we talking about?

Nov 17, 2014 | 2005 Mitsubishi Montero

1 Answer

I have a 2001 chrysler voyager where is the blend door actuator located and how to remove it


its in the HVAC heater core box,
how to remove it is a very long answer.
read the FSM on HVAC
or login to alldata.com see HVAC chapter, and read. it.
anyone can, not just me.

i see this on line,.
  1. Disconnect and isolate the battery negative cable.
  2. Remove first row seat.
  3. Remove second row seat.
  4. Remove sliding door sill trim panel.
  5. Remove quarter trim bolster.
  6. Remove D-pillar trim panel.
  7. Remove first row seat belt anchor.
  8. Remove second row seat belt anchor.
  9. Remove screws attaching quarter trim to quarter panel from bolster area.
  10. Remove screws attaching rear edge of quarter trim to attaching bracket.
  11. Disengage hidden clips attaching front of quarter trim to quarter panel rearward of sliding door opening and at locators.
  12. Remove quarter trim from quarter panel.
  13. Disconnect speaker wire connector on LWB quarter trim panel with rear air conditioning.
  14. Pass second row seat belt through slot in trim panel on long wheel base vehicle.
  15. Pass first row seat belt through slot in trim panel.
  16. Remove quarter trim panel from vehicle.
  17. Remove the two screws that secure the top of the quarter trim panel attaching bracket to the quarter inner panel.
  18. Remove the screw that secures the back of the rear heater-A/C unit housing to the right D-pillar.
  19. Remove the screw that secures the front of the rear heater-A/C unit housing to the right quarter inner panel.
  20. Carefully pull the top of the rear heater-A/C unit housing away from the right quarter inner panel far enough to reach between the rear heater-A/C unit housing and the quarter inner panel to access the blend door actuator.
  21. Remove the two screws that secure the blend door actuator to the rear heater-A/C unit housing.
  22. Pull the blend door actuator away from the rear heater-A/C unit housing far enough to disengage the actuator output shaft from the blend air door pivot.
  23. Raise the blend door actuator far enough to access and disconnect the rear HVAC wire harness connector for the actuator from the actuator connector receptacle.
  24. Remove the blend door actuator from between the rear heater-A/C unit housing and the quarter inner panel.

May 21, 2014 | 2001 Chrysler Voyager

1 Answer

2nd row seat of my ford excursion seat went down but I can't get it to release and return to an upright position


cabling inside the seat is faulty ,,,,, nasty problem as you have to remove upholstery to repair it ,,,,,

Dec 06, 2013 | 2002 Ford Excursion

1 Answer

Need to remove 2nd row seats in a ford freestar


Adjust the seat so it's folded and upright. Near where the seat is attached to the floor is a "square shaped" metal bar (attack from the bak of the seat). Pull that bar to release the floor clamp. Note I had to lean the chair to about 45 degrees to get it to work. It took a fair amount of pulling and cursing. Now that it's out, I'm going to spray the clamp with a little WD40. Maybe next time it'll work more smoothly.

Aug 22, 2010 | 2006 Ford Freestar

2 Answers

I want to make my 1999 Mercury Villager Sport into a cargo loader, with just the front seats kept and the rest of the back empty. How do I remove the other 3 seats? So far, I can't get any of them to budge...


the middle seats come out easily. There are 2 handles you have to lift up on each of the bucket seats, they are in the front of the seat down by the seat tracks. After you lift them, tilt the seat upward in the front and rotate them backward. Then lift out of the hooks. Each seat is held down by 4 hoks.

The 3rd row seat is not designed to come out xcept by a technician. It does slide forward all the way up to the front seat. It has a sliding seat track.
First, lift the T handle under the seat cushion on the left front side of the seat. This will allow you to lift the seat bottom up all the way to lcok in the full up position.
Then, lift the lever on the same side of the seat and slide the seat forward. It will stop in 4 places.
Rear -Rear
6 inches forward of that.
another two ft to the second row seating position
full frward against the front seats.

Pleae rate as fixya if this helps.

c4253aa.gif Seat —Third Row Bench Removal
sxv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Removal of the third row bench seat requires more than one technician.
  1. Remove the second row seats. For additional information, refer to Seat—Second Row .
  1. Remove the floor mats.
  1. Lock the seat cushion in the upright position.
    1. Lift the handle to release the cushion.
    1. Lock the seat cushion in the upright position.
0235766.gif
  1. Move the third row bench seat to the second row position.
    • Lift the seat track release handle.
  1. Remove the two bolt covers.
  1. Remove the two seat track front bolts.
  1. Remove the four seat track rear bolts.
    1. Position the rear seat cushion floor cover aside.
    1. Remove the four seat track rear bolts.
  1. Remove the third row bench seat.

Mar 02, 2009 | 1997 Mercury Villager

1 Answer

Removing the 2nd and 3rd row seats


3rd row, you simply pull the lever which makes the back fold down and then grip the handle located on the bottom and pull toward you slightly hard. They are heavy so it seems like they aren't coming out, just pull hard. second row, you flip all the way up and push with them standing up and they come unhooked. Good Luck! I didn't have any problems, except they are at least 50+lbs!

Nov 18, 2008 | 2007 GMC Yukon

Not finding what you are looking for?
2006 Ford Freestar Logo

Related Topics:

542 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...