Question about 2000 Ford Expedition

1 Answer

How do I access left rear turn signal to replace bulb

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Need to replace turn signal bulb. How to access? pulled out piece of foam out of approx. 2" hole that feed wires go thru...............

Posted on Jul 09, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace left rear brake light bulb


1) Open trunk
2) Remove small round plastic access panel with a flat tip screw driver by prying open
3) Remove flat tip screw holding tail light assembly
4) Remove tail light assembly by pulling outward, careful not to break plastic guide/nub
5) Disconnect wiring connectors
6) Remove plastic housing access plate on back of tail light assembly by twisting/turning tabs until they click and then lift access plate from tail light assembly
7) When viewing the the bulbs, the turn signal bulb is the bottom left bulb
8) Install in reverse order, ensuring tail light seal seats properly during installation

Oct 13, 2014 | 1999 Audi A4

1 Answer

How to replace rear turn signal bulb 99 park avenue


Replacing a front turn signal bulb is easy, as I just did my own. On the front driver's side, look at the wheel well splash panel and you'll see one plastic pin. Use a claw hammer and pull the pin out. Now just pull the plastic splash panel out of your way.

Look behind the front bumper and you'll see the light fixture. The top left wire and & bulb socket is right there. Give the socket a 1/4 turn to the left and you have access to replacing the bulb which is a 194, available at any parts store, 2 for $5.00.

Jul 07, 2012 | 1999 Buick Park Avenue

1 Answer

How do you replace a rear turn signal bulb on chevy hhr


There is an access panel on the inside rear sides by the lift gate. They pop out giving you access to the bulbs. I recommend replacing both at the same time since they seem to "blow" within a few days of each other.

May 20, 2010 | 2006 Chevrolet HHR

1 Answer

Rear turn signal and hazard light don't flash (left side only)


The rear left turn signal bulb must be replaced immediatly before it melts the light socket, if it has'nt yet. Also please verify that the correct light bulb is being installed. because even though many bulbs look the same they are not identical. Installing the wrong bulb can be the begining of many, many problems in the particular circuit

Mar 26, 2010 | 2000 Ford Focus

2 Answers

Left rear turn signal light on my 1999 chev. s10 is not working


any increase in bink speed is direcly related to a bulb being burt out.

Jun 12, 2009 | 1999 Chevrolet S-10 Pickup

2 Answers

1998 Ford Escort Left Front Turn Signal


replace rear left globe and this will solve both problems cheers MAL

Mar 17, 2009 | 1998 Ford Escort

1 Answer

Replacing rear turn signal bulb in 2003 Mustang


remove the trim panel at the very rear of trunk, remove it and place it out of the way, remove tail light Assembly retaining nuts top and bottom, I think there are 6 per side, pull the tail light assembly straight back to access the bulbs for replacement.

Dec 04, 2008 | 2003 Ford Mustang

1 Answer

Jeep Liberty Left Rear Turn Signal Not Working


sounds like the bulb you have is the wrong resistance the new noen bulbs will do this

Nov 16, 2008 | 2004 Jeep Wrangler

Not finding what you are looking for?
2000 Ford Expedition Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...