Question about Ford Mustang

2 Answers

Need to replace white o ring on the power steering hose for a 1997 mustang but how do i remove the hose from the threading

Posted by on

  • leijaavel Jul 09, 2010

    i bought a white o ring replacement for the power steering hose on my 1997 mustang but can not release it from the threaded part how can i do that

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,826 Answers

You can not,it must be replaced as a whole unit.

Posted on Jul 09, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,865 Answers

Hello. You can not separate these. You will have to replace the hose. J.

Posted on Jul 09, 2010

  • leijaavel Jul 09, 2010

    they sell u the o ring replacement and they said it should pop out

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to take off rak in pinon on 98 cadillac


Hey Irma.. here is a video.. this is not an easy thing to do... you need to be very mechanically inclined and experienced.. you have outer tie rods, X2, (steering system) that have to be disconnected.. the intermediate shaft has to be disconnected and collapsed... the power steering hoses have to be removed and sealed (put a baggie around them and tape into place - keep dirt out of threads and doesn't contaminate the o-rings or hose ends...be careful with those o-rings, they are not "just regular o-rings.. you will need to refill the power steering fluid reservoir after you reinstall everything and start the engine..(PUT some fluid in first!! - so you don't have a dry gear!).. Do you have the tools necessary.. 2 sets of jack stands, - DO NOT attempt this without them.. NEVER trust a jack!!!

Rack Pinion Steering Replacement Cadillac Deville 1997

Jun 19, 2017 | Cadillac Cars & Trucks

1 Answer

Need to replace power steering hose on 1997 Jeep Grand Cherokee


Unscrew hose on both ends. Remove hose. Reverse procedure to install. Fill and bleed power steering system.

May 04, 2012 | 1997 Jeep Grand Cherokee

1 Answer

Replace pressure house on 1985 mustang


For procedure to replace power steering hoses,click the link below :----http://technoanswers.blogspot.in/2012/02/how-to-replace-power-steering-pressure.html
----------Also its advisable to go through this additional help links.Click the link to go through the procedures:----How to Remove Power steering Pressure Hose?

http://schematicsdiagram.blogspot.com/2011/12/how-to-remove-power-steering-pressure.html


Vacuum hose Routing diagram?

http://repairhelpcenter.blogspot.com/2011/11/vacuum-hose-routing-diagram-for-acura.html


Ac line and evaporator drain hose?

http://repairhelpcenter.blogspot.com/2011/10/ac-line-and-evaporator-drain-hose-on.html


How to disconnect the hose form the Evap Canister?

http://schematicsdiagram.blogspot.com/2011/12/how-to-disconnect-hose-form-evap.html


Vacuum Hose Routing Diagram For Throttle Body?

http://schematicsdiagram.blogspot.com/2011/12/vacuum-hose-routing-diagram-for-1995.html


How exactly the Vehicles A/C Hose works?

http://repairhelpcenter.blogspot.com/2011/11/how-exactly-vehicles-ac-hose-works.html


HOW TO REPLACE AN UPPER RADIATOR HOSE

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-upper-radiator-hose.html
HOW TO REPLACE A LOWER RADIATOR HOSE

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-lower-radiator-hose.html



Fail smog test due to gas filter hose?

http://repairhelpcenter.blogspot.com/2012/01/fail-smog-test-due-to-gas-filter-hose.html


EGR Hoses melting?

http://repairhelpcenter.blogspot.com/2011/12/egr-hoses-melting.html


EVAP connecting hose to PCV valve Collapse?

http://schematicsdiagram.blogspot.com/2012/01/evap-connecting-hose-to-pcv-valve.html


--------How to replace Power steering rack and pinion gear? http://technoanswers.blogspot.in/2012/02/how-to-replace-power-steering-rack-and.html
--------How to replace Power Steering Pump?

Also bleeding:

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-power-steering-pump-on.html

----------------
How to replace Steering Linkage? http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-steering-linkage-on.html
-----Car steering wheel makes noise?

http://schematicsdiagram.blogspot.com/2011/12/car-steering-wheel-makes-noise.html

------
Car makes clicking or tapping sound? http://schematicsdiagram.blogspot.com/2011/12/car-makes-clicking-or-tapping-sound.html
---------This will help.Thanks.

Feb 16, 2012 | 1985 Ford Mustang

1 Answer

HOW DO I REPLACE THE HIGH PRESSURE LINE FOR A POWER STEERING UNIT ON A 1998 MUSTANG?


Disconnect battery ground cable.
Remove engine Air Cleaner (ACL) .
Disconnect electrical connector in back of engine cooling fan motor.
Remove radiator fan shroud.
Disconnect constant control relay module harness from headlamp harness and place constant control relay module on top of engine to provide accessibility to power steering lines.
Remove wiring harness guide retaining screws and position guide aside.
Remove screw at power steering hose bracket.
Remove anti-rattle clip.
Remove plastic strap retaining tubes to power rack and pinion steering gear.
Remove power steering pressure hose at power steering pump.
Remove power steering pressure hose at power rack and pinion steering gear.
Remove power steering pressure hose from vehicle.
Reverse procedure to install new hose.
Fill and bleed power steering system.

Aug 20, 2011 | Ford Mustang Cars & Trucks

1 Answer

After removing the snap ring and the nut below it on the steering column; what do I remove next in order to get the turn signal switch replaced?


you need a steering column lock plate compressor it threads onto the shaft and pushes the lock plate in compressing the spring and allows you room to remove the lock ring around the steering column shaft then you remove the tool , ring , lock plate , then you can see the turn signal switch sometimes you can push the plate in with your left hand and pry the lock ring out with the right hand

Aug 28, 2010 | 1997 GMC Sonoma

1 Answer

Replace power steering pump.


