Question about 2004 Toyota Highlander
Can you tell me how to install replacement fog lights on a 2004 Toyota Highlander?
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
The link below is a Typical fog lamp / driving lamp hookup. Keep in mind that in most states, for these lamps to be 'legal' (and thus pass inspection), you must wire them such that:
1. You can cut them off (in other words, there must be a switch installed to turn them off)
2. They may only be operated with the low beams. (therefore, you must power your on/off switch from the low beam circuit)
Posted on Feb 28, 2009
SOURCE: How to replace fog light bulbs
hi..You will have to access the fog light bulb from below the vehicle.
Remove the plastic clips from the wheel well cover extension that is
below the fog light.once the clips are out and the plastic cover is pull
down,you should be able to see the back of the fog light.you can try
to replace the fog light bulb by removing the two 10mm bolts and slide
the fog light assemble out through the front of the bumper.Turn the cover
of the rear of the fog light and replace light.
try this out..
kindly rate my response..
Posted on Jun 14, 2009
fIRST YOU SEE A RUBBER GASKET SURROUNDING THE HEADLIGHT PLUG IN THE BACK OF THE HEADLIGHT ASSEMBLY. pULL OFF THE GASKET AND LET IT HANG ON THE SURROUN DING HEADLIGHT WIRES. tHEN PULL OFF THE HEADLIGHT WIRE HARNESS BY GRABBING THE SOCKET (NOT THE WIRES). AROUND THE BULB IS A THIN SILVER HOLDING SPRING THAT LOOSENS BY SQUEEZING THE ENDS TOGETHER AND ROTATING IT. iT WILL LOOSEN AROUND THE HEADLIGHT. WHEN THIS HAPPENS THE HEADLIGHT WILL "FLOP" AROUND AND PULL IT OUT, REMEMBERING TO SEE HOW THE THREE CONNECTORS ARE LOCATED (I.E - IS ONE CONNECTOR AT 12 O CLOCK POSITION AND THE OTHER TWO ARE AT 9 AND 3 OR ARE THEY AT 3,6 AND 9, ETC.). rE-ASSEMBLY IS THE OPPOSITIE. tHE TRICK IS TO GET THE THIN SPRING WIRE BACK IN PLACE. YOU HAVE TO SQUEEZE THE SPRING AND RE-POSITION IT SO IT KEEPS THE BULB SECURLY IN PLACE
Having just changed the bulb, I would advise taking the whole headlight assembly out first. It is near impossible to feel or imagine how to change the bulb without seeing it. First, use a phillips screwdriver to take the single screw holding the strip off just below the headlight assembly. By doing so, you will now see the other two bottom bolts holding the headlight in. Take all four bolts out then disconnect the bulb from behind. Then proceed as above.
Posted on Jun 14, 2009
If the shift console is on floor then look for bolts holding it down. Take out bolts and then you can maneuver console so you can see where light is plugged in and get the right light to replace it. It will probably be a small light which tend to cost a bit more, but at least you'll have the light back.
Posted on Apr 01, 2010
Tips for a great answer:
Oct 18, 2014 | 2002 Toyota Highlander
Jul 27, 2014 | 2004 Toyota Highlander
Apr 26, 2014 | 2012 Toyota Highlander Base 4dr SUV 2.7L...
Oct 19, 2011 | 2004 Toyota Highlander
Sep 15, 2017 | Toyota Highlander Cars & Trucks
Aug 18, 2010 | 2004 Toyota Highlander
Apr 01, 2010 | 2004 Toyota Highlander
Jun 14, 2009 | 2004 Toyota Celica
Sep 01, 2008 | 1998 Toyota Corolla
2,140 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: