Question about 2008 Toyota Tundra

Open Question

How to replace serpentine belt on 5.7 tundra - 2008 Toyota Tundra

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
abauto
  • 353 Answers

SOURCE: how do i change a serpentine belt for a 2007

Drive Belt: Service and Repair
DRIVE BELT

Components
43931e7.jpg


REMOVAL
1. REMOVE V-BANK COVER SUB-ASSEMBLY
2. REMOVE NO. 1 ENGINE UNDER COVER

4cff58f.jpg



3. REMOVE FAN AND GENERATOR V BELT
(a) While turning the belt tensioner counterclockwise, align the service hole for the belt tensioner and the belt tensioner fixing position, and
then insert a bar of [diameter]5 mm (0.197 in.) into the service hole to fix the belt tensioner in place.
HINT: The pulley bolt for the belt tensioner has a left-hand thread.
(b) Remove the V belt.



1. INSTALL FAN AND GENERATOR V BELT
(a) Set the V belt onto every part.
(b) While turning the belt tensioner counterclockwise, remove the pin.
NOTICE: Make sure that the V belt is properly set to each pulley.
(c) After installing the belt, check that it fits properly in the ribbed grooves.
HINT: Make sure to check by hand that the belt has not slipped out of the grooves on the bottom of the pulley.
2. INSTALL NO. 1 ENGINE UNDER COVER
3. INSTALL V-BANK COVER SUB-ASSEMBLY

c0b77ac.jpg

Posted on Sep 30, 2009

Ad
  • 50 Answers

SOURCE: how to change serpentine belt, 2004 Toyota Tundra

locate tensioner pulley; release tension from belt; remove belt; make sure not to forget how the belt is routed; route belt around all pulleys but tensioner; put tension on tensioner pulley; route belt over tensioner pulley

Posted on Oct 07, 2009

  • 1 Answer

SOURCE: Serpentine Belt routing diagram for 2007 Toyota

Installing fanbelt on 2007 Toyota Tundra 5.7

Posted on Oct 31, 2010

  • 333 Answers

SOURCE: chatter when turning

The serpentine belt should not have to be tightened because ther is a tensioner to keep it taught. If it feels loose then you need to check the tensioner and also see if the belt stretched. I hope this helps.

Posted on Jan 08, 2009

  • 1168 Answers

SOURCE: replaced serpentine drive belt 3 times. Replace

Hello diazrm.
When I see this happen in my shop we look carefully at all the pulleys to verify the bearings are turning smoothly and that there is no play in them.
The pulleys need to be parallel with each other and not tilted.
Not sure what year yours is or the engine size so I can't tell your setup.
Drive belt systems can also have automatic tensioners that wear on the pivot. This also allows the tensioner to tilt into the tension.
One of yours is doing this. No other reason for it.
Hope your repair goes well.
Best of the festive season to you.

KL

Posted on Dec 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Alternator location on a 2010Toyota tundra


if you open the hood standing in the middle of truck, facing towards the windshield, split the motor in half, the alternator should be left of center of motor, it is round, it has a pulley it may have 1 or 2 belts or 1 serpentine belt, if it is a serpentine belt you are going to need a tool call serpentine belt tool kit, long bar with a socket on the bar, set of different sizes of sockets to fit the spring load device that hold the serpentine belt in place. on top of alternator is a wire connector with 2-3 wires that connect to the starter and battery, and bolt with connector for ground that is bolted on the back side of alternator, 2-3 bolts that hold the alternator in place, remove bolts, take it auto parts store have them test it before buying a new one.

Apr 19, 2015 | 2010 Toyota Tundra

1 Answer

How do i replace the alternator on a 2000 tundra 4.7L 4x2 non serpentine configuration


I presume the serpentine belt is in the way. First, disconnect the battery terminal. Then make sure the serpentine belt diagram is readable and remove the serpentine belt. Then release the tension on the alternator belt and remove all the bolts and wiring.

Nov 20, 2014 | 2000 Toyota Tundra

1 Answer

What is the easiest and fastest way to replace the tundra serpentine belt?


loosen tensioner, take belt off, install new belt except last pulley, loosen tensioner, install belt on pulley, let tensioner tighten belt. If it takes 5 minutes, your doing something wrong.

Aug 25, 2010 | Toyota Tundra Cars & Trucks

1 Answer

How do you replace the serpentine belt on a 2007 toyota tundra 5.7


one of the idler pulleys is spring loaded ,look carefully to see what one it is then look to see if it has a square drive to put a rachet bar in to release the tension.

Jan 07, 2010 | 2000 Toyota Tundra

1 Answer

How to change serpentine belt, 2004 Toyota Tundra


locate tensioner pulley; release tension from belt; remove belt; make sure not to forget how the belt is routed; route belt around all pulleys but tensioner; put tension on tensioner pulley; route belt over tensioner pulley

Oct 03, 2009 | 2004 Toyota Tundra

1 Answer

How do i change a serpentine belt for a 2007


Drive Belt: Service and Repair
DRIVE BELT

Components
43931e7.jpg


REMOVAL
1. REMOVE V-BANK COVER SUB-ASSEMBLY
2. REMOVE NO. 1 ENGINE UNDER COVER

4cff58f.jpg



3. REMOVE FAN AND GENERATOR V BELT
(a) While turning the belt tensioner counterclockwise, align the service hole for the belt tensioner and the belt tensioner fixing position, and
then insert a bar of [diameter]5 mm (0.197 in.) into the service hole to fix the belt tensioner in place.
HINT: The pulley bolt for the belt tensioner has a left-hand thread.
(b) Remove the V belt.



1. INSTALL FAN AND GENERATOR V BELT
(a) Set the V belt onto every part.
(b) While turning the belt tensioner counterclockwise, remove the pin.
NOTICE: Make sure that the V belt is properly set to each pulley.
(c) After installing the belt, check that it fits properly in the ribbed grooves.
HINT: Make sure to check by hand that the belt has not slipped out of the grooves on the bottom of the pulley.
2. INSTALL NO. 1 ENGINE UNDER COVER
3. INSTALL V-BANK COVER SUB-ASSEMBLY

c0b77ac.jpg

Sep 28, 2009 | 2007 Toyota Tundra

1 Answer

Chatter when turning


The serpentine belt should not have to be tightened because ther is a tensioner to keep it taught. If it feels loose then you need to check the tensioner and also see if the belt stretched. I hope this helps.

Jan 08, 2009 | 2007 Toyota Tundra

Not finding what you are looking for?
2008 Toyota Tundra Logo

Related Topics:

3,040 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...