  1. Disconnect the negative battery cable.
  2. If necessary, remove the air cleaner duct and the air cleaner.
  3. Remove the drive belt from the air conditioning compressor, if equipped.
  4. Loosen power steering pump belt adjustment as follows:
    1. Loosen the pivot and mounting bolts.
    2. Loosen the idler pulley locknut and turn the adjusting nut counterclockwise to remove the power steering belt.
  5. Loosen the power steering hoses at the pump and remove the bolts holding the power steering pump to the bracket.
  6. Disconnect and plug the power steering hoses and remove the pump from the vehicle.
To install:
  1. Using new O-rings, connect the power steering hoses to the steering pump.
  2. Install the power steering pump and secure it with its mounting bolts. Tighten the front and rear mounting bolts to specifications.
  3. Install the remaining components in the reverse order from which they were removed.
  4. Connect the negative battery cable.
  5. Fill the power steering system, start the engine and turn the steering wheel from side-to-side to bleed air from system

Feb 14, 2010 | 1997 Nissan Maxima

1 Answer

How to r&r powersteering pump 1998 mercury grand marquis


Hopfully this will be ALL you need Besides Pulley REMOVAL TOOL It can be Rented @ AutoZONE

REMOVAL
  1. Remove drive belt.
  2. Raise vehicle on hoist. WARNING: TURN AIR SUSPENSION SWITCH (LOCATED IN LUGGAGE COMPARTMENT) OFF TO PREVENT VEHICLE DAMAGE OR PERSONAL INJURY.
  3. Remove power steering pressure hose bracket.
  4. Disconnect electrical connector at power steering control valve actuator.
    1. Install Steering Pump Pulley Remover T69L-10300-B on the pulley hub. CAUTION: Do not apply in-and-out pressure on the power steering pump shaft. Pressure will damage the internal thrust areas.
    2. Hold the small hex-head and rotate the tool nut counterclockwise to remove the power steering pump pulley.
    3. Disconnect power steering pressure hose at power steering pump and drain fluid into a container.
    4. Disconnect power steering return hose at power steering pump and drain fluid into a container.
    5. Remove four retaining bolts and power steering pump and power steering pump pulley assembly.
    6. Remove power steering pressure switch from pump.
    INSTALLATION
    1. Position the power steering pump on the mounting bosses of engine block and install the bolts at the side of the power steering pump. Tighten to 20-30 Nm (15-22 ft. lbs.).
    2. Connect the power steering reservoir pump hose to the power steering pump and reposition the hose clamp to power steering pump inlet fitting.
    3. Replace power steering pressure hose O-ring.
    4. Install the power steering pressure hose to the power steering pump fitting. Tighten the tube nut with a tube nut wrench rather than with an open-end wrench. Tighten to 34-46 Nm (26-33 ft. lbs.). NOTE: Swivel or end play of the power steering pressure hose end is normal and does not indicate a loose fitting.
    5. Place the power steering pump pulley on the power steering pump shaft and install Power Steering Pump Pulley Replacer T91P-3A733-A. The small diameter threads on the tool should be engaged in the power steering pump shaft. CAUTION: Do not apply in and out pressure on the shaft. Pressure will damage the internal rotating group.
    6. Hold the small hex-head and rotate the tool nut clockwise to install the power steering pump pulley on the shaft. CAUTION: Do not apply in and out pressure on the shaft. Pressure will damage the internal rotating group. NOTE: The power steering pump pulley face must be flush within 0.25 mm (0.010 inch) of the end of the pump shaft.
    7. Remove the Power Steering Pump Pulley Replacer T91P-3A733-A.
    8. Remove the shipping tube nut from power steering pump housing prior to installation.
    9. Connect electrical connector to power steering control valve actuator.
    1. Install power steering pressure hose bracket.
    1. Lower the vehicle.
    2. If equipped, turn the air suspension ON.
    3. Install drive belt on the power steering pump pulley.
    4. Fill the power steering pump reservoir with Power Steering Fluid Motorcraft MERCON(r) ATF.

Oct 04, 2009 | 1998 Mercury Grand Marquis

1 Answer

HOW DO YOU TAKE OFF A POWER STEERING LINE? I HAVE A 96 FORD E150 5.8


When power steering hose replacement is required, follow these steps:
  1. With the engine stopped, remove the return hose at the power steering gear, and allow the fluid to drain from this hose into a drain pan. On some cars, the vehicle must be lifted on a hoist to replace the power steering hoses.
  2. Loosen and remove all hose fittings from the pump and steering gear.
  3. Remove all hose-to-chassis clips.
  4. Remove the hoses from the chassis, and cap the pump and steering fittings.
  5. If O-rings are used on the hose ends, install new O-rings. TRW steering gear cylinder lines have gaskets that are serviced as a unit. The old gasket must be pried out of the fittings in the housing before the new lines and gaskets are installed. Lubricate O-rings with power steering fluid.
  6. Reverse steps 1 through 4 to install the power steering hoses. Tighten all fittings to the manufacturer's specified torque. Be sure all hose-to-chassis clips are in place. Do not position hoses where they rub on other components.
  7. Fill the pump reservoir to the full mark with the manufacturer's recommended fluid. Bleed air from the power steering system. Check the fluid level in the reservoir and add fluid as required.

Jul 07, 2009 | 1996 Ford Econoline

1 Answer

Replacing Power hi-pressure Steering Hose 99 Dodge Durango


When you remove the oil steering hose, just do a match fit. Match the oil hose with the new one and pre oil the O rings before you connect the fittings. Don't for get to clean all the power steering fluid before you go for a test drive, power steering fluid is flammable. Good luck and hope this helps. Keep me posted friend. 

Jul 03, 2009 | 1997 Chevrolet Lumina

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...